2-DIAL HOSE END TIMER BO92A I N S T R U C T I O N M A N U A L
TABLE OF CONTENTS Introduction........................................... 1 Timer Components................................ 2 Battery Installation................................. 3 Timer Installation................................... 4 Technical Data...................................... 5 Set Automatic Watering......................... 6 Changing Start Time............................. 7 Manual Start......................................... 8 Stop or No Watering..............................
2-DIAL Hose end timer Thank you for purchasing this timer, please read the operating instructions carefully to familarize yourself with the features and modes of operation before using the 2-Dial Hose End Timer.
Timer components Timer cover Inlet: 3/4 in. female hose thread with filter Outlet: 3/4 in.
battery installation • Hold the timer with the battery compartment facing you. • Remove the battery compartment. cover, lifting from one side. • Connect a 9V battery to. the battery connector. • Insert the . connected battery . and press on . the battery cover. NOTE: When battery is first connected, it takes . up to 1 minute for the battery indicator . to assess the battery strength. NOTE: When changing the battery, make sure the battery compartment stays dry. USE ONLY 9V ALKALINE BATTERIES.
timer installation Make sure the filter (washer) is in place, then screw the timer to the faucet or hose end by attaching the side with the female swivel hose thread connector to the hose end, then turn it clockwise (hand tighten only). Connect the timer hose male thread side to your system.
Technical data DIG Professional Grade – 2-Dial Hose End Timer Model: BO92A Operating pressure: 10 to 90 PSI Battery: Use a standard 9 Volt ALKALINE battery. Fluid: Only use cold water with NO added chemicals. Frequency Options: Every 6 hrs, 12 hrs, 24 hrs, 48 hrs, Every 3rd Day, Every 4th Day, Every 5th Day, Every 7th Day. Run Time Options: 2, 5, 10, 15, 30, 60, 120 or 240 Minutes.
set automatic watering SET RUN TIME & WATERING INTERVAL 1. Turn “LEFT” dial to select RUN TIME. 2. Turn “RIGHT” dial to select INTERVAL. 3. Push “ENTER” – The Red LED will appear solid for 10 seconds to confirm your selections, and then run. Watering will start in 24 hrs at the selected INTERVAL.
changing start time TO CHANGE THE START TIME (Minimum 6 Hours) 1. While the Red LED is solid ON, turn the “RIGHT” dial to select the DELAY time & press “ENTER” again. This moves the START time forward by the hours selected. RUN TIME will begin then & thereafter at selected INTERVAL.
manual start SETTING THE TIMER TO START MANUALLY 1. Turn “LEFT” dial to select RUN TIME. 2. Turn “RIGHT” dial to MAN and press “ENTER”. Note: Running a manual run time will not change any program previously entered. Watering will begin and end at selected RUN TIME.
stop or no watering HOW TO STOP THE TIMER WATERING 1. Turn “LEFT” dial to the OFF position. While the RUN TIME (Left) dial is in the “OFF” position NO watering will happen. Note: To re-commence automatic operation, move the “RUN TIME” dial to any other position.
red led – operating states Red LED – OPERATING STATES as follows: 1. SOLID: Confirms program & allows “START TIME” change. 2. FLASHING – 20 Seconds: “ALL IS RUNNING CORRECTLY”. 3. FLASHING – 1 Second: “BATTERIES NEED CHANGING”.
extra watering cycles The manual operation mentioned previously, can be used for running an extra cycle whilst the timer is programmed. The “Manual” cycle will run immediately after the enter button is pressed. The timer will resume the automatic program once the manual time has elapsed.
TROUBLESHOOTING 1. Ensure your faucet is turned on. 2. Ensure your battery is in good condition. USE ONLY ALKALINE BATTERIES. 3. Your program will start immediately and then at the frequency selected. Note: When the timer is not using an automatic program, it must be in the “OFF” position. Maintenance Turn the faucet off when the timer is not . in use. Check and clean screen washer periodically as needed. Remove the battery if the timer will not be used for a prolonged time.
WARRANTY DIG CORPORATION warrants these products to be free from defects in material and workmanship for a period of three years from date of purchase. DIG will repair or replace, at its option, free of charge, this product if it has proven to be defective within the three year period when said product is returned at customer expense to DIG within the warranty period. THIS WARRANTY DOES NOT COVER ANY EXPENSES INCURRED IN THE REMOVAL AND REINSTALLATION OF THIS PRODUCT.
warranty within three years after the original purchase and which on examination is found to contain defects in material and workmanship. DIG CORPORATION SHALL IN NO EVENT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND; THE SOLE OBLIGATION OF DIG BEING LIMITED TO REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
WARRANTY In the case of the purchase of the product for personal, family or household purposes, DIG CORPORATION disclaims any such warranties to the extent permitted by law. In order to obtain performance under this warranty, the unit must be returned to the factory, along with proof of purchase indicating original date of purchase, shipping prepaid, addressed as follows: . DIG CORPORATION, 1210 Activity Drive, Vista, CA 92081-8510.
TECHNICAL ASSISTANCE Should you encounter any problem(s) with this product or if you do not understand its many features, please refer to this instruction first. If further assistance is required, DIG offers the following customer support: Technical Service USA DIG’s Technical Service Team is available to answer questions in English and Spanish from 8:00 AM to 5:00 PM (PST) Monday-Friday (except holidays) at 800-344-2281. Questions in English and Spanish can be e-mailed to questions@ digcorp.
