User's Manual
Table Of Contents
- 1. Overview
- 2. RF Module Operation
- 3. XBee ZigBee Networks
- Introduction to ZigBee
- ZigBee Stack Layers
- Networking Concepts
- ZigBee Application Layers: In Depth
- Coordinator Operation
- Router Operation
- End Device Operation
- Channel Scanning
- 4. Data Transmission, Addressing, and Routing
- 5. Security
- 6. Network Commissioning and Diagnostics
- 7. Managing End Devices
- 8. XBee Analog and Digital IO Lines
- 9. API Operation
- API Frame Specifications
- API UART Exchanges
- Supporting the API
- API Frames
- AT Command
- AT Command - Queue Parameter Value
- ZigBee Transmit Request
- Explicit Addressing ZigBee Command Frame
- Remote AT Command Request
- Create Source Route
- AT Command Response
- Modem Status
- ZigBee Transmit Status
- ZigBee Receive Packet
- ZigBee Explicit Rx Indicator
- ZigBee IO Data Sample Rx Indicator
- XBee Sensor Read Indicator
- Node Identification Indicator
- Remote Command Response
- Over-the-Air Firmware Update Status
- Route Record Indicator
- Many-to-One Route Request Indicator
- Sending ZigBee Device Objects (ZDO) Commands with the API
- Sending ZigBee Cluster Library (ZCL) Commands with the API
- Sending Public Profile Commands with the API
- 10. XBee Command Reference Tables
- 11. Module Support
- Appendix A: Definitions
- Appendix B: Agency Certifications
- United States FCC
- OEM Labeling Requirements
- FCC Notices
- FCC-Approved Antennas (2.4 GHz)
- Europe (ETSI)
- OEM Labeling Requirements
- Restrictions
- Declarations of Conformity
- Approved Antennas
- XBee RF Module
- XBee-PRO (S2) RF Module
- XBee-PRO (S2B) RF Module
- Canada (IC)
- Transmitters for Detachable Antennas
- Detachable Antenna
- Appendix C: Migrating from ZNet 2.5 to XBee ZB
- Appendix D: Additional Information
XBee®/XBee‐PRO®ZBRFModules
©2009DigiInternational,Inc. 8
Key Features
Worldwide Acceptance
FCC Approval (USA) Refer to Appendix A for FCC Requirements.
Systems that contain XBee®/XBee-PRO® ZB RF Modules inherit Digi Certifications.
ISM (Industrial, Scientific & Medical) 2.4 GHz frequency band
Manufactured under ISO 9001:2000 registered standards
XBee®/XBee-PRO® ZB RF Modules are optimized for use in US, Canada, Europe,
Australia, and Japan (contact Digi for complete list of agency approvals).
High Performance, Low Cost
XBee
• Indoor/Urban: up to 133’ (40 m)
• Outdoor line-of-sight: up to 400’ (120 m)
• Transmit Power: 2 mW (3 dBm)
• Receiver Sensitivity: -96 dBm
XBee-PRO (S2)
• Indoor/Urban: up to 300’ (90 m), 200' (60
m) for International variant
• Outdoor line-of-sight: up to 1 mile (1600
m), 2500' (750 m) for International variant
• Transmit Power: 50mW (17dBm), 10mW
(10dBm) for International variant
• Receiver Sensitivity: -102 dBm
XBee-PRO (S2B)
• Indoor/Urban: up to 300’ (90 m), 200' (60
m) for International variant
• Outdoor line-of-sight: up to 1 mile (1600
m), 2500' (750 m) for International variant
• Transmit Power: 68mW (18dBm), 10mW
(10dBm) for International variant
• Receiver Sensitivity: -102 dBm
Advanced Networking & Security
Retries and Acknowledgements
DSSS (Direct Sequence Spread Spectrum)
Each direct sequence channel has over
65,000 unique network addresses available
Point-to-point, point-to-multipoint
and peer-to-peer topologies supported
Self-routing, self-healing and fault-tolerant
mesh networking
Low Power
XBee
• TX Peak Current: 40 mA (@3.3 V)
• RX Current: 40 mA (@3.3 V)
• Power-down Current: < 1 uA
XBee-PRO (S2)
• TX Peak Current: 295mA (170mA for
international variant)
• RX Current: 45 mA (@3.3 V)
• Power-down Current: < 10 uA
XBee-PRO (S2B)
• TX Peak Current: 205mA (117mA for
international variant)
• RX Current: 47 mA (@3.3 V)
• Power-down Current: < 10 uA
Easy-to-Use
No configuration necessary for out-of box
RF communications
AT and API Command Modes for
configuring module parameters
Small form factor
Extensive command set
Free X-CTU Software
(Testing and configuration software)
Free & Unlimited Technical Support