DECLARATION OF CONFORMITY Manufacturer’s Name: Manufacturer’s Address: DigiTech 8760 S. Sandy Parkway Sandy, Utah 84070, USA Warning For your protection, please read the following: declares that the product: Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Do not use this apparatus near water. 5. Clean only with dry cloth. conforms to the following Product Specifications: 6. Do not block any ventilation openings.
WARRANTY: We at DigiTech are proud of our products and back-up each one with the following warranty: 1.The warranty registration card must be mailed within ten days after purchase date to validate this warranty. 2. DigiTech warrants this product, when used solely within the U.S., to be free from defects in materials and workmanship under normal use and service. 3.
The Bass Driver Distortion is the world’s most advanced overdrive pedal designed specifically for bass. DigiTech’s exclusive AudioDNA™ technology is what makes the Bass Driver more than a standard overdrive stompbox. Rather than working with a single distortion circuit, the Bass Driver features a Morph knob that blends three totally distinct overdrive and distortion types. You now get a wide variety of overdrive sounds that can be dialed in quickly and easily. 1.
1 2 3 4 5 11 10 9 6 7 8
4. Blend Knob Controls the dry/distortion mix. Blending in dry signal helps maintain the bottom end that is usually lost when using a standard overdrive or distortion stompbox. At the Blend knob’s minimum position, only dry signal is heard. At the Blend knob’s maximum position, only distortion signal is heard. Experimenting with different Blend and Morph knob settings provides tremendous flexibility in the overall distortion sound. 5. Morph Knob Morphs the three different distortion sounds.
. Pedal Release Pins These two pins are spring-loaded hinges that hold the pedal in place. Push these pins in to release the pedal from the chassis exposing the battery compartment. (See battery replacement diagram.) 8. Pedal Turns the effect on and off. 9. Out 1(Amp) Jack Connect this output to your bass amplifier. 10. Indicator LED Indicates when the effect is turned on. If the LED becomes dim or does not light when the cables are connected, the battery needs to be replaced. 11.
Connections The Bass Driver has a single input (INPUT) and a pair of outputs (AMP and MIXER). The two outputs give you the following options: running into a bass amplifier, running directly to a mixing console or recording device, or both. The MIXER output uses DigiTech’s advanced CIT™ cabinet modeling technology for an authentic bass amplifier sound without using an amp. The CIT model is based on a 4x10 cabinet. Follow these setup directions: 1.
Battery Replacement 1. Using the tip of a 1/4” cable, push one of the release pins in on either side of the pedal, and remove the pedal from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. 3. Connect a new battery to the battery cable and put it back in the battery compartment. Make sure the battery cable does not interfere with the spring or pedal switch arm. 4. Place one hole of the pedal over its corresponding pin. 5.
Pedal Pedal Switch Arm 9V DC Battery Pedal Release Pin Battery Compartment Spring Pedal Release Pin Pedal Chassis
SPECIFICATIONS: • Controls - Level,Tone, Blend, Morph, On/Off Pedal • Jacks - Input, Out 1 (Amp), Out 2 (Mixer) • Input Impedance - 1 MOhms • Output Impedance - 100 Ohms • Power Supply - 9V Alkaline Dry Battery • Power Consumption - 4.8Watts (w/optional PS200R power supply) • Battery Life - Approximately 4 hours (with continuous usage) • Dimensions - 4 15/16”(L) x 3 1/8”(W) x 2 1/8”(H) • Weight - 1.38 lbs.