Installation manual
Table Of Contents
- About This Manual
- 1.0 Introduction
- 2.0 Installation
- 3.0 Scale Setup
- 4.0 Configuration Settings
- 5.0 Calibration
- 6.0 Scale Operations
- 7.0 Scale Programming
- 8.0 RS-232 Specifications
- 9.0 PC Connections and Label Formatting
- 10.0 Appendix
- 10.1 SPEC Code Worksheets
- 10.2 Scale Capacity and Display Resolution
- 10.3 Connector Pinouts
- 10.4 Cable Wiring
- 10.5 Y-Cable Wiring Diagram
- 10.6 DC-190 Messages
- 10.7 Clearing Locked-Up Scale (888888 Error)
- 10.8 DC-190 Character Code List (Teraoka Code)
- 10.9 Bar Code Board
- 10.10 PSC QuickScan 6000 Setup
- 10.11 DC-190 Ultra Count Specifications
- DC-190 Ultra Count Limited Warranty
38 DC-190 Ultra Count Installation Manual
8.4 Epson Ticket Printers
The Epson TM-U295 ticket printer default settings are
9600 baud rate, 8-bit data length, no parity and one
stop bit. The printer can be connected to either the
9-pin D-sub connector or the 8-pin DIN connector.
NOTE: Epson printers must be connected to the
DC-190 and powered on before powering up the
DC-190.
Table 8-8 presents the TM-U295 printer configuration
settings using SPECs 3, 10, 11, and 13 connected to
the 9-pin D-sub connector. Table 8-9 contains the
TM-U295 printer configuration settings using SPECs
3, 10, 11, and 13 connected to the 8-pin DIN
connector. Shown in Table 8-10 is the printer
configuration settings using SPECs 3, 10, 11, and 13
connected to a 9-pin sub-D connector while
Table 8-11 is the setting for an 8-pin DIN connector.
8.5 Digi BCP-300 Printer
The Digi BCP-300 bar code printer can be
attached only to the 8-pin DIN connector. Use the
SPEC settings listed in Table 8-12 to configure
the BCP-300. These settings provide a baud rate
of 9600, 8-bit data length, no parity, and one stop
bit.
SPEC Bit 3 Bit 2 Bit 1 Bit 0
3 0001
10 1111
11 0100
13 0000
Table 8-8. Epson TM-U295 (without Form Feed) Printer
Specification Connected to 9-Pin D-Sub Connector
SPEC Bit 3 Bit 2 Bit 1 Bit 0
3 0001
10 1111
11 0100
13 0001
Table 8-9. Epson TM-U295 (without Form Feed) Printer
Specification Connected to 8-Pin DIN Connector
SPEC Bit 3 Bit 2 Bit 1 Bit 0
3 0011
10 1111
11 0100
13 0000
Table 8-10. Epson TM-U295 Printer Specification (with
Form Feed) Connected to 9-Pin Sub-D Connector
SPEC Bit 3 Bit 2 Bit 1 Bit 0
3 0011
10 1111
11 0100
13 0001
Table 8-11. Epson TM-U295 Printer Specification (with
Form Feed) Connected to 8-Pin DIN Connector
SPEC Bit 3 Bit 2 Bit 1 Bit 0
3 0000
10 1111
11 0100
12 1000
13 0 0 — * 1
* SPEC 13, bit 1: Set to 1 if a PC is attached to the D-sub
connector; otherwise, set to 0.
Table 8-12. Digi BCP-300 Specifications