Digi One/PortServer TS 2/4 Configuration and Administration Guide 92000307_B
The Digi logo is a trademark of Digi International. All other brand and product names are trademarks of their respective holders. © Digi International Inc., 1998, 2000, 2001, 2002. All Rights Reserved http://www.digi.com Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International.
Contents Chapter 1 Introduction Setup Overview.................................................................................................... 1-2 About This Guide................................................................................................. 1-3 About Entering Commands on the Command Line............................................. 1-3 Supported Devices ...............................................................................................
Chapter 8 Configuring PPP Configuring PPP Connections: Web Interface..................................................... 8-2 Configuring Inbound PPP Connections: Command Line .................................... 8-3 Configuring Outbound PPP Connections: Command Line ................................. 8-5 Chapter 9 Configuring IP Routing Introduction to Routing ........................................................................................ 9-2 About RIP Routing Updates ..............................
Chapter 17 Configuration Examples Terminal Server Configuration Without RealPort ............................................. 17-2 Terminal Server Configuration Using Autoconnection ..................................... 17-3 Terminal Server Configuration Using RealPort ................................................. 17-4 Chapter 18 Digi One/PortServer TS 2/4 Troubleshooting Symptom: Digi One/PortServer TS 2/4 Does Not Boot ....................................
iv
Introduction Chapter 1 In This Chapter This chapter provides a brief introduction on setting up your Digi device. It discusses the following topics: Introduction • Setup Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 • About This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 • About Entering Commands on the Command Line. . . . . . . . . . . . . . . . . . . . . .
Setup Overview This section provides an overview of the setup process. Step A: Plan Before beginning setup, consider the following: • How to assign an IP address to the Digi device’s Ethernet interface, which can be accomplished in a number of ways. See "Configuring the IP Address" on page 2-1. • How to configure serial ports. A key consideration is whether to use RealPort. Other considerations include the type of peripheral that will connect to the port and the peripheral’s cabling requirements.
About This Guide Purpose This guide provides the following: • Configuration and administration procedures • Configuration examples Audience This manual is intended for the person responsible for configuring and administering Digi One/PortServer TS 2/4. It assumes that this person has experience configuring network devices and is familiar with networking concepts. Scope This manual provides step-by-step instructions for configuring and administering Digi One/PortServer TS 2/4’s main features.
Other Documents in the Library Here is a list of the other documents in the library: Access Resource CD Card This card provides information on the contents of the Access Resource CD. It includes the CD mounting instructions required to access the CD on many Unix systems. Digi One/PortServer TS 2/4 Setup Card This card, which comes in the Digi One/PortServer TS 2/4 package, provides a brief overview on the setup process.
About Configuration Methods Use this section to learn about configuration methods. Configuring the Digi One/PortServer TS 2/4 from an Attached Terminal With this method, you cable a terminal or PC running terminal emulation software to a Digi One/PortServer TS 2/4 port and then use the command line to enter commands. This method allows you to configure all features. It requires, however, that you and the Digi One/PortServer TS 2/4 be in the same location.
Configuration Prerequisites Accessing the Command Line from a Locally-Connected Terminal Use this procedure to access the command line and the configuration from a terminal connected to one of the Digi One/PortServer TS 2/4’s serial ports. 1. Connect a terminal or PC to a serial port on the Digi One/PortServer TS 2/4. • For a terminal, use the cable that came with your package.
Configuring the IP Address Chapter 2 In This Chapter This chapter discusses how to configure Digi One/PortServer TS 2/4’s IP address and other features associated with its Ethernet interface. It discusses the following topics: • Options for Configuring the IP Address and Mask . . . . . . . . . . . . . . . . . . . . . . 2-2 • Configuring the Ethernet Interface with DPA-Remote . . . . . . . . . . . . . . . . . . . 2-3 • Configuring the IP Address Using Ping-ARP . . . . . . . . . . . . . . . . . . . . .
Options for Configuring the IP Address and Mask Options The Digi One/PortServer TS 2/4 IP address can be configured using the following methods: • With Digi Port Authority-Remote, a Digi utility • By updating the ARP table on a server and then pinging the Digi device (called Ping-ARP) • From the command line using the set config command • Using a RARP server • Using a DHCP server The IP address and mask can also be changed using the web interface.
Configuring the Ethernet Interface with DPA-Remote Use this section to configure an initial IP address, subnet mask, and default gateway using DPARemote. This procedure cannot be used to change the IP address, but only to assign the initial IP address. It also cannot be used if a DHCP server is active. Starting Point This procedure assumes the following: • That your Digi device supports this feature. See "Devices That Support DPA-Remote and PingARP for IP Address Configuration" on page 2-2.
Configuring the IP Address Using Ping-ARP Use this section to configure an IP address by manually updating a server’s ARP table and then pinging the Digi device. Starting Point This procedure assumes the following: • That your Digi device supports this feature. See "Devices That Support DPA-Remote and PingARP for IP Address Configuration" on page 2-2. • That your Digi device is connected to the Ethernet network Procedure 1. Record the MAC address of the Digi device. It’s on the back of the unit. 2.
Configuring the Ethernet Interface from the Command Line This section discusses how use the command line to configure an IP address, mask, and default gateway for Digi One/PortServer TS 2/4’s Ethernet interface. Manual Configuration Procedure 1. To configure an IP address for the Ethernet interface, enter the following command: set config ip=ip-address where ip-address is the IP address for the Ethernet interface Example: set config ip=191.143.2.154 2.
2-6 Configuring an IP Address using DHCP and RARP
Configuring Ports for RealPort Chapter 3 In This Chapter This chapter describes how to configure Dig One/PortServer TS 2/4 for RealPort connections. It discusses the following topics: • About RealPort. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 • Configuring Ports: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 • Configuring Ports for RealPort: Command Line . . . . . . . . . . . . . . . . . . . . . . .
About RealPort This section provides a brief introduction to RealPort. What is RealPort? RealPort is a feature that allows network-based host systems to use the ports of the Dig One/PortServer TS 2/4 as though they were the host system’s own ports, appearing and behaving as local ports to the network-based host. RealPort Advantages RealPort provides the following advantages: • It expands the number of ports available to the host system.
Configuring Ports: Web Interface Use this procedure to configure a port from the web interface. 1. Access the web interface by entering the Dig One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Dig One/PortServer TS 2/4 as root. The default password is dbps. 3. From the main menu, select Configure > RealPort. A screen similar to the following appears. 4. To complete configuration, choose Next and then follow the prompts. 5.
Configuring Ports for RealPort: Command Line This section describes how to configure RealPort ports from the command line. Procedure Use this procedure to use the command line to configure Dig One/PortServer TS 2/4 for RealPort. This procedure assumes that you have signed on as root and have or will • Install RealPort software on each RealPort host. See the appropriate RealPort documentation for more information. • Properly cabled Dig One/PortServer TS 2/4 ports and devices.
Configuring Ports for Printers Chapter 4 In This Chapter This chapter describes how to configure Dig One/PortServer TS 2/4 ports for printer connections. It discusses the following topics: • Configuration Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 • Configuring Ports for Printers: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 • Configuring Printer Connections: Command Line . . . . . . . . . . . . . . . . . . . . . .
Configuration Considerations You should be aware of the following considerations if you intend to configure Dig One/PortServer TS 2/4 to handle printers. Using RealPort RealPort, a feature that allows network-based host systems to use the ports of the Dig One/PortServer TS 2/4 as though they were the host system’s own ports, is an easy and efficient way for printers to use Dig One/PortServer TS 2/4 ports. For information on this option, see "Configuring Ports for RealPort" on page 3-1.
Tips for telnet and rsh Printing Here are some tips for handling telnet and rsh printing: • If line feed and carriage return problems occur, try supplying a set line command that specifies onlcr=on. This converts carriage returns to carriage return/line feeds. • If you want tab characters (ASCII character 9) converted to 8 spaces, use a set line command that specifies otab=on. Configuring Ports for Printers: Web Interface Use this procedure to configure a port from the web interface. 1.
set line range=2 baud=9600 csize=8 stopb=1 parity=n set flow range=2 cts=on ixon=off ixoff=off 4-4 Configuring Printer Connections: Command Line
Configuring a Port for Direct-Access Printing Direct access printing allows Telnet users on the LAN to access a port and to issue print commands directly to the printer. This section describes the two ways users can access a printer directly and explains how to configure the port to support each method. Method 1: Specifying Port Numbers in the Telnet Command This method allows users to issue telnet commands that identify the correct port by using TCP port numbers.
4-6 Configuring a Port for Direct-Access Printing
Configuring Ports for Modems Chapter 5 In This Chapter This chapter describes how to configure Digi One/PortServer TS 2/4 ports for modem connections. It discusses the following topics: • Tips on Configuring A Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 • Configuring Ports for Modems: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 • Configuring Ports for Incoming Modem Connections: Command Line . . . . . .
Tips on Configuring A Modem Here are some tips on configuring modems to work with Digi One/PortServer TS 2/4: • Configure the modem so that DCD goes high when it receives an incoming connection request. • Configure the modem to answer an incoming call only when DTR is high, and to drop the line when DTR goes low. • For bidirectional connections, it is advisable to configure the non-volatile parameters in the modem for incoming calls. Also configure the modem to reset to these parameters when DTR is dropped.
Configuring Ports for Modems: Web Interface Use this procedure to configure a port for a modem from the web interface. 1. Access the web interface by entering the Digi One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Digi One/PortServer TS 2/4 as root. The default password is dbps. 3. From the main menu, choose Configure > Ports. 4. To configure a port, do the following: a. Choose the port from the port column. b. Configure the correct device type.
Example In this example, ports 1 and 2 are set up for incoming modem connections using RTS/CTS flow control. set ports range=1-2 dev=min set line range=1-2 baud=115200 set flow range=1-2 ixon=off ixoff=off cts=on rts=on Configuring Ports for Outgoing/Bi-Directional Connections: Com m and Line This section describes how to configure outgoing and bidirectional modem connections from the command line.
Configuring Ports for Terminals and Computers Chapter 6 In This Chapter This chapter describes how to configure Digi One/PortServer TS 2/4 ports for terminal and computer connections. It discusses the following topics: • Configuring Ports for Terminals: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . 6-2 • Configuring Ports for Terminals: Command Line . . . . . . . . . . . . . . . . . . . . . . . 6-2 • About Computer Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Configuring Ports for Terminals: Web Interface Use this procedure to configure a port from the web interface. 1. Access the web interface by entering the Digi One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Digi One/PortServer TS 2/4 as root. The default password is dbps. 3. From the main menu, choose Configure > Ports. 4. To configure a port, do the following: a. Choose the port from the port column. b. Ensure that the Device type is set to Terminal. c.
• bps is the line speed • characters is the character size • parity is the parity scheme to use on this line • num-bits is the number of stop bits to use 3.
6-4 About Computer Connections
Configuring Autoconnection Chapter 7 In This Chapter This Chapter discusses how to configure the autoconnection feature. It covers the following topics: • About Autoconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 • Configuring a Port for Autoconnection: Web Interface . . . . . . . . . . . . . . . . . . . 7-2 • Configuring Autoconnection By Port: Command Line . . . . . . . . . . . . . . . . . . .
About Autoconnection The autoconnection feature allows you to configure a user to access the Digi One/PortServer TS 2/4 and then be automatically connected to a host on the LAN. You can implement autoconnection in the following ways: • By port. In this case, all port users are automatically connected to the same host. The Digi One/PortServer TS 2/4 is completely transparent to them. • By user.
Configuring a User for Autoconnection: Web Interface 1. Access the web interface by entering the Digi One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Digi One/PortServer TS 2/4 as root. The default password is dbps. 3. Select Configure and then Users from the menu. 4. To add an autoconnect user, do the following: a. Choose Add User. b. Enter a name and then choose Submit c. Choose the new user from the Name column. d. Configure the user.
7-4 Configuring a User for Autoconnection: Command Line
Configuring PPP Chapter 8 In This Chapter This chapter discusses how to configure PPP connections. It covers the following topics: Configuring PPP • Configuring PPP Connections: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 • Configuring Inbound PPP Connections: Command Line . . . . . . . . . . . . . . . . . 8-3 • Configuring Outbound PPP Connections: Command Line . . . . . . . . . . . . . . . .
Configuring PPP Connections: Web Interface Use this procedure to configure PPP connections from the web interface. 1. Access the web interface by placing the IP address of the Digi device in the URL window of a browser. 2. Log in as the root user. The default password is dbps. 3. Navigate to the PPP configuration screen, by choosing PPP from the Configure menu. A screen similar to the following appears. 4. Use the web interface and the online help to complete configuration tasks.
Configuring Inbound PPP Connections: Command Line Use this section to configure simple inbound PPP connections from the command line. For information on fine-tuning PPP connections, see the set user command in the Digi One/PortServer TS Command Reference. Note: CHAP authentication works between two Digi devices. CHAP will be negotiated to PAP for all other connections Procedure 1.
7. To configure an IP address for the local end of the PPP connection, enter the following command: set user name=name localipaddr=ip-address where name is the user’s name and ip-address is the IP address to assign to the local end of the PPP connection. This address must be unique. That is, no other user can be assigned this address and it cannot be the IP address for the Ethernet interface. Example: set user name=pppin localipadr=199.1.1.
Configuring Outbound PPP Connections: Command Line This section describes how to configure outbound PPP connections. Use it to configure outbound only connections or to configure the outbound portion of bidirectional connections. Note: CHAP authentication works between two Digi devices. CHAP will be negotiated to PAP for all other connections Procedure 1.
set user name=name outgoing=on device=device where device is either the Digi-supplied device or the outbound device created earlier in this procedure Example: set user name=pppout outgoing=on device=gendialer 8. To configure an IP address for the local end of the PPP connection, enter the following command: set user name=name localipaddr=ip-address where name is the user’s name and ip-address is one of the following: • 0.0.0.0. , which means that the user will request an IP address from the remote server.
Configuring IP Routing Chapter 9 In This Chapter This chapter describes how to configure IP routing. It discusses the following topics: • Introduction to Routing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2 • About RIP Routing Updates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3 • Configuring Static Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction to Routing This section provides some introductory information on routing. What is Routing Routing is the method, employed by IP software, of choosing a path over which to send packets between systems on different physical networks. When Digi One/PortServer TS 2/4 is configured as a router, it performs this service. Types of Routing Digi One/PortServer TS 2/4 can be configured to perform the following types of routing: • Static routing.
About RIP Routing Updates Introduction RIP defines a method for propagating routing information among routers. It provides IP software with the information needed to make intelligent routing decisions. The information, passed in RIP updates packets from router-to-router, consists of two items, a network ID and a hop count. A hop count is the number of routers through which a packet must pass on its way from a source to a destination network.
regarded R2 as an alternate path to Net 1. The second is called “poison reverse,” which stipulates that routes are advertised as unreachable on the interface on which the route is learned. Had poison reverse been used in the preceding example, R2 would have advertised Net 1 as unreachable in its RIP updates to R1. Again R1 would never have regarded R2 as an alternate path to Net 1.
Configuring Static Routes This section describes how to configure Digi One/PortServer TS 2/4 for static routes. Related Information See the set route command in the Digi One/PortServer TS Command Reference.
Configuring Dynamic Routes Using RIP This section describes how to configure Digi One/PortServer TS 2/4 for dynamic routing. Related Information See the set forwarding command in the Digi One/PortServer TS Command Reference. Starting Point This procedure assumes that you have sign on as root and have or will configure modems, modem scripts, devices, and filters for routes that use serial lines. Procedure 1. Configure the links over which routed packets and RIP updates will be sent.
Configuring Proxy ARP This section describes how to configure Digi One/PortServer TS 2/4 for Proxy ARP. Related Information See the set forwarding command in the Digi One/PortServer TS Command Reference. Starting Point This procedure assumes that you have signed on as root and have or will configure modems, modem scripts, devices, and filters for routes that use serial lines. Procedure 1. Configure the links over which packets will be routed using a set user command.
9-8 Configuring Proxy ARP
Configuring Console Management Chapter 10 In This Chapter • About Console Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 • Configuring Console Management: Web Interface . . . . . . . . . . . . . . . . . . . . . 10-2 • Configuring Console Management: Command Line . . . . . . . . . . . . . . . . . . . .
About Console Management Digi One/PortServer TS 2/4 can be configured to remotely manage network devices, such as routers, switches, and servers, which usually provide EIA-232 serial ports for management. Using the Digi One/PortServer TS 2/4 and TCP/IP utilities like reverse Telnet and SSH2, network administrators can access consoled serial ports from a single station over the LAN. Configuring Console Management: Web Interface 1.
where • name is the name of a user • host is either an IP address or DNS name of a host running TFTP • key is the name of a file that contains the DSA public key. If your host’s implementation requires a complete path to the file, specify the path here as well. Example: set user name=secure loadkey=143.191.2.
10-4 Configuring Console Management: Command Line
Configuring Modbus Chapter 11 In This Chapter • About Modbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11-2 • Configuring Modbus Using the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . .11-3 • Configuring Modbus from the Command Line . . . . . . . . . . . . . . . . . . . . . . . . .11-4 • Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Modbus What Is Modbus Modbus is a protocol that defines a method for devices in an industrial automation environment to communicate. It allows a single controlling unit, called a protocol master, to manage one or more units, called protocol slaves. The protocol specifies that only the master may initiate communication. Slaves may only respond.
Configuring Modbus Using the Web Interface 1. Access the Digi One/PortServer TS 2/4 from a web browser by entering the Digi One/PortServer TS 2/4 IP address in the URL window. 2. Sign on to the Digi One/PortServer TS 2/4. 3. Choose Modbus from the menu. 4. Fill in fields as required. Use the context-sensitive help for guidance. 5. Configure ports for modbus, by doing the following: a. Select Ports. b. Specify Modbus as the device type. c. Configure other port attributes as required by the attached device.
Configuring Modbus from the Command Line Use this procedure to configure a Digi device for Modbus. Starting Point This procedure assumes that you have logged on to the Digi device as root. Procedure 1.
• A Modbus protocol unit number for each slave. This can be specifies in any of the following ways: (a) An individual unit number. (b) A range of unit numbers. (c) All, which means accept messages carrying any Modbus protocol unit number. • Timers as required. Typically the defaults work. If you require additional information, see the set modbus command in the Digi One/PortServer TS 2/4 Command Reference.
Examples Configuring Network-Connected Masters Introduction Here are a few points regarding this configuration: • All timers for both masters and slaves are using defaults. • The range field on the set modbus master command is an index number that Digi One IA identifies these masters. The range fields on each of the set modbus slave commands identify the individual slaves. • The slaves field on the set modbus master command then identifies the slaves that belong to this master.
Configuring Security Features Chapter 12 In This Chapter This chapter describes Digi One/PortServer TS 2/4 security features and discusses how to configure them. It presents the following topics: • Controlling Access to the Digi One/PortServer TS 2/4 Configuration . . . . . . 12-2 • Controlling Access to Inbound Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2 • Controlling Access to Outbound Ports. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controlling Access to the Digi One/PortServer TS 2/4 Configuration Digi One/PortServer TS 2/4 restricts access to the configuration by defining the following types of users: • The root user, who has unlimited access to Digi One/PortServer TS 2/4 commands. He or she can view any configuration table and change any configuration parameter. The root is identified by the user name root and must supply a password to be authenticated. The default root password is dbps. You should change this password immediately.
Controlling Access to Outbound Ports This section describes methods for controlling access to outbound serial ports. An outbound port is one defined on the dev field of the set ports command for one of the following device types: • prn (used to define printer connections) • mout (used to define outbound modem connections • mio (used to define bi-directional modem connections) • host (used to define host connections) • modbus Default Access The default for outbound ports is unlimited access.
Issuing User Passwords This section discusses how to issue user passwords. Related Information See the newpass and set user commands in the Digi One/PortServer TS Command Reference. Starting Point This procedure assumes that you have signed on as root and already configured the user to whom you will be issuing a password. Procedure 1. Issue a newpass command that identifies the user (on the name field) to whom this password will be issued. 2.
Configuring SSH Version 2 for Secure Communication This section discusses how to configure a user to use SSH version 2 encryption. This feature is only available for the following devices. Device Required Hardware Digi One TS 50000771-01A or higher PortServer TS 2 50000771-02A or higher PortServer TS 4 50000771-03A or higher Required Firmware 82000747a or higher Password Protection To configure simple password authentication for an SSH user, no SSH-specific configuration is required.
12-6 Configuring SSH Version 2 for Secure Communication
Configuring DNS Chapter 13 In This Chapter This chapter discusses how to configure Digi One/PortServer TS 2/4 to use DNS. Topics discussed include the following: Configuring DNS • About the Domain Name System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2 • Configuration Procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About the Domain Name System This section discusses key concepts of the domain name system. Purpose of DNS The domain name system maps domain names to information associated with these names, such as IP addresses.
Configuration Procedures Procedure for Using a Name Server To configure a DNS server, enter the following command: set config domain=domain myname=name dns=ip-address where • domain is the domain in which the Digi One/PortServer TS 2/4 will reside • name is a DNS name for Digi One/PortServer TS 2/4 • ip-address is the IP address of a name server Example: set config domain=digi.com myname=poe dns=204.221.1.
13-4 Configuration Procedures
Configuring SNMP Chapter 14 In This Chapter This chapter describes how to configure the Digi One/PortServer TS 2/4 SNMP agent. It discusses the following topics: Configuring SNMP • About SNMP and the Digi One/PortServer TS 2/4 Agent. . . . . . . . . . . . . . . . 14-2 • Configuration Procedure: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-3 • Configuration Procedure: Command Line . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About SNMP and the Digi One/PortServer TS 2/4 Agent This section introduces SNMP and network management in TCP/IP networks, and it describes the Digi One/PortServer TS 2/4 agent.
Configuration Procedure: Web Interface 1. Access the web interface by entering the Digi One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Digi One/PortServer TS 2/4 as root. The default password is dbps, which should be changed. See the newpass command in the Digi One/PortServer TS Command Reference for information on changing passwords. 3. Select Configure and then SNMP from the menu. 4. Fill in the configuration fields and then press Submit.
14-4 Configuration Procedure: Command Line
Configuring Users Chapter 15 In This Chapter This chapter discusses how to configure users. It covers the following topics: • Configuring Users About Configuring Users . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2 • Common User Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-2 • Configuring a User: Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Configuring Users Although it is not required, the Digi One/PortServer TS 2/4 is often configured to accommodate the requirements of particular users.
Configuring a User: Web Interface Use this section to configure users with from the web interface. 1. Access the web interface by entering the Digi One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Digi One/PortServer TS 2/4 as root. The default password is dbps. 3. Select Configure and then Users from the menu. 4. To add a user, do the following: a. Choose Add User. b. Enter a name and then choose Submit c. Choose the new user from the Name column. d.
Configuring a User: Command Line Examples This section consists of a set of examples that tell you how to use the set user command to configure various user attributes. Configuring a User for a Password In this example, the set user command configures a new user. The newpass command then initiates a dialog with the Digi One/PortServer TS 2/4 to assign a password to the new user.
Managing the OS and Configuration Chapter 16 In This Chapter This chapter provides information on updating the operating system (OS) and managing the configuration. Topics include the following: • Upgrading the OS (Firmware): Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . 16-2 • Upgrading the OS (Firmware): Command Line . . . . . . . . . . . . . . . . . . . . . . . 16-3 • Configuring Digi One/PortServer TS 2/4 from a Remote Host. . . . . . . . . . . .
Upgrading the OS (Firmware): Web Interface Use this section to upgrade the firmware using the web interface. 1. Access the web interface by entering the Digi One/PortServer TS 2/4 IP address in a browser’s URL window. 2. Log in to the Digi One/PortServer TS 2/4 as root. The default password is dbps. 3. From the main menu, choose Admin and then either HTTP upgrade or TFTP upgrade. 4. Follow the prompts to complete the upgrade.
Upgrading the OS (Firmware): Command Line This section describes how to upgrade the Digi One/PortServer TS 2/4 operating system (OS). The OS is stored in flash ROM and can be upgraded without changing the ROM or other hardware. Related Information See the boot and set config commands in the Digi One/PortServer TS Command Reference. Prerequisite Task Note: When upgrading from a firmware release prior to 82000716_B , the POST code must be upgraded first.
Configuring Digi One/PortServer TS 2/4 from a Remote Host This section discusses remote configuration, that is, configuring Digi One/PortServer TS 2/4 from a remote host and then downloading the configuration file to Digi One/PortServer TS 2/4.
Copying a Configuration File from a Host to Digi One/PortServer TS 2/4 This section describes how to copy the configuration file from a host to Digi One/PortServer TS 2/4 after the file has been edited on the host. Related Information See the cpconf command in the Digi One/PortServer TS Command Reference.
Resetting the Configuration to Defaults Use this section to learn how to use the revert command to reset the all or some of the configuration factory or to the latest configuration stored in NVRAM. Note: You can also use the range field on this command to define a range of ports with the serial, port, line, flow, keys and login options. To Reset the ... 16-6 To factory defaults specify ... To the latest version in NVRAM specify...
Configuration Examples Chapter 17 This chapter provides several simple, but complete, configuration examples. If you find that the examples implement exactly the features needed for your network, simply copy them, making appropriate substitutions for site-specific information such as IP addresses.
Terminal Server Configuration Without RealPort In this configuration, Digi One/PortServer TS 2/4 functions as a terminal server, providing Telnet and Rlogin access to hosts. This configuration enables the following: • Telnet or Rlogin access to the LAN-based hosts, both from locally-connected terminals and from devices accessing the LAN from the telephone network.
Terminal Server Configuration Using Autoconnection This example shows a Digi One/PortServer TS 2/4 functioning as a terminal server implementing autoconnection. • The terminals are connected to autoconnect ports. Consequently, when a user presses a terminal key, an automatic connection to a host is made. • The modem ports are not configured for autoconnection, but a port user is, which means that as soon as this particular user supplies a login, an automatic connection to a host is made.
Terminal Server Configuration Using RealPort In this example, the Digi One/PortServer TS 2/4 is simply providing ports for the LAN-based host using RealPort. The configuration is exceedingly simple because port attributes are configured on the host itself. Related Information For more information on configuring: • The Ethernet interface, see "Configuring the IP Address" on page 2-1 • RealPort, see "Configuring Ports for RealPort" on page 3-1 Illustration 192.250.150.
Digi One/PortServer TS 2/4 Troubleshooting Chapter 18 In This Chapter • Symptom: Digi One/PortServer TS 2/4 Does Not Boot . . . . . . . . . . . . . . . . . 18-2 • Symptom: Cannot Telnet to the Digi One/PortServer TS 2/4 . . . . . . . . . . . . . 18-3 • Symptom: Trouble Accessing a Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18-4 • Running Digi One/PortServer TS 2/4 Customer Diagnostics . . . . . . . . . . . . . 18-4 • Key to Interpreting Digi One/PortServer TS 2/4 LEDs .
Symptom: Digi One/PortServer TS 2/4 Does Not Boot Introduction Use the information provided in this discussion when Digi One/PortServer TS 2/4 will not complete the boot cycle. Procedures Things to Try See ... • Check for hardware problems. Check for TFTP problems if Digi One/PortServer TS 2/4 is booting from a TFTP host.
Symptom: Cannot Telnet to the Digi One/PortServer TS 2/4 Introduction Use the information provided in this discussion to troubleshoot network problems. Assumptions This discussion assumes that the Digi One/PortServer TS 2/4 itself is working, that is, that it completes the boot cycle. Procedures Things to Try See ... Verify the IP address. This procedure ensures that you are using the right IP address to Telnet to the Digi One/PortServer TS 2/4.
Symptom: Trouble Accessing a Port Introduction Use this procedure if you are having trouble accessing a Digi One/PortServer TS 2/4 port. The specific problem might be that you cannot logon from a terminal or the printer or modem is not working properly. Assumptions This discussion assumes the following: • That the Digi One/PortServer TS 2/4 itself is working, that is, that it completes the boot cycle. If it is not, see "Symptom: Digi One/PortServer TS 2/4 Does Not Boot" on page 18-2.
Key to Interpreting Digi One/PortServer TS 2/4 LEDs Here is a key to interpreting Digi One/PortServer TS 2/4 LEDs Procedure . Indication LED Activity 1-1-1 pattern Starting the EOS. 1-3-1 pattern TFTP boot process started 1-5-1 pattern Tells you that configuration has been return to the factory configuration. See "Resetting Digi One/PortServer TS 2/4 Configuration to Defaults" on page 18-6. Steady blinking Device seeking an IP address from DHCP server.
• • mkdir /tftpboot If necessary, use this command to change permissions of the directory to read, write and execute: chmod 777 /tftpboot Verify that the file /tftpboot/tftp_file_name exists and has read and execute permissions with this command: ls -l /tftpboot/tftp_file_name where tftp_file_name is the name of the firmware boot image specified by the Digi Device.
Verifying the Digi One/PortServer TS 2/4 IP Address Use this procedure to check the IP address on the Digi One/PortServer TS 2/4. 1. Connect a terminal to a Digi One/PortServer TS 2/4 port. 2. If the port is still using the default configuration, configure the terminal to use the following settings (Otherwise, configure the terminal to match the port configuration): • VT-100 emulation • 9600 baud • 8-bit characters • 1 stop bit • No parity 3.
Verifying the Network Cabling Use this procedure to troubleshoot network cabling problems. 1. Check the Ethernet cable. Verify the following: • The Ethernet cable is connected securely at both ends. • The Ethernet cable is pinned correctly. • The quality of the cable is sufficient for the cable length and the cable environment. Consult an Ethernet cable manufacturer for a recommended cable for your configuration. 2. Verify your Ethernet hub. See your Ethernet hub manual.
Verifying the RealPort Process Use one of these procedures to verify the RealPort process: AIX: Verifying the RealPort Process Use this topic to verify that the RealPort daemon (process) is running on the AIX system. 1. Type the following: lsdev -Cc nts 2. If the sa devices are not in an available state, type the following from the AIX prompt: mkdev -1 sa# cfgmgr where # is the number of the Digi Device. HP-UX: Verifying the RealPort Process 1.
Solaris: Verifying the RealPort Process Use this topic for information on verifying that the RealPort process is running on a Solaris system. 1. Type the following command: ps -ef|grep ncxd 2. If the information that appears is not correct, do the following: a. Modify the /etc/rc2.d/S26realport file with the appropriate IP addresses. b. Reboot the UNIX server. Windows NT: Verifying the RealPort Service Use this procedure to verify the RealPort service on Microsoft Windows NT. 1.
Digi Contact Information Digi International 11001 Bren Road East Minnetonka, MN 55343 U.S.A Customer Service and Support World Wide Web: http://support.digi.com email support@digi.com Telephone (U.S.
18-12 Digi Contact Information
