SERVICE MANUAL DIGITAL COMPUTING PRINTING SCALE SM-500MK4 Edition 1 COPYRIGHT © 2006 TERAOKA WEIGH-SYSTEM PTE LTD
Table of Content 1. 2. i) Notice 1 ii) Safety Information ..............................................................................................................................2 GENERAL ....................................................................................................................................................3 1.1 Model Specification ............................................................................................................................3 1.
5.2.1 5.2.2 5.2.3 5.2.4 5.3 Maintenance.....................................................................................................................................28 5.3.1 5.3.2 5.3.3 5.4 6. 7. 8. 10. Thermal Head Cleaning ......................................................................................................28 Basic Maintenance.............................................................................................................29 Thermal Head cleaning and replacement ..
i) Notice DIGI® The material contained in this document is proprietary and for information only and is subject to change without notice. Teraoka Weigh-System assumes no responsibility for any errors or damages arising from misinterpretation of any procedure. Screen displays, operating procedures and supporting features might vary with different software version releases. This document shall not be reproduced whether in part or whole without the written consent from Teraoka Weigh-System Pte Ltd.
ii) Safety Information The operator of the equipment shall comply with the safety and warning indications and procedures outlined in this document. Teraoka Weigh-System Pte Ltd assumes no responsibility or liability for failure to comply with these requirements. • To avoid electric shock, use only the supplied power cords and ensure product is connected to a properly grounded supply. • For continued protection against fire hazard replace only with fuse of same rating and type.
SM500MK4 Service Manual 1. GENERAL 1.
SM500MK4 Service Manual 1.2 Operating Specification Power Source : 100V to 240V AC (Auto Switching) Frequency : 50 - 60 Hz Operating Temperature : -10 °C to 40 °C Humidity : 15 % to 85 % RH Waterproof : N.A. (Please do not splash water on top or around the scale. Clean scale only with a damp cloth) : : : : RS 232C (FL-1, PC connection) PS2 Keyboard Cash drawer (3 Pin for TWB-01750) 1.
SM500MK4 Service Manual 2. OVERVIEW 2.1 Dimension Dimensions are in mm 2.1.1 Pole 570 480 335 408 2.1.
SM500MK4 Service Manual 154 2.1.
SM500MK4 Service Manual 2.
SM500MK4 Service Manual ON / OFF KEY * Turn display ON or OFF. NUMERIC KEYS To * Enter numeric data. TARE KEY * Set or Clear Tare Value. * Select " NO " in S and Z Mode. * Item Test print in S Mode. CLEAR KEY * Clear numeric values. * Select " YES " in S and Z Mode. RE-ZERO KEY * Reset weight to zero. PRE-PACK KEY * Switch Manual mode and Pre-pack mode alternatively. (The mode status will be indicated in the P and M indicator.
SM500MK4 Service Manual VOID KEY * Correct the Sales Data PLU KEY * Call up PLU data. * Store the programmed data in S mode. FEED KEY * Feed Label or Receipt PRINT KEY * Print out Label or Receipt MODE SELECT KEY * Five Modes can be selected using this key. Indicator R - REGISTRATION MODE (All the sales transactions are performed.) Indicator X - CHECK MODE (Printing out and sales report.) Indicator S - PROGRAM MODE (Programming preset data, such as products, data, shop name, etc.
SM500MK4 Service Manual 2.3 Panel Layout Bench and Pole Type (For 300 LCD) There are fifteen different indicators on Display Panel as shown below. 1. Î0Í : Lights when scale is stable at the zero point 2. NET : Lights when tare subtraction in performed. 3. P : Lights when PRE-PACK Mode is selected. 4. MAN : Lights when MANUAL Mode is selected. 5. AM : Lights when the amount is displayed. 6. CH : Lights when the amount of change is being displayed. 7.
SM500MK4 Service Manual 3. SPANSWITCH 3.1 Span Switch Jumper Setting Changing Procedure Interface Board Cable 1. Bottom View of Machine. 2. Loosen the 4pcs SEMS B screw M4X6, then open the Bottom Cover. 3. Loosen the 2pcs Truss Head screw M4X6, and disconnect the Interface Board cable. Insulator 4. Loosen the 2pcs SEMS B screw M3X6, then open the Insulator. 3.2 5. Change [SW2] jumper to Enable/Disable Span Switch.
SM500MK4 Service Manual 4. INITIALSETUP 4.1 4.1.1 Scale Assembly Display Pole Kit Mounting 1. Place the display Pole inside the pole bottom (base AB) 2. Align the four holes of the display pole and tighten screw Flat Head M4x16 4.1.2 Level Adjustment Place the scale on the flat surface and adjust the four legs until the bubble on the level is in the center as shown above. 4.2 4.2.1 Software Setting Memory Initialization There are two methods of memory initialization. 4.2.1.
SM500MK4 Service Manual KEY TO PRESS [0] To OPERATION -- Select scale type. [8] OR -- Select scale type. & Then -- To set the scale type. KEY TO PRESS [0] To Scale Type: 0: Pole 6 Kg 1: Pole 15 Kg 2: Pole 30 Kg 3: Pole 30 Lb 4. Bench 6 Kg 5: Bench 15 Kg 6: Bench 30 Kg 7: Bench 30 Lb 8: Printer (BP 80/90) OPERATION -- Select label length. [1] -- Select label length. Label Length: 0: Short ÆLabel length up to maximum 120mm. -- To set the label length.
SM500MK4 Service Manual Key to press Operation -- Process of initialize. -- Then go to segment check. If Yes, PLEASE WAIT Key to press Operation -- Go to segment check. If No, 4.2.1.2 Default Country Specification 1 Key to press Operation [9] + [3] Switch On the Power. -- Show current country SPEC then default Customer Specification setting. -- Follow the instruction: a) Press the [Clear] then b) Press the [Print] process to next step KEY TO PRESS OPERATION -- Select label length.
SM500MK4 Service Manual Key to press Operation -- Reading Country Specification. Key to press Operation -- After Reading Country Spec, the display will prompt MEMORY CLEAR message. Key to press If Yes, press If No, press Operation -- Process of initialize. -- Then go to segment check. OR -- Go to segment check.
SM500MK4 Service Manual 4.3 Calibration Key to press In the Weighing Mode, press then turn On the Span Switch. Operation -- Go to Z mode KEY TO PRESS + [8][7][1][5] OPERATION -- Access code to calibration mode. KEY TO PRESS OPERATION -- To calibrate zero point. -- Ensure no weight in platter -- Wait until the ‘ SET WEIGHT & PRT ’ shows KEY TO PRESS Place the capacity weight on the scale after the following screen appears.
SM500MK4 Service Manual 4.4 User Spec Setup Procedure To Change the setting of the User SPEC, if there is some SPEC need to alter. KEY TO PRESS OPERATION In the Weighing Mode, press then turn On the Span Switch. -- Go to Z mode.
SM500MK4 Service Manual KEY TO PRESS OPERATION -- Decrease the SPEC number without saving data of the previous SPEC number. KEY TO PRESS OPERATION -- To jump to desire SPEC number. [1][0] KEY TO PRESS OPERATION Save SPEC setting and Exit to R mode. OR Do not save SPEC setting and Exit to R mode.
SM500MK4 Service Manual 4.5 Weigh & Measurement Spec Setup Procedure To Change the setting of the Weight & Measurement SPEC, if there is some SPEC need to alter. KEY TO PRESS OPERATION In the Weighing Mode, press then turn On the Span Switch. -- Go to Z mode KEY TO PRESS OPERATION -- Go to Weight and Measure Specification Mode -- To change the selection for the Spec, press the Number of the selection.
SM500MK4 Service Manual KEY TO PRESS OPERATION -- Decrease the SPEC number without saving data of the previous SPEC number. KEY TO PRESS OPERATION -- To jump to desire SPEC number. [6][1][0] KEY TO PRESS OPERATION Save SPEC setting and Exit to R mode. OR Do not save SPEC setting and Exit to R mode. Remarks: Please restart the scale every time after changing the SPEC.
SM500MK4 Service Manual 5. HARDWARETESTING&MAINTENANCE 5.1 Hardware Testing KEY TO PRESS OPERATION -- Go to Z mode In the Weighing Mode, press 5.1.1 RAM Read and Write Test KEY TO PRESS + [0] OPERATION -- Go to Hardware Testing Mode and first it will show the RAM TEST Result [0] [1] KEY TO PRESS OPERATION -- If the RAM is Ok, It will show the message below. OR -- If the RAM is Fail, It will show the message below.
SM500MK4 Service Manual 5.1.2 SIO Loop Back Test KEY TO PRESS OPERATION -- Testing the RS232 port. -- Please plug in the connector on the RS232C port before proceed. (The test result is show at below). OR 5.1.3 RS485 Loop Back Test KEY TO PRESS OPERATION -- Testing the 4-Line port. -- Please plug in the test connector on the 4-Line port before proceed. (The test result is show at below) OR 5.1.4 Ethernet Loop Back Test KEY TO PRESS OPERATION -- Testing the Ethernet port.
SM500MK4 Service Manual 5.1.5 ROM Checksum Test KEY TO PRESS OPERATION -- Testing the ROM Checksum. -- Press the [PRINT] Key to start the testing. After that FF5A5B 5.1.6 PLU Generator Test KEY TO PRESS OPERATION -- Testing the PLU Generator. -- Press the [PRINT] key to start PLU Generator. + Then it will display how many PLU generated at the right top corner.
SM500MK4 Service Manual KEY TO PRESS OPERATION -- Exit to Z mode. Remarks: 5 4 1 6 TEST JIG CONNECTOR for SIO Port Connect pin 4 and pin 5 5.1.7 TEST JIG CONNECTOR for 4 LINE RS485 Port Connect pin 1 and pin 3 Connect pin 2 and pin 4 Internal Count KEY TO PRESS In the Weighing Mode, press OPERATION . -- Go to Z mode. -- Then turn on the Span Switch.
SM500MK4 Service Manual 5.1.8 Span Switch Status KEY TO PRESS OPERATION In the Weighing Mode, press . -- Go to Z mode. -- Then turn on the Span Switch. KEY TO PRESS + 5.2 OPERATION -- Indicates SPAN Switch status. -- Back to Z mode, after 1 second. [2][8][4] Adjustment 5.2.1 Location of Gap Sensor And Peel Sensor. 5.2.2 Label Gap Sensor The label sensor is to detect the gap between the labels so as to identify the starting position of the label.
SM500MK4 Service Manual 5.2.3 Peel Sensor To set the peel sensor voltage if the peel sensor is not working normally in some situations like temperature and humidity changed. The peel sensor voltage can be set automatically by press the # key. KEY TO PRESS OPERATION -- At R mode. KEY TO PRESS OPERATION -- Go to the Peel sensor adjustment. + [5][1][5] KEY TO PRESS OPERATION -- Once the key is press, it will auto set the voltage value and Exit to R mode.
SM500MK4 Service Manual 5.2.4 Printing Position To adjust the printing position when printing is out of alignment. The process only allows adjusting vertical position only. KEY TO PRESS OPERATION -- At R mode. KEY TO PRESS + OPERATION -- Go to Thermal Head calibration. [5][1][4] KEY TO PRESS OPERATION -- Adjust upward. [2][0] OR -- Adjust downward. [2][0] OR -- Store new value and Exit to R mode.
SM500MK4 Service Manual 5.3 Maintenance 5.3.1 Thermal Head Cleaning To maintain good quality printouts and long life span for the thermal print head, regular cleaning of the thermal print head is required. Please use the cleaning kit supplied with the product. Instruction 1. Turn OFF Scale by Main Power Switch. 2. Open the Printer Side Door first, after that press on the top of Printer Front Door and pull out the cover toward in front. Printer Side Door Printer Front Door 3.
SM500MK4 Service Manual 4. Use the tip of the Cleaning Tool to clean the Thermal Head portion as shown: Thermal Head Cleaning Tool CAUTION Use only the cleaning pen from the provided cleaning kit Do not clean or try to remove dirt or anything sticking on thermal head with sharp objects – this will DAMAGE the thermal print head. 5. After Finish cleaning press down the Printer Head Handle first, then close the Printer Front Door and Printer Side Door. 6.
SM500MK4 Service Manual 5.3.3 Thermal Head cleaning and replacement Printer Side Door Printer Head Handle Printer Front Door 1. Open the Printer Side Door. 2. Press on the top of Printer Front Door and pull out the cover toward in front. 3. Push the Printer Head Handle to up for Printer Head in upper position. 4. Need to take out the Thermal Head wire. 5. Use the Hand push the Thermal Head to up first then pull out the thermal head. (Because the thermal head bracket catch by printer head bracket).
SM500MK4 Service Manual 5.4 Method of Assembly Sealing Screw & Sticker 5.4.
SM500MK4 Service Manual 5.4.
SM500MK4 Service Manual 6. DISASSEMBLY 6.
SM500MK4 Service Manual 105 106 108 105 106 108 109 108 108 109 107 110 111 112 110 110 111 112 110 112 112 Screw Type : 105- Sems B M4X8 (2pcs) 106- Sems B M3X8 (2pcs) 107- Flat Head M4X16 (1pcs) 108- Truss Head M4X16 (4pcs) 109- Sems B M4X6 (2pcs) 110- Sems B M3X6 (4pcs) 111- Binding Head M3X8 (2pcs) 112- Allen Cap M6X20 (4pcs) 34
SM500MK4 Service Manual 114 Ground Wire 114 113 113 113 115 115 114 115 Screw Type : 113- Sems B M4X8 (2pcs) 114- Sems B M4X6 (4pcs) 115- Sems B M4X12 (3pcs) 35 114
SM500MK4 Service Manual 6.2 AD Board Disassembly 101 101 Loadcell wire color indication Green Blue White Red Black Screw Type : 101- Sems B M3X6 (2pcs) 1. To remove the AD Board, solder out the Loadcell wire and then unscrew the 2pcs Sems B M3X6 screw.
SM500MK4 Service Manual 6.3 Loadcell Disassembly 101 101 Support AA Loadcell Screw Type : 101 101 101- Allen Cap M4X20 1. 2. To remove the Support AA from Loadcell, unscrew the 2pcs Allen Cap screw M4X20 from Top. To remove the Loadcell from Base Diecast, unscrew the 2pcs Allen Cap screw M4X20 from Bottom.
SM500MK4 Service Manual 6.4 Extra Bracket Disassembly for 30Kg 101 101 Screw Type: 101 101- M4 X 12 Sems B 101 1. To assembly the Bracket EE (30KG, Base Top) tighten 1pcs Sems B screw M4x12 from Top. 2. To assembly the Bracket EF (30KG, Base Bottom) tighten 3pcs Sems B screw M4x12 from Bottom.
SM500MK4 Service Manual 7. FIRMWAREUPGRADE 7.1 Boot loader Downloading The software use for Boot loader downloading to scale is Flash Development Toolkit 3.1. 1. PC to scale via RS232C interface. RS232 Cable 1) Double click open the [Flash Development Toolkit 3.1] software. 2) When Option icon appears, click the [Cancel]. 3) From the Option Menu, select the [File Æ Open An S-Record…].
SM500MK4 Service Manual 4) Click the [bootloader23MH.mot] file from the location where you put and then click the [Open]. 5) From the Option Menu select the [Device] Æ [Configure Flash Project]. 6) Click the to select the device [H8/3024F]. 7) Click the to select the port [COM1], then click the . 8) In the CPU crystal frequency for selected device, change the default number 25 to [23], then click the 2 time. Note: Enter the number 23, it will automatically change to number [23.0000].
SM500MK4 Service Manual 9) Click the . 10) From the Option Menu select [Device] Æ [Download Active File]. 11) After boot loader downloading finish, on the screen will shown [Main kernel download complete… Connection Complete]. Note: Ensure that after downloading completed, must change back the Mainboard [SW 1] jumper setting.
SM500MK4 Service Manual 7.2 Firmware Downloading The software use for firmware downloading to scale is Hyper Terminal. 1. PC to scale via RS232C interface. 2. Plug in the Power Cord connect to Scale. (Don’t on the power first) RS232 Cable 1) From the Windows XP software, select Start Æ All Programs Æ Accessories Æ Communications Æ Hyper Terminal. 2) Once screen appear Connection Description setting.
SM500MK4 Service Manual 4) In the Hyper Terminal software to select [File] Æ [Properties] to open the properties setting. 5) Go to Settings Option use the by below highlight as shown. button to change the setting follow Emulator: ANSIW Telnet terminal ID: VT100 Click the [OK] button to exit and go to downloading page. 6) Switch on the scale power, the screen will shown [Press any key to enter SM300/500 Basic Boot-loader], then press the keyboard [Enter] key button 2 times.
SM500MK4 Service Manual 8) a) After next step on the screen shown [Enter erase end address as a 32-bit hex value e.g. AABBCC]. b) Type in number & character [00beffff], it will shown the information of Confirm erase block (Y/N). c) Press the “Y” keyboard button, it will automatically to start erase the blocks data. d) Need to take time waiting around 5 minutes for process. 9) a) After Blocks data erase, the screen will go back to SM300/500 Basic Bootloader Main Menu.
SM500MK4 Service Manual 12) Select the Software/File where the software/file allocate, and then click the [Open] button. 13) When the screen appear Send File page, click the [Send] button. Note: Ensure the [Protocol] option, using to select [1K Xmodem] 14) The downloading and upgrade the software needs to take time waiting around 15 minutes for process. 15) When the screen shown [Upload Ok] and automatically goes back to Main Menu, that meaning the downloading/upgrade the software is completed.
SM500MK4 Service Manual 8. HARDWARESETTING 8.1 Main Board Jumper Setting Below is Main Board jumper setting for SM500MK4 using 300 LCD, If the jumper setting wrongly to set, the display will not function/working properly. Both LCD (Operator and Customer) are using 300LCD, then follow the below table Type of LCD JP4 JP5 300LCD Short 2 & 3 Short 2 & 3 Note: This setting is Default Setting for SM500MK4 Main Board. 9. MISCELLANEOUS 9.1 Error Messages Error No.
SM500MK4 Service Manual 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 DEPARTMENT NOT EXIST TAX FILE NOT EXIST CLERK NOT EXIST PLEASE PRESS PLU KEY DATE INVALID TIME INVALID FUNCTION NOT EXIST KEY NOT ASSIGN KEY ALREADY ASSIGNED LOGO NOT EXIST LABEL INVALID PLU NOT AVAILABLE DATA INVALID QUANTITY OVERFLOW NO LINK SYSTEM ERROR VERIFY ERROR TIME ERROR BELOW MIN WEIGHT REC CHOSEN USED IN MG
SM500MK4 Service Manual 9.2 Corresponding Key of IBM Keyboard The IBM keyboard can directly connect to the SM500MK4 in the IBM keyboard port at the bottom of the scale. It can only function when in the S mode (Programming mode). And the IBM keyboard wire connector must using PS2 connector. IBM KEYBOARD F1 F2 F3 F4 F6 F7 ENTER BACKSPACE ← → ↑ ↓ DEL INS CAPS LOCK 9.
SM500MK4 Service Manual REMARKS: 9.4 The small letter only can print at label but cannot print at receipt. TERAOKA Code The table shown below is the common use of characters of TERAOKA code in numerical value. Please enter the numerical value when entering commodity name, advertisement, shop name, clerk name, special message, ingredient, text etc. when using the SM 500MK4 BENCH TYPE.
SM500MK4 Service Manual Cross Cable Connection Straight Cable Connection SCALE PIN SIGNAL 1 TX+ HUB SIGNAL PIN TX+ 1 SCALE / HUB PIN SIGNAL 1 TX+ SCALE / HUB SIGNAL PIN RX+ 3 2 TX- TX- 2 2 TX- RX- 6 3 RX+ RX+ 3 3 RX+ TX+ 1 6 RX- RX- 6 6 RX- TX- 2 5,7,8 N.A. N.A. 5,7,8 5,7,8 N.A. N.A. 5,7,8 9.5.2 Cash Drawer Option (RJ11) SM-500MK4 SCLAE SIDE (Interface Board) 4 5 6 1 2 3 Note: This connector is used for Interface Board TWB-01750-1.
SM500MK4 Service Manual 9.5.3 PS2 Keyboard Option PS2 IBM Keyboard Connector (Main Board Side) 6 5 4 3 1 2 Pin Signal 1 DATA 2 NC 3 GND 4 VCC 5 CLK 6 NC 9.5.
SM500MK4 Service Manual PC (9 PIN) TO LCU 401 (FOR PC to LCU 401 communication) 9 Pin D-Sub (Female) Pin 1 2 3 4 5 6 7 8 9 25 Pin D-Sub (Male) Signal Signal CD RXD TXD DTR GND DSR RTS CTS CI CD RXD TXD DTR GND DSR RTS CTS CI Pin 8 3 2 20 7 6 4 5 22 PC (25 PIN) TO LCU 401 (For PC to LCU 401 communication) 25 Pin D-Sub (Female) Pin 2 3 4 5 6 7 8 20 22 25 Pin D-Sub (Male) Signal Signal TXD RXD RTS CTS DSR GND CD DTR CI TXD RXD RTS CTS DSR GND CD DTR CI 52 Pin 2 3 4 5 6 7 8 20 22
SM500MK4 Service Manual SCALE TO SCALE (For LCU 401 to scale and scale-to-scale communication) SM300 / SM80SX / SM90 / SM500 / SM500MK4 9 Pin D-Sub (Male) Pin REMARKS: 9 Pin D-Sub (Male) Signal 1 2 3 4 5 to 8 9 SM300 / SM80SX / SM90 / SM500 / SM500MK4 Signal IN IN OUT OUT N.C. GND IN IN OUT OUT N.C. GND Pin 1 2 3 4 5 to 8 9 Please solder the FG (Film Ground) of the cable to the metal casing of the connector for more isolation to noise.
SM500MK4 Service Manual PC (9 PIN) TO SCALE RS232C PORT (For PC and PC FL-1 communication) SM300 / SM80SX / SM90 / SM500 / SM500V2 / SM500MK4 RS232 Port 9 Pin D-Sub (Female) Pin 8 Pin DIN plug (Male) Signal Signal Pin 3 TXD RXD 4 2 RXD TXD 5 5 GND GND 2 7 RTS RTS 6 8 CTS CTS 7 1 CD DSR 3 6 DSR 4 DTR 54
SM500MK4 Service Manual 10. APPENDIX 10.1 Block Diagram 10.1.
SM500MK4 Service Manual 10.1.
SM500MK4 Service Manual 10.1.
SM500MK4 Service Manual 10.2 Specification List 10.2.
SM500MK4 Service Manual SPEC 7: SELECTION OF TOTAL BARCODE 0: F1F2 CCCCC XCD XXXX (13 DIGIT NON-PLU) 1: F2 CCCCCC XCD XXXX (13 DIGIT NON-PLU) 2: F1F2 CCCCC O XXXX (13 DIGIT NON-PLU) 3: F1F2 CCCCCC XXXX CD (13 DIGIT NON-PLU) 4: F1F2 CCCCC XXXXX CD (13 DIGIT NON-PLU) 5: F2 CCCCCC XXXXX CD (13 DIGIT NON-PLU) 6: F2 CCCCC XXXXXX CD (13 DIGIT NON-PLU) 7: F1F2 CCCCCCCCCC CD (13 DIGIT PLU) 8: F1F2 CCCC XXXXXX CD (13 DIGIT NON-PLU) 9: F1F2 CCCCC CD (8 DIGIT PLU) 10: F2 CC XXXX CD (8 DIGIT NON-PLU) 11: NON BARCODE (N
SM500MK4 Service Manual SPEC 15: SELECTION OF TURN OVER PRINTING FOR ADV MESSAGE 0: NO 1: YES SPEC 16: EXIT FROM ' CHANGE ' MODE WITHIN SPECIFIED INTERVAL 0: NO 1: 3 SECOND 2: 6 SECOND 3: 10 SECOND 4: 15 SECOND SPEC 17: SELECTION OF ORDERING MONTH, DATE AND YEAR FOR PRINT 0: M / D / Y 1: D / M / Y 2: Y / M / D 3: NOT USED SPEC 18: SELECTION OF 1 / 2 LINE ( S ) COMMODITY NAME ON RECEIPT 0: 2 LINES 1: 1 LINES SPEC 19: LABEL PRINTING BY CLERK KEY 0: NO PRINT 1: PRINT WITH ACCUMULATION 2: PRINT WITHOUT ACCUMULA
SM500MK4 Service Manual SPEC 25: SELECTION OF DEFAULT LABEL FORMAT FOR TOTAL PRINTING STANDARD U1,CA STANDARD U1,CA 0: T1 A 12: S T7 1: T2 B 13: A T8 2: T3 C 14: B T9 3: T4 U2 15: C T10 4: T5 U3 16: F1 F1 5: T6 U4 17: F2 F2 6: T7 U5 18: F3 F3 7: T8 U6 19: F4 F4 8: T9 U7 20: F5 F5 9: T10 U8 21: F6 F6 10: T11 T5 22: F7 F7 11: T12 T6 23: F8 F8 SPEC 26: SELECTION OF SHOP NAME PRINTING ON LABEL 0: NO PRINT 1: PRINT SPEC 27: FORCED TARE FUNCTION 0: DISABLE 1: ENABLE SPEC 28: SELECTION OF PEEL SENSOR FUNCTION IN P
SM500MK4 Service Manual SPEC 38: SELECTION OF RECEIPT PRINT DENSITY 0: LOW 1: MID 2: H. MID 3: HIGH SPEC 39: SELECTION OF PLU CALLING 0: MANUAL 1: AUTO 2: TIME-OUT SPEC 40: SELECTION OF PLU DIGITS FOR AUTO PLU TIME OUT CALLING 0: 3 DIGITS/0.5 SEC 1: 4 DIGITS/1.0 SEC 2: 5 DIGITS/1.5 SEC 3: 6 DIGITS/2.0 SEC SPEC 41: U.
SM500MK4 Service Manual SPEC 52: SELECTION OF DATA LENGTH ( SIO ) 0: 7 BIT 1: 8 BIT SPEC 53: SELECTION OF PARITY ( SIO ) 0: NONE 1: ODD 2: EVEN SPEC 54: SELECTION OF STOP BIT ( SIO ) 0: 1 BIT 1: 2 BIT SPEC 55: SELECTION OF BAUD RATES FOR MULTI-DROP SIO 0: 1200 1: 2400 2: 4800 3: 9600 4: 19200 5: 38400 SPEC 56: SELECTION OF DATA LENGTH FOR MULTI-DROP SIO 0: 7 BIT 1: 8 BIT SPEC 57: SELECTION OF PARITY FOR MULTI-DROP SIO 0: NONE 1: ODD 2: EVEN SPEC 58: SELECTION OF STOP BIT FOR MULTI-DROP SIO 0: 1 BIT 1: 2 BI
SM500MK4 Service Manual SPEC 65: REPORT PRINTING IN DAILY AND TERM TRANSACTION CLEAR 0: INHIBIT 1: ALLOW SPEC 66: PACK QUANTITY FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 67: ADVERTISEMENT FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 68: FIXED TOTAL PRICE DISCOUNT FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 69: TOTAL PRICE PERCENTAGE DISCOUNT FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 70: FIXED UNIT PRICE FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 71: FIXED UNIT PRICE PERCENTAGE FUNCTION KEY ENABLE
SM500MK4 Service Manual SPEC 81: PRINT SELECT FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 82: PRINT OF PLACE OF PRODUCTION ON LABEL 0: INHIBIT 1: ALLOW SPEC 83: SELECTION OF MARKDOWN 0: NO MARKDOWN 1: UNIT PRICE MARKDOWN 2: TOTAL PRICE MARKDOWN 3: UNIT AND TOTAL PRICE MARKDOWN SPEC 84: SUB-TOTAL FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 85: GRAND-TOTAL FUNCTION KEY ENABLE 0: ALLOW 1: INHIBIT SPEC 86: SELECTION OF LABEL SENSOR GAP VALUE (0 – FF) SPEC 87: SELECTION OF LABEL TYPE 0: GAP 1: NO GAP SPEC 88:
SM500MK4 Service Manual SPEC 96: SELECTION OF ADVERTISEMENT MESSAGE ON ALL LABELS 0: INHIBIT 1: ALLOW SPEC 97: SELECTION OF MANUAL PRINT IN PREPACK MODE FOR WEIGH ITEM 0: INHIBIT 1: ALLOW SPEC 98: SELECTION OF QUANTITY AND UNIT PRINTOUT FOR NON-WEIGH ITEM IN MANUAL MODE 0: ALLOW 1: INHIBIT SPEC 99: SELECTION OF UNIT PRINTOUT FOR NON-WEIGH ITEM IN MANUAL MODE 0: INHIBIT 1: ALLOW SPEC 100: SELECTION OF DISCOUNT IN PLU PROGRAMMING 0: ALLOW 1: INHIBIT SPEC 101: SELECTION OF ZERO SUPPRESS FOR DATE AND TIME 0: NO
SM500MK4 Service Manual SPEC 111: SELECTION OF PRICE SYMBOL ON RECEIPT (FOR AA ONLY) 0: NO PRINT 1: KANJI YEN 2: YEN SPEC 112: DEFAULT DATA OF PRINTING SPECIAL MESSAGE NUMBER FOR RECEIPT (0 - 16) SPEC 113: SELECTION OF LABEL LOGO PRINTING STATUS 0: NO PRINT 1: LOGO 1 2: LOGO 2 3: LOGO 3 4: LOGO 4 SPEC 114: SELECTION OF RECEIPT LOGO PRINTING STATUS 0: NO PRINT 1: LOGO 1 2: LOGO 2 3: LOGO 1 & LOGO 2 4: LOGO 3 5: LOGO 4 6: LOGO 1, 2, 3 & 4 SPEC 115: SELECTION OF TYPE OF ENTRY FOR USED-BY-DATE AND SELL-BY-DATE
SM500MK4 Service Manual SPEC 125: POSITION OF SPECIAL MESSAGE ON RECEIPT 0: BOTTOM OF RECEIPT 1: TOP OF RECEIPT SPEC 126: SELECTION OF FUNCTION KEYS PROTECTION FOR DENMARK SELF -SERVICE 0: NO PROTECTION 1: PROTECTION 2: PARTIAL PROTECTION SPEC 127: SELECTION OF PRINTING OF CHECKSUM FOR ITEM BARCODE 0: DISABLE 1: ENABLE SPEC 128: SETTING OF HOST NUMBERS (1 – 9999) SPEC 129: TYPE OF HOST TO BE COMMUNICATED 0: STANDALONE 1: TMR ECR 2: POS ECR SPEC 130: SELECTION OF PRINT ITEM ON PREPACKS TOTAL LABEL 0: BASED O
SM500MK4 Service Manual SPEC 141: SELECTION OF YEAR FORMAT 0: YY 1: YYYY SPEC 142: SELECTION OF DAY DISPLAY FOR SELL-BY-DATE 0: DISABLE 1: ENABLE SPEC 143: PEEL SENSOR TRIGGER VOLTAGE 0: HIGH 1: LOW SPEC 144: DISPLAY PREPACKS QUANTITY BALANCE 0: ENABLE 1: DISABLE SPEC 145: PRINT SELECT FUNCTION ACROSS THE BOARD 0: DISABLE 1: ENABLE SPEC 146: SELECTION OF LABEL FORMAT 1, 2 FUNCTION KEY ENABLE (AR) 0: DISABLE 1: ENABLE SPEC 147: SELECTION OF PREPACK NON ADD FUNCTION KEY ENABLE (NOT FOR AA) 0: DISABLE 1: ENABL
SM500MK4 Service Manual SPEC 157: TRAINING MODE 0: DISABLE 1: ENABLE SPEC 158: FSD PRICE AND IMAGES 0: DISABLE 1: ENABLE SPEC 159: ½ AND ¼ KEY ENABLE 0: DISABLE 1: ENABLE SPEC 160: TWISTED PAIR CABLE FOR ETHERNET 0: SHIELDED 1: UNSHIELDED SPEC 161: DISCOUNT LABEL FORMAT (SWEDEN) 0: ENABLE 1: DISABLE SPEC 162: SELECTION OF ITEM CODE FUNCTION KEY ENABLE 0: ENABLE 1: DISABLE SPEC 163: SELECTION OF TRANSACTION DATA STORE IN CLIENT MEMORY 0: DISABLE 1: ENABLE SPEC 164: MAXIMUM LABEL LENGTH 0: 120 MM 1: 240 MM SP
SM500MK4 Service Manual SPEC 173: MASK 7 SEGMENT DISPLAY IN X, S, and Z MODE 0: NO 1: YES SPEC 174: FIXED CLERK ASSIGN TO PRESET KEYS 8/ 16/ 24/ 32 (BENCH TYPE ONLY) 0: CLERK KEYS 1: FUNCTION KEYS SPEC 175: 30LB → 15KG CONVERSION (UK) 0: DISABLE 1: ENABLE SPEC 176: DISCOUNT TIME ON DAILY BASIS 0: NO 1: YES SPEC 177: WEIGHT CHECK FUNCTION 0: NO 1: YES SPEC 178: UNIT PRICE OVERRIDE PER PLU 0: NO 1: YES SPEC 179: BLACK BAR SENSING LABEL 0: NORMAL 1: BLACK BAR SENSING SPEC 180: SCROLL MESSAGE GROUP 0: DISABLE 1
SM500MK4 Service Manual SPEC 189: PLU AUTO DELETE 0: NO DELETE 1: 15 DAYS 2: 30 DAYS 3: 90 DAYS SPEC 190: SWAP WEIGHT AND 0: NO 1: YES UNIT PRICE ON RECEIPT SPEC 191: DEFAULT ITEM CODE EQUALS TO PLU NUMBER 0: NO 1: YES SPEC 192: NUTRITION TEMPLATE 0: STANDARD 1: SIMPLIFIED 2: SIMPLIFIED CONDENSED 3: STANDARD CONDENSED 4: TABULATED 5: TABULATED EXTRA CONDENSED SPEC 193: NUTRITION ADJUSTMENT FEED (0 – 255) SPEC 194: SERVER IP ADDRESS (1 – 254) SPEC 195: WEIGHT PRINT FOR NON-WEIGH ITEM 0: NO 1: YES SPEC 196:
SM500MK4 Service Manual SPEC 204: REFERENCE PLU FUNCTION KEY ENABLE 0: DISABLE 1: ENABLE SPEC 205: PRINT FUNCTION KEY ENABLE 0: DISABLE 1: ENABLE SPEC 206: PRINT BARCODE WHEN RIGHT SIDE WEIGHT DATA OVERFLOW 0: NO PRINT 1: PRINT BARCODE DIGITS SPEC 207: SELECTION OF WEIGHT DECIMAL POINT POSITION FOR BARCODE AND LABEL PRINTING 0: SAME AS SPEC 607 1: 0.
SM500MK4 Service Manual SPEC 218: ZERO UNIT PRICE FOR UNIT PRICE CHANGE FUNCTION KEY 0: DISABLE 1: ENABLE SPEC 219: NUMERIC KEY ENTRY RESET (AA) 0: 3 SECONDS 1: 5 SECONDS 2: DISABLE SPEC 220: ITEM BARCODE RIGHT SIDE DATA DEPENDENT ON UNIT 0: DISABLE 1: ENABLE SPEC 221: RECEIPT WITH TAX INFORMATION FUNCTION KEY ENABLE 0: DISABLE 1: ENABLE SPEC 222: OPEN CASH DRAWER WITHOUT SALES FUNCTION KEY ENABLE 0: DISABLE 1: ENABLE SPEC 223: NEGATE UNIT PRICE FUNCTION 0: DISABLE 1: ENABLE SPEC 224: FIS3000 CABLE 0: 4 WIR
SM500MK4 Service Manual SPEC 234: SUB-TOTAL AND GRAND TOTAL BARCODE 0: BASED ON ITEM BARCODE 1: BASED ON TOTAL BARCODE SPEC 235: MASK BARCODE LAST HUMAN READABLE CHECK DIGIT 0: NO 1: YES SPEC 236: CHARACTER GENERATOR FOR KOREA 0: OLD 1: NEW SPEC 237: HALF KEY FUNCTION 0: INHIBIT 1: ALLOW SPEC 238: FIS3000 FREE FORMAT UNIT 0: MM 1: DOTS 2: SM-25 DOTS SPEC 239: CHEQUE & CREDIT PAYMENT FUNCTION KEY 0: DISABLE 1: ENABLE SPEC 240: VOUCHER PAYMENT FUNCTION KEY 0: DISABLE 1: ENABLE SPEC 241: PLU CODE FOR IR POS &
SM500MK4 Service Manual SPEC 249: PRINT USED BY DATE 0: MANUAL AND PREPACK MODE 1: MANUAL MODE 2: PREPACK MODE 3: NO PRINT SPEC 250: CENTERING SHOP NAME ON LABEL 0: NO CENTERING 1: CENTERING SPEC 251: SHOP NAME ON RECEIPT 0: TOP 1: BOTTOM SPEC 252: AUTO RECONNECT WHEN SERVER DOWN 0: NO AUTO RECONNECT 1: RECONNECT EVERY 2 MIN 2: RECONNECT EVERY 3 MIN 3: RECONNECT EVERY 15 SECONDS SPEC 253: CLIENT AUTO PLU UPDATE 0: UPDATE /DELETE EXISTING PLUs 1: UPDATE /DELETE ALL SERVER PLUs 2: UPDATE EXISTING PLUs (NO DEL
SM500MK4 Service Manual SPEC 263: FSD NET VALUE MINIMUM 0: OFF 1: ON SPEC 264: PRINT INGREDIENT DATA ON THE NEXT LABEL 0: DISABLE 1: ENABLE SPEC 265: CLIENT USING LOCAL FREE FORMAT LABEL 0: NO 1: YES SPEC 266 : FSD WEIGHT 0: BACK COMPUTED (SINGLE RANGE) 1: BACK COMPUTED (DUAL RANGE) 2: EXACT WEIGHT SPEC 267: CPDL LANGUAGE SELECTION 0: 1ST LANGUAGE 1: 2ND LANGUAGE SPEC 268: DISPLAY SPECIAL SCALE MSG FOR DISCOUNTED ITEM (SM90) 0: NO 1: YES SPEC 269: AUTO CLERK ACCUMULATION 0: NO 1: 9995 (A KEY) 2: 9996 (B KEY
SM500MK4 Service Manual 4: 5 DAYS BUFFER 5: 6 DAYS BUFFER 6: 7 DAYS BUFFER UNLIMITED BUFFER SPEC 278: TRACEABILITY REPORT 0: DISABLE 4: BY REFERENCE NUMBER 5: BY PLU NUMBER 6: BY DATE & REF NUMBER 7: BY DATE & PLU NUMBER SPEC 279: U1 SELF SERVICE 0: DISABLE 1: ENABLE SPEC 280: REAL TIME CUSTOMER NUMBER 0: NO 1: YES SPEC 281: REAL TIME BUFFER RECEIPT 0: DETAIL 1: TOTAL ONLY SPEC 282: BARCODE FUNCTION 0: WITHOUT 1: WITH SPEC 283: NOT USED SPEC 284: OPEN CASH DRAWER ON CREDIT PAYMENT 0: ALLOW 1: INHIB
SM500MK4 Service Manual SPEC 293: SM200 POWER SAVE TIMEOUT 0: 3 MINUTES 1: 5 MINUTES 2: 10 MINUTES 3: 2 MINUTES SPEC 294: SM200 BATTERY OPTION 0: YES 1: NO SPEC 295: SM300 SCROLLING MSG UPDATE RATE 0: 6 LINE 1: 12 LINES SPEC 296: INGREDIENT FILE-SIZE EXPANSION 0: MAX 99 REC 1: MAX 255 REC SPEC 297: PRINT PLU INGREDIENT IN RCT 0: NO 1: YES SPEC 298: TRACEABILITY UPDATE FUNCTION 0: NO 1: YES SPEC 299: KEYBOARD SELECTION 0: NORMAL KEYBOARD 1: 100 PRESET KEYS KEYBOARD 2: 80 PRESET KEYS KEYBOARD SPEC 300: SM500
SM500MK4 Service Manual SPEC 310: RSS14 BARCODE (AI 01 ONLY) 0: DISABLE 1: ENABLE SPEC 311: OPERATOR LOGGING FUNCTION 0: DISABLE 1: ENABLE SPEC 312: CLERK ID/ PASSWORD (KE ONLY) / CHANGED PASSWORD (STANDARD) 0: DISABLE 1: ENABLE SPEC 313: UPDATE LOG FILE 0: CA+NO UPDATE FILE 1: CA+UPDATE FILE 2: KE+UPDATE FILE 3: KE+NO UPDATE FILE SPEC 314: TRAINING MODE 0: DISABLE 1: ENABLE 2: ENABLE (CLERK REPORT) SPEC 315: PRINT PLU TRACEABILITY IN RCT 0: YES 1: NO SPEC 316: INCLUDE PPK TTL IN MANUAL TTL RPT 0: NO 1: YES
SM500MK4 Service Manual SPEC 326: ON/OFF KEY 0: DISABLE 1: ENABLE SPEC 327: SM300 PRINT CONTROL 0: DISABLE 1: ENABLE SPEC 328: TU 9 DIG TOTAL PRICE 0: DISABLE 1: ENABLE SPEC 329: PLU TARE CALLS UP 0: ALLOW 1: INHIBIT SPEC 330: INDIVIDUAL SCALE STORE TOTAL REPORT 0: NO 1: YES SPEC 331: DEFAULT ITF FOR BARCODE 0: DISABLE 1: ENABLE SPEC 332: ITEM TEXT (5-16) PRINT ON TOTAL LABEL 0: DISABLE 1: ENABLE SPEC 333: IMAGE AT TOP RECEIPT (0 - 99) SPEC 334: IMAGE AT BOTTOM RECEIPT (0 - 99) SPEC 335: TRACEABILITY EATS B
SM500MK4 Service Manual SPEC 339: TRACEABILITY NO C/D CHECK 0: NO 1: YES SPEC 340: ENFORCE SCAN 0: NO 1: YES SPEC 341: TVP2000 0: NOT SEND T10 1: SEND T10 LABEL FORMAT SPEC 342: LCD 1 LINE SCROLL 0: DISABLE 1: ENABLE SPEC 343: CLEAR KEY IN PREPACK 0: ENABLE 1: DISABLE SPEC 344: PRINT PACK DATE 0: YES 1: NO SPEC 345: UPDATE SPEC FOR SERVER/CLIENT SYSTEM 0: ENABLE 1: DISABLE SPEC 346: UPDATE LABEL TURNOVER IN RT BUFFER 0: NO 1: ONLY IN REGISTRATION MODE 2: ONLY IN PRE-PACK MODE 3: REGISTRATION & PRE-PACK MODE
SM500MK4 Service Manual SPEC 355: CALL PLU FROM PC 0: DISABLE 1: ENABLE SPEC 356: EXPAND RECORD # FOR IMAGE 0: DISABLE 1: ENABLE SPEC 357: MULTI BARCODE FOR ITEM & TOTAL LBL 0: DISABLE 1: ENABLE SPEC 358: AUTO PRINT PER PLU 0: NO 1: YES SPEC 359: TOTAL PRICE BASED ON BARCODE (SF) 0: NO 1: YES SPEC 360: GENERIC BARCODE 0: NO 1: YES SPEC 361: TEXT COPY FROM FREE FORMAT 0: DISABLE 1: ENABLE SPEC 362: PRICE CALCULATION BASED ON GROSS WT 0: DISABLE 1: ENABLE SPEC 363: BARCODE READABLE CHARACTER 0: PRINT 1: NO PR
SM500MK4 Service Manual SPEC 605: SELECTION OF MANUAL SCALE 0: AUTO START 1: MANUAL START START SPEC 606: SELECTION OF ZERO LAMP LIGHTING POSITION 0: LIGHT ON AT GROSS ZERO ± 1 / 4 DIGIT 1: LIGHT ON AT NET ZERO ±1/4 DIGIT SPEC 607: SELECTION OF DECIMAL POINT POSITION FOR WEIGHT 0: NONE 1: 0.0 2: 0.00 3: 0.
SM500MK4 Service Manual SPEC 617: NEW AD 0: NO 1: YES SPEC 618: SELECTION OF NET / GROSS DUAL RANGE 0: GROSS DUAL RANGE METHOD 1: NET DUAL RANGE METHOD SPEC 619: SELECTION OF PLU WEIGHT ITEM COMMODITY NAME DISPLAY (BENCH TYPE) 0: FULL DISPLAY 1: HALF DISPLAY 2: NO DISPLAY SPEC 620: SELECTION OF TARE ACCUMULATION 0: ALLOW 1: INHIBIT SPEC 621: SELECTION OF TARE SUBTRACTION 0: ALLOW 1: INHIBIT SPEC 622: SELECTION OF MANUAL CLEAR OF TARE 0: ALLOW 1: INHIBIT SPEC 623: SELECTION OF WEIGHT RESET OPERATION DURING T
SM500MK4 Service Manual SPEC 632: SELECTION OF TARE VALUE EXCHANGE 0: ALLOW 1: INHIBIT SPEC 633: SELECTION OF AUTO CLEAR OF TARE 0: INHIBIT 1: ALLOW SPEC 634: SELECTION OF AUTO TARE CLEARS WHEN REZERO 0: INHIBIT 1: ALLOW SPEC 635: SELECTION OF TRIGGER POINT OF TARE / UNIT PRICE AUTO CLEAR 0: OVER NET 5d & OVER GROSS 21d & WEIGHT STABILITY 1: > = NET 1d AND WEIGHT STABILITY 2: > = NET 1d AND PRICE > 0 AND WEIGHT STABILITY SPEC 636: SELECTION OF AUTOMATIC ZERO RESET 0: INHIBIT 1: ALLOW SPEC 637: SELECTION OF
SM500MK4 Service Manual SPEC 646: SELECTION OF WEIGHT RANGE FOR PREPACK 0: OVER NET 5d & OVER GROSS 21d & WEIGHT STABILITY 1: OVER NET 1d AND WEIGHT STABILITY 2: OVER NET 19d AND WEIGHT STABILITY 3: OVER NET 20d AND WEIGHT STABILITY SPEC 647: SELECTION OF PLU TARE 0: ALLOW 1: INHIBIT SPEC 648: SELECTION OF ITEM PRINT WHEN TARE 0: ALLOW 1: INHIBIT SPEC 649: SELECTION OF TAX ROUNDING METHOD 0: ROUNDING 1: TRUNCATION SPEC 650: SELECTION OF CHECKING SPAN SWITCH FOR INTERNAL COUNT 0: NO CHECK 1: CHECK SPEC 651:
SM500MK4 Service Manual SPEC 661: SELECTION OF ADDITIONAL PRICE ROUNDING METHOD FOR TOTAL 0: NO ADDITIONAL ROUNDING 1: 1 / 4 ROUNDING 2: SPECIAL ROUNDING 3: ROUNDING FOR 1 ST DIGIT 4: CUT OFF 5: CUT UP 6: Υ5 CUT OFF AND Υ10 CUT OFF 7: DENMARK ROUNDING SPEC 662: SELECTION OF UNIT PRICE RE-CALCULATION 0: NO UNIT RE-CALCULATION 1: UNIT RE-CALCULATION SPEC 663: SELECTION OF NORDIC COUNTRY 0: INHIBIT 1: ALLOW SPEC 664: SELECTION OF DENMARK SELF SERVICE TYPE 0: INHIBIT 1: ALLOW SPEC 665: SWAP OF UNIT PRICE AND PR
SM500MK4 Service Manual SPEC 674: SELECTION OF MASKING LAST DIGIT OVER 15LB 0: NO 1: YES SPEC 675: AUTO ZERO ADJUSTMENT RANGE 0: ± 5d 1: 2% OF CAPACITY SPEC 676: SELECTION OF RIGHT SIDE BARCODE DATA RIGHT SHIFT FOR ITEM AND TOTAL BARCODE 0: NO RIGHT SHIFT 1: RIGHT SHIFT 2: RIGHT SHIFT TWICE 3: LEFT SHIFT TWICE 4: LEFT SHIFT 3 TIMES 5: LEFT SHIFT SPEC 677: MANUAL WEIGHT FUNCTION KEY 0: DISABLE 1: ENABLE SPEC 678: PRINTING OF ITEM LABEL AFTER WEIGHT CHANGE 0: INHIBIT 1: ALLOW SPEC 679: CATTY AND TAEL (TAIWAN
SM500MK4 Service Manual SPEC 687: PROPORTIONAL TARE 0: NO 1: YES SPEC 688: SM500 SELF-SERVICE 0: NO 1: YES SPEC 689: CONSECUTIVE COMMODITY NAME DISPLAY INTERVAL 0: 1 SEC 1: 2 SEC 2: 4 SEC 3: 6 SEC SPEC 690: TEST PROGRAM 0: DISABLE 1: ENABLE SPEC 691: ONE TOUCH TARE 0: ENABLE 1: DISABLE SPEC 692: SCROLLING MSG (SM300 ONLY) 0: NO 1: YES SPEC 693: FLEXI SELF SERVICE KEY GROUPING 0: NO 1: YES SPEC 694: WEIGHT HOLD FUNCTION (SM300) 0: DISABLE 1: ENABLE SPEC 695: CLERK PASSWORD SETTING (CA ONLY) 0: DISABLE 1: ENA
SM500MK4 Service Manual 10.2.
SM500MK4 Service Manual 11. REVISIONRECORDS REVISION RECORDS Serial no. Date Rev. Statu 001 Aug ‘06 00 Description of Changes 92 Software Version Remarks V29.
