Wavespeed/S WIRELESS SERIAL DEVICE Configuration Guide www.digi.
Table of Contents Wavespeed/S.......................................................................................... 3 Operating Modes.................................................................................... 3 Pre-Configuration .................................................................................. 3 User Configuration ................................................................................ 4 Serial Cable Replacement Configuration .....................................
Wavespeed/S The Wavespeed/S provides an easy-to-use wireless data solution for legacy applications providing a serial link (RS232) to transfer data between devices or between devices and a host. The serial cable can be replaced with a BluetoothTM wireless link that is transparent to the software application. Following initial configuration using a Windows ®-based Configuration Wizard, the Wavespeed/S takes on the specified DTE or DCE personality and port settings, providing a wireless data link.
User Configuration Serial Cable Replacement Configuration 1. Power both units and connect one to a serial port on your computer. 2. Place both units in configuration mode by sliding the three-position switch to the far right, away from the power connector. Class 1 units will need to be separated by several feet. 3. Launch the WvsdpCfg configuration utility. 4. In the first screen, select Cable Replacement. Select COM Port 5. 6.
10. The Configuration Wizard automatically notifies you that the bonding was successful. If the procedure fails, retry the bonding process. 11. Click Next when bonding is complete. Configure Local Port Settings The next step is to specify the local device’s port emulation settings and type. In this step, you will specify how the Wavespeed/S device communicates over the COM port to the device it is attached to.
SPP Server Configuration 1. Power the unit and connect it to a serial port on your computer. 2. Place both units in configuration mode by sliding the three-position switch to the far right, away from the power connector. 3. Launch the WvsdpCfg configuration utility. 4. In the first screen, select SPP Server in the Device Function box. Select COM Port 5. 6. Specify the COM port to which the local Wavespeed/S device is attached. The COM port can be selected in one of two ways. a.
9. When all settings are specified, click Set Port Configuration to send the settings to the local device. 10. After viewing the confirmation message, click Next. Configure Local Device 11. You may give the device a unique name. 12. Authentication: If authentication is enabled, the Wavespeed/S unit only connects to units that provide a matching PIN code as part of the authentication process. The PIN code is case sensitive and may be any combination of ASCII characters up to a maximum of 16. 13.
Specifications Power Input: 5V 3-Position Switch A 3-position switch (ON/OFF/CONFIG) determines the device’s current mode. ON is the normal operational mode for the device. CONFIG puts the device in configuration mode.
Pin Outs DTE Device: PIN DCE Device: Direction Signal PIN Direction Signal 1 Input DCD 1 Output DCD 2 Input RX 2 Output TX 3 Output TX 3 Input RX 4 Output DTR 4 Input DTR 5 -- GND 5 -- GND 6 Input DSR 6 Output DSR 7 Output RTS 7 Input RTS 8 Input CTS 8 Output CTS 9 Input RI 9 Output RI The fastest way to determine whether a device is a DTE or a DCE device is to check the voltage level on pin 2 of the DB-9 when the COM port is active.
Federal Communications Commission (FCC) Regulatory Information (USA only) 55001074 respectively). The following statement refers to this board. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
EN 55022 Class B (1994 w/A1 1995) EN61000-3-2 (2000) Test Requirement Test Limits for Specification Specification Requirement EN61000-3-2 EN55022 Radiated Emissions — Class B Conducted Emissions CISPR 22 Class B EN55024 (1998) Test Specification harmonic current emission — Class B EN61000-3-3 (1995) Requirement Test Specification EN61000-3-3 EN55024 Electrostatic Discharge EN61000-4-2 +4 kV contact +8kV air Radiated Immunity EN61000-4-3 3 V/m Electrical Fast Transient Burst EN61
