T r a n s P o r t ®W R 11 Wireless Routers EVDO Model HSPA+ Model LTE Model Installation Guide 90001936_B July 21, 2014
Digi TransPort® WR11 Installation Guide Copyright © 2014 Digi International Inc. All rights reserved. Digi, Digi International, the Digi logo, Digi TransPort®, and Digi TransPort WR11 are trademarks or registered trademarks in the United States and other countries worldwide. All other trademarks mentioned in this document are the property of their respective owners. Information in this document is subject to change without notice and does not represent a commitment on the part of Digi International.
Digi TransPort® WR11 Installation Guide Preface This guide describes the installation and configuration procedure for the Digi TransPort WR family of routers. It is intended to provide sufficient information to be able to connect the device to terminal equipment and power it on. A complete reference guide to the software features that are available on the product is available separately in PDF format and can be downloaded from the Digi International web site (www.digi.com).
Digi TransPort® WR11 Installation Guide Special Notes on Safety for Wireless Routers Digi International products are designed to the highest standards of safety and international standards compliance for the markets in which they are sold. However, cellular-based products contain radio devices which require specific consideration. Please take the time to read and understand the following guidance. Digi International assumes no liability for an end user’s failure to comply with these precautions.
Digi TransPort® WR11 Installation Guide Table of Contents Introduction to the Digi TransPort WR11 ������������������������������������������������������������������������������ 6 Digi TransPort WR11 EVDO Model Specifications ����������������������������������������������������������������������������� 6 Digi TransPort WR11 HSPA+ Model Specifications ��������������������������������������������������������������������������� 7 Digi TransPort WR11 LTE-MIMO Model Specifications �����������������������������
Digi TransPort® WR11 Installation Guide Introduction to the Digi TransPort WR11 Digi TransPort WR11 is a full-featured, cellular router offering the flexibility to scale from basic connectivity applications to enterprise class routing and security solutions. With its high performance architecture, Digi TransPort WR11 is designed for Wide Area Network connectivity including 2.5G, 3G and 4G networks.
Digi TransPort® WR11 Installation Guide Digi TransPort WR11 HSPA+ Model Specifications 8 D 11 WR P NS RA T IGI T OR 6 1 M2 1 al ce SIM SI r we Po 7 n Sig rvi Se 5 2 4 3 1. LAN: This Ethernet port connects the device to a 10/100 base-T Local Area Network (LAN). The port is capable of auto-sensing for speed and wiring, so it can accept both straight-through or cross-over cable connections. 2. Power Cord Input: This locking power connector connects the device to a power source.
Digi TransPort® WR11 Installation Guide Digi TransPort WR11 LTE-MIMO Model Specifications 8 AN WW PRI SP I DIG N TRA RT O 11 WR 9 AN WW SEC 6 1 E 2 VIC ER L NA 7 R WE PO SIG S 5 4 3 1. LAN: This Ethernet port connects the device to a 10/100 base-T Local Area Network (LAN). The port is capable of auto-sensing for speed and wiring, so it can accept both straight-through or cross-over cable connections. 2.
Digi TransPort® WR11 Installation Guide 8. Primary LTE Antenna Connector: This SMA female connector connects the device’s primary cellular antenna. 9. Secondary LTE Antenna Connector: This SMA female connector connects the device’s secondary cellular antenna.
Digi TransPort® WR11 Installation Guide Digi TransPort WR11 Configuration Once you have installed and powered up the device, you need to configure it to communicate with the LAN or WAN. You can configure the device either using the Command Line Interface (CLI) or the Web Interface. The recommended configuration option is the Web Interface, which you can access via a web browser such as Firefox, Internet Explorer or Chrome.
Digi TransPort® WR11 Installation Guide Digi TransPort WR11 Provisioning CDMA provisioning is different from GSM since CDMA (in most cases) does not use a SIM card. The CDMA module provisioning process creates a CDMA data connection to the mobile carrier network. This authenticates the modem and retrieves account information which is written to flash memory on the CDMA module itself, not the Digi’s configuration file. Mobile account information is stored on the CDMA module.
Digi TransPort® WR11 Installation Guide Verizon Provisioning For a Verizon device, press the Start button under CDMA Provisioning (Configuration - Networks > Interface > Mobile) leaving the fields blank as shown in the following image. Verizon LTE Configuration If using a Verizon LTE module (WR11-L800 or WR11-L900) and a standard Verizon LTE SIM, the device will connect by default.
Digi TransPort® WR11 Installation Guide Note: To maintain a reliable cellular connection, it is recommended that you enable Dead Link Detection on the mobile interface. The SureLink Wizard, located in the Wizard section of the WebUI, will walk you through the configuration. For additional information on this feature, refer to Application Note AN07 available at www. digi.com/support.
Digi TransPort® WR11 Installation Guide • All entered commands will take effect immediately. • All commands supported on the CLI are described in detail in the DigiTransPort User Guide available on the support site. Digi TransPort WR11 Communications Settings The default IP address of the device is 192.168.1.1 and it is configured to act as a DHCP server on the Ethernet interface. This means the WR11 will assign an IP address to a network device, such as a PC, connected to the Ethernet interface.
Digi TransPort® WR11 Installation Guide Troubleshooting the Digi TransPort WR11 Configuration This section provides information on resources and processes available for troubleshooting your Digi TransPort WR11 device. Troubleshooting Resources for Digi TransPort WR11 There are several resources available to you for support of your Digi product or resolving configuration difficulties at Digi’s Support site, http://www.digi.com/support/. Additional resources are as follows: 1.
Digi TransPort® WR11 Installation Guide 3. Right click on debug.txt and click Save target as. 4. Send the debug.txt file as an attachment. There are several ways to download the debug.txt file from Digi TransPort WR44RR device. For additional information on the other methods, view the online document QN24 - Extracting the debug.txt file from a Digi TransPort router.
Digi TransPort® WR11 Installation Guide For good performance, place the antenna 4.5 inches apart with an orientation of 30 degrees. For best results, place the antennas 8.5 inches apart with an orientation of 60 degrees. Inadequate antenna separation between the primary and secondary antennas creates unanticipated behaviors.
Digi TransPort® WR11 Installation Guide These include: • Reduced antenna efficiency, which limits: ◦◦ Transmit power ◦◦ Receiver sensitivity (RSSI) ◦◦ Data throughput Inadequate antenna separation can also have negative long-term effects on the cellular radio, reducing overall product lifespan.
Digi TransPort® WR11 Installation Guide Appendix A Digi TransPort WR11 Hardware Specifications Specifications Digi TransPort WR11 General Features: Dimensions (L x W x H) 3.9” x 5.2” x 1.3” Weight 0.85 lbs. (10 cm x 13.1 cm x 3.
Digi TransPort® WR11 Installation Guide Appendix B Digi TransPort WR11 Accessories The following sections provide the list of Digi TransPort WR11 accessories with the corresponding part numbers. Digi TransPort WR11 AC Power Supplies AC Power Supplies Part Number 5V 3.0A 2.5mm Locking, U.S. Plug 76000934 5V 3.0A 2.5mm Locking, International Plug Kit 76002021 Digi TransPort WR11 Cables Cables Part Number RJ45 to RJ45 crossover - 0.
Digi TransPort® WR11 Installation Guide Appendix C Digi TransPort WR11 Certifications Digi TransPort WR11 complies with the requirements of the following International Electromagnetic Compatibility (EMC) standards. International EMC (Electromagnetic Emissions/Immunity/Safety) Standards Digi TransPort WR11 complies with the requirements of the following Emissions, Immunity and Safety standards.
Digi TransPort® WR11 Installation Guide including interference that may cause undesired operation. If the FCC ID is not visible when installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module FCC ID. Modifications (FCC 15.21) Changes or modifications to this equipment not expressly approved by Digi may void the user’s authority to operate this equipment.
Digi International Inc.
