Digicom S.p.A. VoiceGATE Manual rev.2.0 VoiceGATE 8D5499 User’s Manual REV. 2.0 Pag.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Index IIDENT PREFACE ................................................................................................................ 3 1.0 GENERAL DESCRIPTION ........................................................................................ 4 1.1 LED Description.................................................................................................. 5 1.2 Connectors Description......................................................................
Digicom S.p.A. VoiceGATE Manual rev.2.0 PREFACE All rights reserved; no part of this publication may be reproduced, stored in a retrieval system, or trasmitted in any form or by any means, electronic, otherwise, without the prior written permission of Digicom S.p.A. The contents of this booklet may be modified without notice.
Digicom S.p.A. VoiceGATE Manual rev.2.0 1.0 GENERAL DESCRIPTION Digicom VoiceGATE is the ideal solution for the new Telecom Operators who want to take at home or office the new POTs with integration of Voice (Voice over IP) and Internet. VoiceGATE has 3 Ethernet ports (10/100) for the connection of local devices (Personal Computer, Printers, etc.), 2 analog ports and, optional, 1 SO ISDN bus with 2 RJ45 ports (for the connection ISDN telephones).
VoiceGATE Digicom S.p.A. Manual rev.2.0 1.1 LED Description The VoiceGATE status can be checked through seven led indicators. Lan x Line x Wan Pwr Indicates the LAN ports status Off: no device connected On: device connected Indicates the status of the two telephone lines Off: device not registered at the GateKeeper or internal address book not configured.
Digicom S.p.A. VoiceGATE Manual rev.2.0 2.0 Configuration VoiceGATE can be configured using a Web browser. (Explore, Netascape, etc). This chapter describes the test to carry out on the computer to enter the configuration and the procedure to save the mofications in the configuration. In the paragraph “VoiceGATE working test” you find the procedures to carry out your first tests with Digicom’s VoiceGATEs. Just few operations and you will be able to install and test two VoiceGATEs.
Digicom S.p.A. VoiceGATE Manual rev.2.0 2.2 Access to configuration 1. Run the browser and connect to http://192.168.2.1. When the connection is established, the following window will appear: Insert in the User Name field: admin Insert in the Password field: voicegate NB: User name and password must be written with lower case.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Note: in case of problems while displaying the configuration, be sure that no proxy Server is active. In Microsoft Internet Explorer the Proxy setup is in: Tools, Internet Options, Connections LAN, Settings. Menù Description 1. General Configuration It displays the information on the HW and SW release of the equipment. 2. Telephony Configuration It allows the reading and the voice parameters setup. 3.
VoiceGATE Digicom S.p.A. Manual rev.2.0 2.3 Save the configuration To confirm the new settings you must press the Submit button at the end of any WEB page. To activate the modifications it is necessary, before you exit the configuration, to enter the Save settings menu and press the Submit button. At this point VoiceGATE will execute a StartUP, then (after about 45 seconds) the modifications are active. Pag.
Digicom S.p.A. VoiceGATE Manual rev.2.0 2.4 VoiceGATE Working Test With simple operations you can test at once the working of VoiceGATE. We suggest to follow the procedures described in this chapter so to avoid working problems of VoiceGATE due to wrong configurations. The factory settings of VoiceGATE are the following: Voice: Ethernet: Mode: Address Book IP address: 192.168.2.1 Numbers: Line1->123 Line2 ->456 Subnet Mask: 255.255.255.
Digicom S.p.A. VoiceGATE Manual rev.2.0 2.5 Configuration Menù description General Information The information concerning the Hw and SW version and the elapsed time from the power on are displayed in this window. Pag.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Telephony Configuration The voice information are displayed in this window, in particular: Call Setting: defines the Voice working mode. It can be set to work with the Gatekeeper or with the internal address book. Codec Selected: it allows to define the priority list for the codec, when the codec is set in Automatic. “1” indicates the main codec. H323 Alias: name used when registering at the Gatekeeper. Note: This String must be different for each devices.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Interdigit Delay: wait in sec. from the last digit of the number, before starting the call. It is possible to activate the immediate dialling of the number, inserting the “#” character at the end of the number. Element in Gatekeeper: Gatekeeper IP address for registration. Maximum 4 addresses can be stored. Gatekeeper Keep Alive: Time in sec. for Gatekeeper registration renewal. Fixed Tei: TEI setup (Automatic or Fixed).
VoiceGATE Digicom S.p.A. Manual rev.2.0 Supplementary Services The information concerning the reading and the voice supplementary service setup, according the H.450 standard, are displayed in this window. You will find here a brief description of the various supplementary services. For almost all the supplementary services it is necessary to hold on a call (H.450.4 service enabled).
Digicom S.p.A. VoiceGATE Manual rev.2.0 H.450.4 Call Hold H.450.4 service allows to put on hold a call and to call another number. Once the two calls have been activated, you can: • • • Press R + 1 -> To close the active call and recover the on hold call. Press R + 2 -> To switch from a conversation to another, keeping one on hold. Press R + 3 -> To activate a three users conference.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Public Network Configuration The information concerning the reading and the Wan (Uplink) parameters setup are displayed in this window.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Private Network Configuration The information concerning the reading and the LAN part parameters are displayed in this window: <----- Attention: do not insert an IP address of the same network used in the WAN configuration “PublicNetwork Configuration”. If the WAN address is 192.168.2.1 you cannot use addresses 192.168.2.x.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Mac Addresses The Mac addresses of the device (Wan and LAN side) are displayed in this window. Public Network Mac: Mac address assigned to the WAN Private Network Mac: Mac Address assigned to the LAN SNMP Agent The information concerning the reading and the parameter setup of SNMP protocol are displayed in this window.
Digicom S.p.A. VoiceGATE Manual rev.2.0 RIP The information concerning the reading and the parameters setup of the RIP protocol are displayed in this window. RIP: Enables/Disables the RIP Silent Mode: OnlyRX – It manages the routing table in reception only RX+TX – It manages the routing table also in transmission Rip2 Mode: Multicast – It indicates if the RIP packets must be sent to the defined multicast address 224.0.0.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Route Table The informations concerning the routing table are displayed in this window. Security Configuration The informations concerning the password setup. Pag.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Save Setting In this page it is possible to save the modified configuration via browser, clicking on the Submit button. VoiceGATE will restart to load the new configuration. After about 45 seconds it will be ready to be used. Reset In this page it is possible to reset the device, clicking on the Submit button. VoiceGATE resets and load the current configuration. All the unsaved modifications are lost. Pag.
Digicom S.p.A. VoiceGATE Manual rev.2.0 3.0 VoiceGATE.exe The VoiceGATE utility allows to : - Create the “AddressBook” - Load the AddressBook in the VoiceGATEs - Upgrade the VoiceGATE firmware In the following parameters you will find some information on the use of the program; for further details refer to the Help on-line. 3.1 Address Book Management Address Book Management allows to create the address book in a simple way.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Gateway IP Address The IP Address field concerning the Gateway represents the IP Address of an eventual PSTN/ISDN Gateway. The Gateway allows the communication between the VoIP network and the traditional telephone lines (PSTN, ISDN and GSM). If the VoiceGATE doesn’t find the selected number in the address book, it sends it to the Gateway, that will call the selected number.
Digicom S.p.A. VoiceGATE Manual rev.2.0 3.2 Address Book Upgrade Through the Address Book Upgrade you can send the address book created with the Address Book Management. After selecting Address Book Upgrade choose the address book file to be sent. Insert the IP address, UserID and Password of the VoiceGATE to which you must send the address book, then confirm with ADD. If you want to send the address book to other VoiceGATEs it is sufficient to repeat the procedure, adding more addresses in th list.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Configuration Example Here is an example to use the VoiceGate and its configuration. In teh following application there are two VoiceGATE (one in the main office and the other one in the branch office) and no Gatekeeper is required. We will use the internal address book to configurate the VoiceGate. To set the device it is necessary to know the information concerning the company network where you want to install the VoiceGate.
Digicom S.p.A. VoiceGATE Manual rev.2.0 In this menu insert the following information:: - Alias - The two telephone numbers - If you yse the internal address book or the reference Gatekeeper. In this example we choose the Address book mode, setting the Call Setting parameter as Address Book. In the Public Network Configuration Menu you define the information concerning the VoiceGate WAN interface. Insert the IP Address and the Subnet Mask.
Digicom S.p.A. VoiceGATE Manual rev.2.0 In the Private Network Configuration menu you define the information concerning the VoiceGate LAN interface. Besides the IP address and the SubnetMask, you have to enable the NAT. Configuration example of the PC Ethernet card to connect to the VoiceGate LAN ports. You have to insert the DNS regarding your ADSL account. NOTE: To set the VoiceGate internal address book, refer to the chapter: VoiceGate.exe Pag.
VoiceGATE Digicom S.p.A. Manual rev.2.0 VoiceGATE Configuration Work Sheet Installation: Company: Office: Installed By: Date: Hardware Information: Firmware Information: Code: Sw Version: Serial Number: Build: Isdn Version: Telephony Configuration: H323 Alias: Call Setting GateKeeper: AddressBook: Phone Number Line 1 Number Codec Line 2 Number Codec Line 3 Number Codec Line 4 Number Codec GK- IP Address: Codec Selected Priority List G.711-A G.711-u G.729 G.729-A G.729-B G.
Digicom S.p.A. VoiceGATE Manual rev.2.0 Pag.
