規 格 承 認 書 SPECIFICATION FOR APPROVAL 客 戶(CUSTOMER)：太業科技股份有限公司 貴公司承認 CUSTOMER APPROVE 品 名(DESCRIPTION)：DC FAN 規 格 料 號 備 註 L:300±5mm MF17080V2-10000-G99 +MOLEX 22-01-3037 (黑紅黃) (DC5V 17*17*8mm 三線 F Type) (或 EQUIVALENT) 產 地(ORIGINAL)： 建準電機工業股份有限公司(Sunonwealth Electric Machine Industry Co., Ltd.) 806 高雄市前鎮區新衙路 296 巷 30 號 No.30, Lane 296, Sinya Rd., Cianjhen District, Kaohsiung City 806, Taiwan TEL：07-8156100 FAX：07-8231010 佛山市建準電子有限公司(Sunon Electronics (FoShan) Co., Ltd.
SUNON SPECIFICATION FOR APPROVAL CUSTOMER : 承毅科技股份有限公司 MOTOR TYPE : DESCRIPTION : MagLev Motor Fan DIMENSIONS : 17X17X8 mm MODEL : MF17080V2-10000-G99 SUNON SPEC. NO. : D01003230G-00 CUSTOMER APPROVAL NO. APPROVED BY CUSTOMER : : (AUTHORIZED) DRAWN Vickey 5/23 CHECKED YAN APPROVED Sunny SPEC.NO D01003230G-00 ISSUE DATE 05.23.2017 EDITION 0 REVISION DATE E.SPEC E11600436 建準電機工業股份有限公司 SUNONWEALTH ELECTRIC MACHINE INDUSTRY CO., LTD. TEL:886-7-8135888 NO. 30, LN. 296, XINYA RD.
I.
II. SPECIFICATION 1. MECHANICAL CHARACTERISTIC MOTOR DESIGN Single phase, 4-poles Brushless DC motor BEARING SYSTEM Vapo bearing system DIMENSIONS See Page 6 MATERIALS OF FRAME Thermoplastic PBT of UL 94V-0 MATERIALS OF FAN BLADE Thermoplastic PBT of UL 94V-0 DIRECTION OF ROTATION Counter-clockwise viewed from front of fan blade MOUNTING HOLES Diameter 2 mm in 3 holes WEIGHT 3.9 g 2. ELECTRIC CHARACTERISTIC RATED VOLTAGE 5 VDC RATED CURRENT 66 mA / Max. 76mA RATED POWER CONSUMPTION 0.
3. PERFORMANCE CHARACTERISTIC RATED SPEED 16500 RPM ± 15% at rated voltage AIR FLOW 0.7 CFM STATIC PRESSURE 0.17 Inch-H2O ACOUSTIC NOISE 14.2 dB(A) @ 1M 34.2 dB(A) @ 0.1M AIR FLOW V.S. PRESSURE See Page 5 INSULATION CLASS UL Class A INSULATION RESISTANCE 10M ohm at 500 VDC between internal stator and Lead wire (+) PLASTIC HOUSING DIELECTRIC STRENGTH Applied AC 500 V for one minute or AC 600 V for 2 Seconds between housing and lead wire (+) LIFE EXPECTANCY 60,000 Hours at 40 deg.
MODEL : MF17080V2-10000-G99 Static Pressure (Inch-H2O) 0 0.0056 0.0112 CURVES 0.0168 0.2 0.0224 5 0.16 4 0.12 3 0.08 2 0.04 1 m3/min mm-H2O PERFORMANCE 0 0 0 0.2 0.4 0.6 0.8 Air Flow-CFM 建 準 電 機 SUNONWEALTH Page 5 of 15 D.C.C. 2017.05.
DIMENSIONS Screw Type (Pan head) Torque Machine screw 1～2 Kgf-cm Screw Spec Size Standard M1.7 JIS B1111-1974 Note: SUNON recommends the screw and torque as above. Please contact SUNON, if any new requirement is requested. UNIT：mm 建 準 電 機 SUNONWEALTH Page 6 of 15 D.C.C. 2017.05.
LABEL 建 準 電 機 SUNONWEALTH Page 7 of 15 D.C.C. 2017.05.
FAN 3rd WIRE SIGNAL ● F Type (Frequency Generator) 建 準 電 機 SUNONWEALTH Page 8 of 15 D.C.C. 2017.05.
III. OTHER SPECIFIED TESTING The following is a general description of certain tests that are performed on representative SUNON fans. Nothing in this document is intended to suggest that these tests are performed on every model of SUNON fan. Moreover, the descriptions that follow each test are meant only to provide a general explanation of each test. If you would like a more detailed explanation as to any test identified in this Section, SUNON can provide such an explanation upon request. 1.
IV. CHARACTERISTIC DEFINITION The following is a general description of certain tests that are performed on representative SUNON fans in order to determine the specifications of the fan. Nothing in this document is intended to suggest that these tests are performed on every model of SUNON fan. Moreover, the descriptions that follow each test are meant only to provide a general explanation of each test.
4. RATED SPEED Measured after continuous 10 minute operation at rated voltage in clean air ( STATIC PRESSURE=0), and at ambient temperature of 25 degrees C under shaft horizontal condition. 5. STARTING VOLTAGE Measured the voltage which enables to start the fan in the clean air (static pressure = 0 ) by switching on at the voltage under shaft horizontal condition. It is not at continuously increasing voltage adjustment. 6. LOCKED ROTOR CURRENT Measured immediately after the fan blade is locked. 7.
V. NOTE Ⅰ.SAFETY 1. DO NOT use or operate this fan in excess of the limitations set forth in this specification. SUNON is not responsible for the non-performance of this fan and/or any damages resulting from its use, if it is not used or operated in accordance with the specifications. 2. SUNON recommends adding a protection circuit to the product or application in which this fan is installed, such as a thermo-fuse, or current-fuse or thermo-protector.
II. SPECIFICATION MODIFICATION 1. SUNON offers engineering assistance on fan installation and cooling system design. 2. All changes, modifications and/or revisions to the specifications, if any, are incorporated in the attached specifications. 3. No changes, modifications and/or revisions to these specifications are effective absent agreement, by both SUNON and the customer, in writing. 4.
6. Fan guards may prevent injury during handling or installation of the fan and are available for sale with this fan. 7. Unless otherwise noted, all testing of this fan is conducted at 25°C ambient temperature and sixty-five percent (65%) relative humidity. 8. DO NOT store this fan in an environment with high humidity. This fan must be stored in accordance with the attached specifications regarding storage temperature.
Declaration of RoHS Control declaration of environment-related substances/materials 1. In accordance with the Restriction of Hazardous Substances (RoHS) Directive 2011/65/EU, SUNON product have complied with law and discipline not to employ the forbidden substances, and restrict the allowable concentration of some limited substances deliberately in our components.
