Datasheet

Zynq-7000 All Programmable SoC (Z-7007S, Z-7012S, Z-7014S, Z-7010, Z-7015, and Z-7020)
DS187 (v1.19) October 3, 2016 www.xilinx.com
Product Specification 2
V
IN
(3)(4)(5)
I/O input voltage for HR I/O banks –0.40 V
CCO
+0.55 V
I/O input voltage (when V
CCO
=3.3V) for V
REF
and differential I/O standards
except TMDS_33
(6)
–0.40 2.625 V
V
CCBATT
Key memory battery backup supply –0.5 2.0 V
GTP Transceiver (XC7Z015 Only)
V
MGTAVCC
Analog supply voltage for the GTP transmitter and receiver circuits –0.5 1.1 V
V
MGTAVTT
Analog supply voltage for the GTP transmitter and receiver termination
circuits
–0.5 1.32 V
V
MGTREFCLK
Reference clock absolute input voltage –0.5 1.32 V
V
IN
Receiver (RXP/RXN) and Transmitter (TXP/TXN) absolute input voltage –0.5 1.26 V
I
DCIN-FLOAT
DC input current for receiver input pins DC coupled RX termination = floating – 14 mA
I
DCIN-MGTAVTT
DC input current for receiver input pins DC coupled RX
termination = V
MGTAVTT
–12mA
I
DCIN-GND
DC input current for receiver input pins DC coupled RX termination = GND – 6.5 mA
I
DCOUT-FLOAT
DC output current for transmitter pins DC coupled RX termination = floating – 14 mA
I
DCOUT-MGTAVTT
DC output current for transmitter pins DC coupled RX
termination = V
MGTAVTT
–12mA
XADC
V
CCADC
XADC supply relative to GNDADC –0.5 2.0 V
V
REFP
XADC reference input relative to GNDADC –0.5 2.0 V
Temperature
T
STG
Storage temperature (ambient) –65 150 °C
T
SOL
Maximum soldering temperature for Pb/Sn component bodies
(7)
– +220 °C
Maximum soldering temperature for Pb-free component bodies
(7)
– +260 °C
T
j
Maximum junction temperature
(7)
– +125 °C
Notes:
1. Stresses beyond those listed under Absolute Maximum Ratings might cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those listed under Operating Conditions is not implied.
Exposure to Absolute Maximum Ratings conditions for extended periods of time might affect device reliability.
2. Applies to both MIO supply banks V
CCO_MIO0
and V
CCO_MIO1
.
3. The lower absolute voltage specification always applies.
4. For I/O operation, refer to the 7 Series FPGAs SelectIO Resources User Guide (UG471
) or the Zynq-7000 All Programmable SoC Technical
Reference Manual (UG585
).
5. The maximum limit applies to DC signals. For maximum undershoot and overshoot AC specifications, see Table 4.
6. See Table 11 for TMDS_33 specifications.
7. For soldering guidelines and thermal considerations, see the Zynq-7000 All Programmable SoC Packaging and Pinout Specification
(UG865
).
Table 2: Recommended Operating Conditions
(1)(2)
Symbol Description Min Typ Max Units
PS
V
CCPINT
PS internal logic supply voltage 0.95 1.00 1.05 V
V
CCPAUX
PS auxiliary supply voltage 1.71 1.80 1.89 V
V
CCPLL
PS PLL supply 1.71 1.80 1.89 V
V
CCO_DDR
PS DDR I/O supply voltage 1.14 – 1.89 V
V
CCO_MIO
(3)
PS MIO I/O supply voltage for MIO banks 1.71 – 3.465 V
Table 1: Absolute Maximum Ratings
(1)
(Cont’d)
Symbol Description Min Max Units