Datasheet

Zynq-7000 All Programmable SoC (Z-7007S, Z-7012S, Z-7014S, Z-7010, Z-7015, and Z-7020)
DS187 (v1.19) October 3, 2016 www.xilinx.com
Product Specification 65
Table 93: GTP Transceiver Receiver Switching Characteristics
Symbol Description Min Typ Max Units
F
GTPRX
Serial data rate RX oversampler not enabled 0.500 – F
GTPMAX
Gb/s
T
RXELECIDLE
Time for RXELECIDLE to respond to loss or restoration of data – 10 – ns
RX
OOBVDPP
OOB detect threshold peak-to-peak 60 – 150 mV
RX
SST
Receiver spread-spectrum
tracking
(1)
Modulated @ 33 KHz
–5000 – 5000 ppm
RX
RL
Run length (CID) – – 512 UI
RX
PPMTOL
Data/REFCLK PPM offset tolerance –1250 – 1250 ppm
SJ Jitter Tolerance
(2)
JT_SJ
6.25
Sinusoidal Jitter
(3)
6.25 Gb/s 0.44 – – UI
JT_SJ
5.0
Sinusoidal Jitter
(3)
5.0 Gb/s 0.44 – – UI
JT_SJ
4.25
Sinusoidal Jitter
(3)
4.25 Gb/s 0.44 – – UI
JT_SJ
3.75
Sinusoidal Jitter
(3)
3.75 Gb/s 0.44 – – UI
JT_SJ
3.2
Sinusoidal Jitter
(3)
3.2 Gb/s
(4)
0.45 – – UI
JT_SJ
3.2L
Sinusoidal Jitter
(3)
3.2 Gb/s
(5)
0.45 – – UI
JT_SJ
2.5
Sinusoidal Jitter
(3)
2.5 Gb/s
(6)
0.5 – – UI
JT_SJ
1.25
Sinusoidal Jitter
(3)
1.25 Gb/s
(7)
0.5 – – UI
JT_SJ
500
Sinusoidal Jitter
(3)
500 Mb/s 0.4 – – UI
SJ Jitter Tolerance with Stressed Eye
(2)
JT_TJSE
3.2
Total Jitter with Stressed Eye
(8)
3.2 Gb/s 0.70 – – UI
JT_TJSE
6.25
6.25 Gb/s 0.70 – – UI
JT_SJSE
3.2
Sinusoidal Jitter with Stressed
Eye
(8)
3.2 Gb/s 0.1 – – UI
JT_SJSE
6.25
6.25 Gb/s 0.1 – – UI
Notes:
1. Using RXOUT_DIV = 1, 2, and 4.
2. All jitter values are based on a bit error ratio of 1e
–12
.
3. The frequency of the injected sinusoidal jitter is 10 MHz.
4. PLL frequency at 3.2 GHz and RXOUT_DIV = 2.
5. PLL frequency at 1.6 GHz and RXOUT_DIV = 1.
6. PLL frequency at 2.5 GHz and RXOUT_DIV = 2.
7. PLL frequency at 2.5 GHz and RXOUT_DIV = 4.
8. Composite jitter.