Digimax 210 Programmable Thermostat Compatible with Maxi Controller User Guide
Schema of the thermostat RF DigiMax 210 Ambient temperature Set Key Up Key Down Key The RF DigiMax 210 thermostat does not need any extra wiring and works within 30 meters range. It is equiped of a secured RF code which the Maxi Controller will learn during the installation process (see §8b). This code will assure that the Maxi Controller will only answer to messages sent by your DigiMax 210. This process is described at the end of this manual.
To change the “Set Point” (i.e. temperature requested), press and hold the “SET” key and at the same time press “+” or “-” to select the temperature setting. The display will show the “Set Point” until the “SET” button is released. The display will then show the ambient temperature. When the DigiMax 210 instructs your heating system to switch on, a small flame symbol appears at the bottom right of the display.
) Position The ideal position to locate the DigiMax 210 is about 1.5m above floor level, accessible, free from extremes of temperature and draught. Do not mount it on an outside wall, above a radiator or where it may be subjected to direct sunlight. The radio link does not mean that the wiring has been simplified, but that the thermostat can be installed in any place of your house to optimate your needs in heating.
2. Locate and identify the two option Links 1 and 2. Use a pair of small wire cutters to cut the appropriate links to give the required configuration. 3. Cutting Link 1 will give a minimum temperature set point of 16°C (factory default is 5°C) : in that case, the minimum T° you can set is 16°C. Cut link 2 to display cooling symbol instead of heating symbol. 4. Replace batteries being sure to observe the correct polarities. Re-fit to plastic base and tighten retaining screw.
7) Battery replacement A “flashing” battery low symbol will appear at the bottom left of the display when the batteries start to approach the end of their life. This indicates that they should be replaced within the next month. Ultimately, the display will start flashing and the thermostat will shut down until the batteries are replaced. To replace the batteries, the following procedure should be carried out. 1. Slacken the retaining screw on the unit and open by hinging upwards the top edge. 2.
8) Connection to the the Maxi Controller a) General operation You can connect up to 4 DigiMax 210 to the Maxi Controller. Depending on the information sent by the thermostats, the Maxi Controller will send X10 messages on the power line to turn On or Off X10 modules connected to your heaters or boiler. These X10 modules can be Din appliance modules (AD10) for boilers working on 230V or Universal modules (UM7206) for boilers working on low voltage (up to 24V).
b) Installation Setthe security console mode switch to the THERM position. 2.To installa thermostatwith the console,press and hold its + and - keys together for 3 seconds. The DigiMax 210 1. 3. 4. 5. 6. will then transmit its unique digital code every 10 seconds for the next 5 minutes. The display will show flash ‘]]]’ while this is happening.
- thermostat on zone 2 will generate message on code B2, - thermostat on zone 3 will generate message on code B3, - thermostat on zone 4 will generate message on code B4. If the console is on Housecode B, - thermostat on zone 1 will generate message on code C1, thermostat on zone 2 message on code C2 etc... c) programming of the setback temperature 1. Set the security console mode switch to the INSTALL position. 2. Key in your PIN code (factory default 0000). 3. Press key number 9 4. Press ENTER 5.
5. Dial via the phone “99#”, you will hear 3 short confirmation beeps. 6. The setback differential is now applied to the comfort setpoint. Apply the comfort setting 1. Call the security console from a touch tone or mobile phone. 2. The security console will answer your call with 3 short beeps. 3. After these beeps, enter your PIN code via the phone (factory default 0000). 4. The console confirms a correct PIN code with 3 beeps (an erratic PIN code is indicated by one long beep). 5.
f) Trouble shooting : 1. Comfort temperature If you do not manage to set a temperature level under 16 ° C, check that the thermostat has not been set in order to avoid a lower temperature level. Refer to the chapter 6 “configuring” of this user guide. 2. Operating troubles If the boiler does not work on the request of the security console, check the battery symbol on the DigiMax LCD. Change the batteries if necessary.
