INSTRUCTION MANUAL Ultra Resolution Day & Night Bullet Camera Ultra Resolution Day & Night Bullet Camera P/N 01.BSM.11.0070201B V1.0 Models: DPB14TLX Please read this manual thoroughly before use and keep it handy for future reference.
INTRODUCTION Features • 1/3” Sony Super HAD™ II CCD • Excellent low light performance using Polaris Vision 2 technology. • Smart IR technology • 0.15 Lux / F1.2 (Color) 0.001 Lux w/Sense-Up at x256 0 Lux w/IR LED • 600 TV lines(Color) of resolution • • • • • • • • 3D Digital Noise Reduction (3D-DNR) OSD menu control True Day/Night with ICR Privacy Masking / Motion Detection VIDEO OUT(BNC) Test Monitor Output 2.8-10.5mm Varifocal Day/Night Lens F1.
MEASUREMENTS INSTALLATION 1 100.9 mm 4.0" 1a) Loosen the thread nut with the included allen key and turn the camera base counter clockwise to remove it from the camera mount. 101.5 mm 4.0" CDS 1b) Mount the camera base to the surface. NOTE: The camera base is compatible with an Octagon junction box 88.0 mm 3.5" 298.6 mm 11.8" 2 PACKAGING CONTENT 2a) Attach camera back onto the camera base by turning it counter clockwise. 2b) Tighten the thread nut to secure the camera’s horizontal angle.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT Menu Setup LENS Using this function, you can control screen brightness. 1. Highlight 'LENS' in the main setup menu 2. Press the ENTER to access the DC lens setup menu. 3. After completing setting update, highlight 'RETURN' to save setting and return to previous menu Service Connector output. Use supplied cable to connect to this output. OSD function controls. Pressing down on middle button acts as ENTER function.
CAMERA ADJUSTMENT SENSE-UP CAMERA ADJUSTMENT BACKLIGHT (BLC) EXPOSURE SHUTTER BRIGHTNESS AGC SENSE-UP BLC D-WDR RETURN The BLC menu is used to adjust backlight compensation function to sharpen subjects in backlight situations AUTO ----|---- 50 MIDDLE AUTO BLC OFF RET Select digital slow shutter speed setting in order to allow extra light into the camera thereby providing higher sensitivity in low light conditions.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT Wide Dynamic Range (D-WDR) SETUP 1. LENS 2. EXPOSURE 3. WHITE BAL 4. 3DNR D-WDR : The D-WDR menu is used to adjust dynamic range of the camera electronically. This is especially useful in high contrast scenes in order to brighten up darker parts of the scene. 1. Highlight 'D-WDR' in the exposure setup menu. 2. Move buttons left and right to change setting to OFF/INDOOR/OUTDOOR.
CAMERA ADJUSTMENT Digital Noise Reduction (3D DNR) This function reduces the background noise in a low luminance environment. 1.Highlight '3DNR' in the main setup menu. SETUP 1. LENS 2. EXPOSURE 3. WHITE BAL 4. 3DNR MANUAL AWB ON 2. Press the left/right buttons to change setting to OFF/ON OFF - Noise is not reduced ON - Noise is reduced 3. Press ENTER to access the submenu for ON setting. In the 3DNR submenu you can adjust the noise reduction level values range from 0 to 100. Default setting is 60.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT D-EFFECT: Applies digital effects to camera image. 1. Highlight 'D-EFFECT' in the SPECIAL setup menu. Notes • When the CAM TITLE is OFF no title will be displayed on the monitor even if you had previously setup a name. This is the master display setting. • Only English is available in this mode for camera title. • Only max 15 characters for the title allowed. 2. Press ENTER to access the submenu for ON setting. Here you will be able to enter the camera title.
CAMERA ADJUSTMENT CAMERA ADJUSTMENT MOTION: You can monitor activity more efficiently, because a signal is generated by the camera whenever motion is detected. Visual notification is also available. 1. Highlight 'MOTION' in the SPECIAL setup menu SPECIAL OFF RET POSITION MOTION - AREA SELECT: - AREA DISPLAY: - SENSITIVITY: - MOTION VIEW: Select motion detection area number. AREA 1-4 With the area slected will be shown flashing on and off visually.
TROUBLESHOOTING Refer to the following table if you are experiencing trouble with your camera. Contact an authorized technician if the table does not provide you with a solution to the trouble. Nothing appears on the screen. Check that the power cord and line connection between the camera and monitor are connected properly. Check that you have properly connected VIDEO cable to the camera VIDEO output jack. The image on the screen is dim. Is lens stained with dirt? Clean lens with soft, clean cloth.