TM MIX-16 CENTRAL MIXER USER GUIDE 1266 Park Road Chanhassen, MN 55317 952-401-7700 support@digitalaudio.com www.digitalaudio.com Version 1.
SAFETY INSTRUCTIONS TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. NO USER SERVICEABLE PARTS INSIDE. CONTACT DIGITAL AUDIO LABS FOR SERVICING. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of un-insulated and/or potentially dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
CONTENTS Safety Instructions................................................................................................. ii Important Safety Instructions.................................................................... ii Care.......................................................................................................... ii Digital Audio Labs Limited Warranty..................................................................... 1 Repair Policy................................................
DIGITAL AUDIO LABS LIMITED WARRANTY Digital Audio Labs warrants their products against defects in material and workmanship for a period of two years from date of purchase. During this period, Digital Audio Labs will, at its option, repair the defective unit or replace it with a new or rebuilt one. The warranty does NOT cover: • Damage due to abuse, misuse, or accident. • Damage due to operation contrary to the instructions in the product instruction manual.
CONTENTS OF BOX • MIX-16 • External Power Supply INTRODUCTION The MIX-16 is the Central Mixer of the Livemix system. Although the Control Surfaces are where most of the mixing is controlled, the actual mixing happens in the MIX-16.
4. Control Surface Ports: Each port supplies both power and audio to connected Control Surfaces through a standard CAT5 cable. Two indicator lights on each port report device status information. • The green light will illuminate when a CS-DUO has a valid connection with the MIX-16. • The yellow light is a fault indicator. It may illuminate briefly when each control surface is powered on. If it remains lit, this indicates a problem with the port, the CAT5 cable or the CS-DUO.
DB25 CABLE (TASCAM PINOUT) TRS CABLE SETUP DIAGRAMS LIVEMIX DATA AD-24 LIVEMIX DATA OUT Analog Input to MIX-16 AD-24 LIVEMIX DATA OUT LIVEMIX DATA AD-24 12VDC 3.33A 12VDC 3.33A SHIELDED CAT5 LIVEMIX DATA OUT MIX-16 LIVEMIX DATA OUT STEREO MIXES 17-32 (MIX-32 ONLY) LIVEMIX DATA IN STEREO MIXES 1-16 AD-24 LIVEMIX DATA OUT 24VDC 3.75A 12VDC 3.
LIVEMIX DATA OUT MIX-16 MIX-16 to CS-DUO Control Surfaces 1 2 3 4 5 6 LINK/ACT 7 LM-DANTE-EXP DANTE NETWORK STEREO MIXES 17-32 (MIX-32 ONLY) 1G LIVEMIX DATA IN LIVEMIX DATA OUT STEREO MIXES 1-16 24VDC 3.75A Dante™ is a trademark of Audinate Pty Ltd.
SETUP AND OPERATION Although the MIX-16 is the Central Mixer of the Livemix system, there are no direct controls. Setting up the MIX-16 is simple and all configuration is done through an attached Control Surface (covered in the CS-DUO manual). 1. If using the analog input, connect the Livemix Data Out port on the AD-24 to the Livemix Data In port on the MIX-16. Please use shielded CAT5 or CAT6 cable to make this connection. If using an option card, you will not use the Livemix Data In port. 2.
LIVEMIX SYSTEM OVERVIEW There are three components required to make a Livemix system. Each system will have either an analog or digital input unit, a central mixer unit, and at least one attached control surface. Input Options Users with analog source material will use the AD-24. Using the TRS or DB-25 inputs, audio from the source material is made available to the Livemix system. Users with digital source material will use the Dante Option Card (LM-DANTE-EXP).
TROUBLESHOOTING My MIX-16 is not powering on correctly. • Verify that you have connected the external power supply to a working power outlet • Verify that the front panel power switch is set to ON. I am not seeing the “Livemix Data” light illuminate. If the Livemix Data light is not illuminating, there is a problem with the power to the MIX-16. Check to make sure that the power supply is connected to the MIX-16 and that all the cables are secure.
LIVEMIX SUPPORT Phone Support: Toll Free: Email Support: Website: 952-401-7700 844-DAL-INFO support@digitalaudio.com www.digitalaudio.
Open Source Statement The Livemix MIX-16 firmware includes the open source software module FreeRTOS, which is licensed under the terms of the GNU General Public License (version 2) AND MODIFIED BY the FreeRTOS exception, as outlined in the FreeRTOS license. In accordance with those licensing terms, we must provide you the source code for the version of FreeRTOS used in the MIX-16. You may download the FreeRTOS source code at http://www.digitalaudio.com/open-source-center.