20” WIDE TFT-LCD TV Owner s Manual
Thank you for buying our 20” LCD TV. Please take the time to read this manual for the best performance of this TV. Please keep this manual for future reference. The present home appliance is certified and approved by EMC/EMI and can be used in all places including residency area. Information in this manual is subject to change without prior notice. ! Safety Instructions Ver 1.
Warning Warning Disconnect the power cable and signal cable connected to the product in case of thunder or lightning. Do not arrange the power cord close to any heating devices/sources. Do not attempt to touch its power cord with wet hands. If any electric pin is wet or dusty, remove the moisture or dust first before use. Install the outdoor antenna for the set far away from high voltage cables. It is recommended to pull out the power cord unless you use it for a long time.
Contents Available Temperature & Humidity Operating Temperature 0~40˚C Storage Temperature -10~50˚C Operating Humidity 10~60% RH Storage Humidity 10~90% RH CHAPTER 1. Before Use 1-1. Accessories 10 1-2. Panels 11 1-3. Remote Control 14 1-4. Menu Configuration 16 However the pixels of R.G.B. & White color seem to be right sometimes or some of 1-5. Jog Shuttle Button 18 black pixels could be seen on the LCD. This is not from bad quality or functional 1-6.
1 Before use CHAPTER 4. Using Menus of Picture, Sound and Others 1-1. Accessories 4-1. Setting Picture Mode 36 4-2. Setting Sound Mode 39 4-3. Setting Option 40 CHAPTER 5. 1-2. Panels 1-3. Remote Control 1-4. Menu Configuration Using PC MENU 1-5. Jog Shuttle Button 5-1. Auto Adjustment 42 5-2. Setting Picture 43 5-3. Setting PC Scale Mode 44 5-4. Setting Sound 45 5-5. Setting Option 46 5-6. Setting Color Temperature 47 CHAPTER 6. Specifications 6-1. Dimensions 50 6-2.
1-1 Accessories 1-2 Panels Please make sure the following items are included with your LCD TV. If any items are missing, contact your dealer. AAA-type battery( 2) 1) Front Panels RF Cable - Power Cord - DC Adaptor - - - Power / Menu Channel Button Sound Cont.
2) Rear Panels 3) Side Panels COMPONENT (HDTV) Video Input (Pb Y Pr) COMPONENT (HDTV) Audio Input (L R) Power Input Vodeo Input PC Input S-Vodeo Input COMPONENT (DVD) Video Input AV Input (L R) COMPONENT (DVD) Audio Input Upgrade Input Audio (PC input / Headphone Output) TV Antenna Input 12 20 WIDE TFT-LCD TV 13
1-3 Remote Control Functions by remote control buttons Button Function Button Function POWER Power On/Off MUTE Sound off Temporarily 0~9 Numeric Buttons.
1-4 MENU Configuration Most functions of the TV set can be controlled by MENU and selection buttons on the 2) Using Remote Control remote control, so learning how to operate them would be convenient for you. Press MENU button to display main menu. 1) Menu Configuration Press Menu control button ( / ) to move to sub menu of a Main Menu Sub Menu Settings selected main menu. To move among menus, use Menu control button ( / ). To change a selected menu setting, use Menu control button ( / ).
1-5 JOG Shuttle Button Push MENU button right to display main menu. Push it right again to display sub menu. Push MENU button left to return to main menu. Push it left again to clear menu. 2 Connection 2-1. Connecting Power 2-2. Connecting TV Antenna Push the button up and down to move among menus. If pushing it upward when menu is not displayed, it controls automatic PC settings. 2-3. Connecting PC 2-4. Connecting DVD If pushing it downward when menu is not display, it changes input signals.
2-1 Connecting Power 2-3 Connecting PC The product automatically adjusts voltage. Power Cable should be firmly connected to an outlet or DC adaptor in order not to be pulled out or shake. 2-2 Connecting TV Antenna When round cable (75Ω coaxial cable) is used, copper part of the cable should not be bent. Connect D-Sub Cable to D-Sub port on the TV and PC. Connect Audio Cable (not included) to Audio output of a PC (stereo jack) and PC Audio Input Port of the TV (stereo jack).
2-5 Connecting HDTV Audio signals of S-VIDEO should be used with external audio signal cables. S-VIDEO signal secures better picture quality than composite video signal. Digital TV Broadcasting Receiver Connect Component Cable (not included) to HDTV Connection ports of TV (Pb Y Pr) and DTV Receiver. Connect Audio Cable (not included) to Audio ports (L/R) of TV and DTV Receiver. Cables should be connected to ports of the same colors.
3 Using TV Menus 3-1. Watching TV 3-2. Channel Search & Fine Tune 3-3. Add/Remove Channel 3-4. Channel Swap 3-5. Change TV Channel Mode 3-6. Closed Caption 3-7.
Watching TV 3-1 5) Volume Control 1) Precautions in the initial installation Increase/decrease volume by pressing Press VOL button ( + / - ) on the remote control. VOL button ( + / - ) on the TV set to control the volume. Check whether TV antenna cable is properly connected. After checking whether the voltage is 100V or 220V, supply the electric power and connect the adaptor to the TV. At the moment, TV is in standby.
8) Selecting the Sound Mode You can select a sound setting among ,, or . 9) Setting Multi-Channel Sound (MTS) Depending on the particular program being broadcast, you can listen to stereo, mono, or a Secondary Audio Program. (SAP audio is usually a foreign-language translation. Sometimes SAP has unrelated information like news or weather.) Press the MTS button. Each press of the MTS button cycles through , and .
3-3 Add/Remove Channel You may add or remove a channel as your need. - Move to a channel to add or remove by pressing numeric buttons(0~9) or CH - Press button. MEM button on the remote control. - In case of adding a channel by using button on the remote control, move to Add. - Also, it can be set in OSD menu if JOG button is used. 3-4 Channel Swap 3-5 Change TV Channel Mode Please choose your TV input type by selecting either Air or Cable.
3-7 V-Chip Function This function deals with MPAA rating of TV broadcast and other media. It works only with V-Chip function broadcast and media. - Press MENU button on the remote control and move to menu. - Set the V-Chip menu by using button on the remote control. 3-6 Closed Caption This function works only with caption broadcast or other CC marked video tape and DVD title. Default V-Chip PIN is 0000. Set the function in the SETUP menu. Please change PIN as yours when you install.
- Move to TV Guideline or MPAA Rating by using CH button on the remote control. 4 Using Menus of Picture, Sound and Others - Move to the position which you want to make channel blocking and press MENU button for setting. - Press it again for cancellation. 4-1. Setting Picture Mode 4-2. Setting Sound Mode 4-3. Setting Option - Escape the menu pressing EXIT. - V-chip function can be set up only by the remote control.
4-1 Setting Picture Mode 2) Mode : Standard - Soft - Dynamic - User By setting a picture mode suitable for broadcasting/video signals, you may enjoy better By setting a picture mode suitable for broadcasting/video signals, you may enjoy better quality picture. quality picture. 1) Image Scale : Full - 4:3 You can set the screen’s suitable image scale of TV or Video input signals and view - Press PM button on the remote control. Standard : Standard picture mode.
4) Contrast : Adjust screen contrast 5) Color : Adjust screen color 4-2 Setting Sound Mode You can set sound suitable for TV broadcasting or Video. 1) Mode Setting 6) Tint : Adjust screen tint - Press SM button on the remote control. Standard : Standard sound mode. Music : Music broadcasting mode. 7) Sharpness : Adjust screen sharpness Movie : Cinema broadcasting mode. News : News broadcasting mode. User : User’s customization mode. Also, it can be set in OSD menu if JOG button is used.
4-3 - Press Setting Option MENU button on the remote control to move to Main Menu. - Change the settings by using / button on the remote control. 5 Using PC MENU 5-1. Auto Adjustment 5-2. Setting Picture Sleep Timer - Press SLEEP button on the remote control. - Sleep timer can be set from Off to 180 minutes. Menu Timeout : It can be adjusted to display OSD Menu between 5 ~ 60 seconds. Menu Language : Change a language to display OSD. 5-3. Setting PC Scale Mode 5-4. Setting Sound 5-5.
5-1 Auto Adjustment 5-2 Setting Picture In case of using it as a PC monitor, it is automatically set. In case it is not optimally set even though automatically adjusting it, use Picture menu When the set is connected to a PC, the MODE should be set as PC RGB Mode. as below. - Press AUTO button on the remote control to automatically set the product’s screen status.
5-3 Setting PC Scale Mode When being used as a PC Monitor, the scale can be adjusted. 5-4 Setting Sound You can set sound suitable on PC mode. PC Monitor Scale works only when PC signal is connected and input signals are 1) Mode Setting selected in RGB mode. - Press SCALE on the remote control. 1:1 : Display the resolution as 1:1. Full : Display picture in the full screen re gardless of the resolution. Standard : Standard sound mode. Music : Music broadcasting mode.
5-5 - Press Setting Option MENU 5-6 button on the remote control to move to Main Menu. - Change the settings by using / button on the remote control. Setting Color Temperature You can set screen color temperature on PC mode. - Press MENU button on the remote control and move to menu . - Set the value among 5500, 7300, 9300 or you can set as your preference in USER. Sleep Timer - Press SLEEP button on the remote control. - Sleep timer can be set from Off to 180 minutes.
6 Specifications 6-1. Dimensions 6-2.
6-1 Dimensions 6-2 Specifications Dimensions, apparent design and specifications are subject to change without any prior notice for the performance improvement. 1) With Stand Product Name 20” TFT-LCD TV LCD Panel Type Amorphous Silicon TFT-LCD Size 20” (diagonal length) Resolution 1366 (H) x 768 (V) Pixel Pitch 0.324 mm x 0.324 mm Contrast Ratio 600 : 1 (Typ.
7 Service & Others 7-1.
7-1 Troubleshooting 2) PC Monitor-related Troubles No image on the monitor Before contacting service to service personnel, please check the followings first. Check whether the D-Sub cable is firmly connected to the TV and a PC. If you still have the same symptoms even after taking the following actions, contact your Check whether a graphic card is correctly inserted into the slot. local dealer or qualified service personnel. Check whether the Power of a PC and the TV is on.
This device comply with part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interference, and (2) This device must accept any interference that may cause undesired operation. This equipment has been tested and found to comply with the limit for a Class B digital Device pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
