DEClaser 3200 Printer Operator’s Guide Order Number: EK–DC32P–OP–001 Digital Equipment Corporation Maynard, Massachusetts
First Printing, September 1991 The information in this document is subject to change without notice and should not be construed as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no responsibility for any errors that may appear in this document. Any software described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.
FCC NOTICE: This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules, which are designed to provide reasonable protection against such interference in a residential installation.
Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xiii 1 Printer Components 1.1 1.2 Printer Components and Functions . . . . . . . . . . . . . . . . . . . . . . . Required Operating Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 1–8 2 Printer Operation 2.1 2.2 2.3 2.4 2.5 2.5.1 2.6 2.7 2.7.1 2.7.2 2.7.3 2.8 Printer Status Messages . . . . . . . . . . . . . . . . . PostScript Instructional Messages . . . . .
User Defaults Memory (NVRAM) . . . . . . . . . . . . . . . . System Memory Allocation for DEC PPL3 and LJ2D Protocols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3 Changing and Saving Menu Selections . . . . . . . . . . . . . . 4.4 Set Up Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.1 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.2 DEC PPL3 Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.2.
4.4.9 Serial Menu . . . . . . . . . . . . . . . . 4.4.9.1 Baud Rate . . . . . . . . . . . . . . 4.4.9.2 Parity . . . . . . . . . . . . . . . . . . 4.4.9.3 Flow Control . . . . . . . . . . . . 4.4.10 Display Language . . . . . . . . . . . 4.4.11 Communications Error Feature . 4.5 Test Menu . . . . . . . . . . . . . . . . . . . . 4.5.1 Printing the Configuration Sheet 4.5.2 Printing the Font Status Sheets 4.6 Defaults Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Service 8.1 Digital Equipment Corporation Services . . . . . . . . . . . . . . . . . . . 8–1 A DEC PPL3 Quick Reference Guide A.1 A.2 A.3 A.4 A.5 A.6 A.7 A.8 A.9 Unit Selection . . . . . . . . . . . . . . . . . . . . . . . . . . Spacing, Implicit Cursor Motion, Sheet Size and Tabs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Explicit Cursor Movement . . . . . . . . . . . . . . . . . Font Management and Attribute Selection . . . . Vectors . . . . . . . . . . . . . . . . . . . . .
E LN03 Compatibility E.1 E.2 E.3 General Differences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printable Area Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . DEC PPL3 Protocol Compatibility . . . . . . . . . . . . . . . . . . . . . . . . E–1 E–2 E–2 F Fonts for the DEClaser 3200 Printer F.1 F.2 F.3 F.3.1 F.3.2 F.4 F.5 F.5.1 F.5.2 Font Attributes . . . . . . . . . . . . . . . . . . . . . . . . . . Supported Font Cartridges . . . . . . . . . . . . . . . .
I Cabling Information I.1 I.2 I.2.1 I.2.2 Cable Combinations . . . . . . . . . . . . . Interface Programming Instructions Serial Flow Control . . . . . . . . . . Parallel Communication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I–1 I–4 I–4 I–5 Printer Components: Front View . . . . . . . . . . . . . Printer Components: Rear View . . . . .
6–1 6–2 Printer Paper Paths . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Paper Jam Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6–20 6–21 Printer Components: Front View . . . . . . . . . . . . . Printer Components: Rear View . . . . . . . . . . . . . Printer Components: Inside View . . . . . . . . . . . . Printer Status Messages . . . . . . . . . . . . . . . . . . . PostScript Messages . . . . . . . . . . . . . . . . . . . . . . .
4–24 4–25 4–26 4–27 4–28 4–29 4–30 4–31 4–32 4–33 4–34 4–35 4–36 4–37 4–38 4–39 4–40 4–41 4–42 4–43 4–44 4–45 4–46 4–47 4–48 5–1 5–2 5–3 5–4 6–1 6–2 6–3 8–1 A–1 A–2 B–1 B–2 x Symbol Set . . . . . . . . . . . . . . . . . . . . . . PostScript Memory Allocation . . . . . . . Duplex . . . . . . . . . . . . . . . . . . . . . . . . . Tumble . . . . . . . . . . . . . . . . . . . . . . . . . Paper Tray . . . . . . . . . . . . . . . . . . . . . . Tray Switching . . . . . . . . . . . . . . . . . . .
C–1 D–1 D–2 F–1 F–2 F–3 G–1 G–2 G–3 H–1 H–2 H–3 I–1 PostScript Operators on the DEClaser 3200 Printer . . . . . . Filenames and Contents for Example SETUP Modules . . . . ANSI_SETUPS Example Device Control Library Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Font Cartridge Characteristics . . . . . . . . . . . . . . . . . . . . . . . Printer Font Control Block for Proportional Fonts . . . . . . . . Font Access and Font Control Values . . . . . . . . .
Preface The DEClaser 3200 printer uses electrophotographic laser technology to print text and graphics. It has a print resolution of 300 x 300 dots per inch and prints at speeds up to 13 pages per minute in simplex mode, and 11 pages per minute in duplex mode. The printer consists of an engine (print mechanism) and a controller (formatter) that are driven from host-based software to provide shared printer access from the Digital network.
Options In addition to the standard features, the following options are available for the DEClaser 3200 printer: • A Legal-size paper cassette (8.5 in. x 14 in.) • An adjustable paper cassette designed to accept various paper sizes (accommodates widths from 182 mm to 216 mm (7.17 in. to 8.5 in.) and lengths from 254 mm to 356 mm (10 in. to 14 in.)) • An A4 or Letter-size large capacity input tray (holds up to 1500 sheets of 80 g/m2 (20 lb.
Software Requirements The availability of some features of the DEClaser 3200 printer depends on the operating and applications software used by the host computer system. For example, the DEClaser 3200 printer has the ability to print bold characters, but if your application program does not support bold printing, this feature would not be available. For information about the printer features you can use with your application program, consult your application program documentation.
The guide is organized as follows: xvi • Chapter 1, Printer Components, describes the components and functions of the DEClaser 3200 printer. • Chapter 2, Printer Operation, covers operating procedures such as powering the printer on and off and loading the paper cassettes. It also describes the printer status messages that are displayed during printer operation. • Chapter 3, The Control Panel, covers the use of the printer’s control panel.
• Appendix E, LN03 Compatibility, highlights some of the differences between the DEClaser 3200 printer and the LN03 family of printers. • Appendix F, Font Cartridge Information, contains information on how to access and use fonts from optional Digital ANSI-compliant font cartridges. • Appendix G, Accessories and Supplies, lists some of the accessories and supplies available for the DEClaser 3200 printer and explains how to order them.
Associated Documents Other manuals are available for use with the DEClaser 3200 printer. You can order these optional manuals from Digital as described in Appendix G. • Digital ANSI-Compliant Printing Protocol Level 3 Programming Reference Manual (AA–PBWGA–TE) This manual is for application programmers who create software that produces Digital ANSI-Compliant Printing Protocol level 3 output. It describes printer protocol character processing and printer control functions.
Conventions Used in This Guide The following terms and conventions are used in this guide: Convention Meaning NOTE Notes provide important additional information. CAUTION Cautions provide information required to prevent damage to equipment. WARNING Warnings provide information to prevent personal injury. Dash (–) A statement preceded by a dash describes the result of a procedural step. For example: 1. Insert the paper cassette into the printer. The Error indicator shuts off.
Safety Information The DEClaser 3200 printer complies with all United States government safety regulations applicable to laser beam light exposure. Read the following information to become familiar with laser safety. Laser Safety The DEClaser 3200 printer complies with 21 CFR Chapter 1, Subchapter J, as a Class 1 laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968.
1 Printer Components This chapter describes the components of the DEClaser 3200 printer and their functions. This chapter also provides information about the operating space required to perform day-to-day printing operations. 1.1 Printer Components and Functions This section points out the various printer components of the DEClaser 3200 printer.
Figure 1–1 Printer Components: Front View 1 2 7 3 4 5 6 MLO-006248 1–2 Printer Components
Table 1–1 Printer Components: Front View Component Function 1 Top Cover Release Lever Lifting this lever unlocks the top cover so it can be opened to clear paper jams or to perform printer maintenance. 2 Control Panel The control panel consists of a graphic display, a message display, indicator lights, and function keys. It provides information on printer status and can be used to perform certain printer functions, such as printing the last page of a document or accessing the printer menus.
Figure 1–2 Printer Components: Rear View 9 1 8 2 7 6 5 3 4 MLO-006249 1–4 Printer Components
Table 1–2 Printer Components: Rear View Component Function 1 Left-Side Cover The left-side cover opens to remove paper jammed in this area, and to perform user maintenance (fuser wick replacement). Paper reverses direction in this area when the printer is in duplex mode. 2 Upper and Lower Paper Cassettes The paper cassettes automatically feed paper to the printer. Each cassette can hold up to 250 sheets of 80 g/m2 basis weight (20 lb.) paper. See Section 2.
Figure 1–3 Printer Components: Inside View 2 1 3 4 5 MLO-006460 1–6 Printer Components
Table 1–3 Printer Components: Inside View Component Function 1 Transfer/Separation Charger The transfer/separation charger places a high positive charge on the paper which attracts the toner image from the photoreceptor drum onto the paper as it passes by. You replace the charger periodically (at the same time as the developer cartridge) using the replacement instructions included in the kit.
1.2 Required Operating Space Figure 1–4 shows the minimum amount of space required to perform daily operations. See Appendix H for additional information on environmental conditions that must be met in order for the printer to operate properly. Figure 1–4 Operating Space B C A Option: MMF or LCIT F D E A 19.3 in 49.0 cm B 7.5 in 19.0 cm C 30.3 in 76.9 cm D 24.4 in 61.9 cm E* 67.6 in 171.7 cm F* 51.6 in 131.1 cm *These are the minimum operation dimensions.
2 Printer Operation This chapter provides the information necessary to perform day-to-day printer operations. It covers typical tasks, such as interpreting the printer status messages, powering the printer on and off, adding paper, and manual feed operation. 2.1 Printer Status Messages During normal printing operations the printer status is shown in the upper left corner of the message display (Figure 2–1). These status messages let you see the current state of the printer at a glance.
The printer status messages are shown and described in Table 2–1. Table 2–1 Printer Status Messages Status Message Meaning READY The printer is online, ready to receive and print data. PAUSED The printer is paused and not able to print data. Data can still be received until the printer communications buffer is full. To exit the paused state and place the printer back on line, press Online/Pause . BUSY The printer is receiving, processing, or printing data.
Table 2–1 (Cont.) Printer Status Messages Status Message Meaning POWER SAVER ON This message is displayed after the printer has been idle for 2 hours. The fusing unit heater is turned off when the printer is in the power saver state. The printer automatically exits the power saver mode under either of the following conditions: • The printer receives a print job from the host or from the control panel (for example, printing the configuration sheet). • Any printer cover is opened and then closed.
2.3 Turning the Printer On Turn the printer on using the following procedure. 1. Press the power switch on the back of the printer to the | (ON) position. MLO-006273 You should observe the following when you turn the printer on: All control panel indicators light for a moment. The Online indicator flashes while the printer is warming up, and performs a power-on diagnostic test. Diagnostic code numbers shown on the display change as the test is performed.
2.4 Turning the Printer Off Turn the printer off using the following procedure. 1. Be sure the printer is not printing and that the Last Page indicator is not on. Turning the printer off during printing causes paper jams and loss of data. Turning the printer off while the Last Page indicator is on causes the last page of data in the print buffer to be lost. 2. Press the power switch on the back of the printer to the O (OFF) position.
2.5 Guidelines for Loading Paper The DEClaser 3200 printer comes standard with either two A4-size (210 mm x 297 mm) or two Letter-size (8.5 in. x 11 in.) paper cassettes, depending on the model ordered. Each paper cassette can hold up to 250 sheets of 80 g/m2 basis weight (20 lb.) paper. Here are some general guidelines to follow about the paper used in the printer. • Use only high-quality paper as specified in Chapter 5. • Do not use any paper that is creased, folded, clipped, stapled, or damaged.
2.5.1 Loading Single-Size Paper Cassettes Each paper cassette can hold up to 250 sheets of 80 g/m2 basis weight (20 lb.) paper. Be sure to use high-quality paper such as those listed in Appendix G, to limit paper jams and ensure good print quality. Do not attempt to alter the cassette to accommodate a different paper size, as this will cause paper jams. For information about the paper sizes that the optional adjustable paper cassette can accommodate, see Section 4.4.6.
Adding Paper to the Cassette This section describes how to add paper to the cassettes. NOTE If you are changing to a new cassette size, you must perform a printer reset after inserting the new cassette. See Section 4.6 for information about the printer reset feature. 1. Make sure the printer has stopped printing, or that the printer status reads PAUSED, before removing the paper cassette.
2. Remove the cassette from the printer by lifting it up slightly and then pulling it straight out from the printer. The Supplies indicator lights. 26.
3. Lift the cassette cover open.
4. Press down the lifting plate to lock it in the loading (lowered) position.
5. Tap a stack of paper on a flat surface to align the edges.
6. Insert the paper into the cassette, making sure the stack is below the paper snubbers. To prevent paper jams, do not load paper above the MAX limit line. Load prepunched paper with the holes facing the front of the printer. For simplex printing: load forms and letterhead paper facedown, with the top edge inserted first. For duplex printing: load forms and letterhead paper faceup, with the bottom edge inserted first. Paper Snubber 26.
7. Close the paper cassette cover and insert the cassette into the printer. The Error indicator goes off (if it was on). The Supplies indicator goes off. 26.
2.6 Adjustable Paper Cassette Size Selection An adjustable paper cassette is designed to accept various paper sizes. It can accommodate widths from 182 mm to 216 mm (7.17 in. to 8.5 in.), and lengths from 254 mm to 356 mm (10 in. to 14 in.). When you use a standard single-size paper cassette, the printer knows the paper size because the cassettes are keyed to the paper size they contain.
Table 2–4 Example of Setting the Adjustable Cassette Size Operation Display Reads 1. Press Online/Pause to pause the printer. PAUSED (printer status) The Online indicator goes off. 2. Press Set Up to enter the SET UP menu. SET UP MENU PROTOCOL until you reach 3. Press the ADJ CASSETTE feature. SET UP MENU ADJ CASSETTE to enter the 4. Press ADJ CASSETTE feature. ADJ CASSETTE CASSETTE A to select the 5. Press CASSETTE A value. CASSETTE A LETTER 6. Press until you reach the LEGAL paper size.
2.7 Manual Feed Operation The printer has a manual feed tray that can accept paper, transparencies, labels, and envelopes. This section describes how to use the manual feed tray. NOTE The manual feed tray is not available if the multi-media feeder is installed. The manual feed tray can accommodate various media sizes from 105 mm ~ 257 mm (4.13 in. ~ 10.12 in.) wide, and from 191 mm ~ 364 mm (7.5 in. ~ 14.33 in.) long.
When feeding media manually, you must specify the paper size you are using, either through your application program or by using printer commands. NOTE The paper size cannot be selected using the control panel if you are using DEC PPL3 protocol; it must be sent using software from the host system. The paper size can be selected if you are using LJ2D protocol, or the optional PostScript protocol. Envelopes and labels have the same setup requirements as all other media.
Table 2–5 Selecting Manual Feed Mode Operation Display Reads 1. Press Online to pause the printer. PAUSED (printer status) TRAY 1 (tray selection) The Online indicator goes off. 2. Press Set Up to enter the SET UP menu. SET UP MENU PROTOCOL to enter 3. Press the PROTOCOL feature. PROTOCOL DEC PPL3 4. Press to enter the DEC PPL3 menu. DEC PPL3 * TRAY SELECTION to enter the 5. Press TRAY SELECTION feature. TRAY SELECTION TRAY 1 * 6. Press until you reach the MANUAL value.
2.7.2 Feeding Paper, Transparencies, and Labels Manual feed mode must be selected before you can feed media in the manual feed tray. When manual feed mode is selected, the tray selection on the message display reads MANUAL (for DEC PPL3 and LJ3D protocols), or MAN/MMF (for the optional PostScript protocol). If you need to select the manual feed mode of operation, see Section 4.4.2.1 (DEC PPL3), Section 4.4.3.2 (LJ2D), or Section 4.4.5.
1. Open the manual feed tray (if necessary).
2. Insert a single sheet of paper into the tray until it stops and is picked up by the feed rollers. Align the paper against the paper guide on the feed tray. Insert letterhead paper and pre-printed labels faceup, with the top edge first. Insert blank labels faceup. Insert prepunched paper with the holes facing the front of the printer. The paper is automatically fed into the printer.
2.7.3 Feeding Envelopes Manual feed mode must be selected before you can feed media in the manual feed tray. When manual feed mode is selected, the tray selection on the message display reads MANUAL (for DEC PPL3 and LJ3D protocols), or MAN/MMF (for the optional PostScript protocol). If you need to select the manual feed mode of operation, see Section 4.4.2.1 (DEC PPL3), Section 4.4.3.2 (LJ2D), or Section 4.4.5.
Use the following procedure to load envelopes in the manual feed tray. 1. Open the manual feed tray.
2. Insert a single envelope (faceup) into the tray until it stops and is picked up by the feed rollers. Align the top edge of the envelope against the paper guide on the feed tray. The envelope is automatically fed into the printer. The printer prompts you to insert another envelope (error message, alarm, and so on) if there are additional addresses to print.
2.8 Adjusting the Print Density Print density is the term used to describe the amount of toner applied to the paper. The print density adjustment knob regulates the amount of toner applied to the paper to produce a slightly lighter or darker print. You can extend the life of a toner cartridge by using the lightest possible print density setting that gives you acceptable print quality. NOTE The toner cartridge life is approximately 6,000 A4 or letter-size pages.
Use the following procedure to adjust print density. 1. Open the top cover by lifting up its release lever.
2. Rotate the adjustment knob clockwise to make the print darker, or counter-clockwise to make the print lighter.
3. Close the top cover by pushing it down until it latches securely in place. MLO-006492 Continue printing and check the results of the new density setting. If the results are not to your satisfaction, readjust the print density as necessary.
3 The Control Panel The control panel shows you the status of the DEClaser 3200 printer. It consists of a graphic display, a message display, indicator lights, and function keys. While your host computer typically provides most of the communication to the printer, the control panel allows you to perform certain printer functions, such as configuring the printer menus, or printing a page of data that remains in the print buffer. This chapter explains the features and uses of the control panel.
Figure 3–1 Control Panel 1 2 4 3 Set Up 5 Last Page 6 Supplies Test 7 Error Online Defaults Online/Pause * 8 9 10 11 12 MLO-006463 Table 3–1 Control Panel Functions 1 Item Function Graphic Display The graphic display is an outlined image of the printer. Light emitting diodes (LEDs) at various locations on the image light to indicate paper tray selections, paper jam locations, and consumable replacement location. The paper tray LEDs are green; all other LEDs are red.
Table 3–1 (Cont.) Control Panel Functions 2 Item Function Message Display The message display is used to show different types of information, depending on whether the printer is in Operating Mode or Menu Mode. Operating Mode: The message display typically shows the current printer status, protocol, tray selection, and whether printing in simplex or duplex mode during printer operation (see Figure 3–2).
Table 3–1 (Cont.) Control Panel Functions Item 3 Set Up / Function This is a dual-function menu key and functions only when the printer is paused. It performs a different task, depending on whether the printer is in Operating Mode or Menu Mode. Operating Mode: Pressing Set Up enters the SET UP menu which contains printer configuration features such as protocol, tray selection, and communications interface. See Section 4.4 for information about the features in the SET UP menu.
Table 3–1 (Cont.) Control Panel Functions 5 Item Function Supplies Indicator (yellow) The Supplies indicator works in conjunction with inform you that: to • A consumable cartridge is nearing the end of its useful life and needs to be reordered. • A consumable cartridge has reached its end of life and needs to be replaced. • The selected tray has run out of paper and needs to be refilled. • When a nonselected paper tray is not installed. • When NO OFFSET is selected.
Table 3–1 (Cont.) Control Panel Functions 7 Item Function Online Indicator (green) The Online indicator works in conjunction with Online/Pause to indicate when the printer is on line. On: The printer is on line and controlled by the host computer (printer status reads READY). The host computer can send data to print, as well as commands to control the printer. Off: The printer is paused (printer status reads PAUSED) and not able to print any more data.
Table 3–1 (Cont.) Control Panel Functions Item 9 > Function This is a dual-function key and performs a different task, depending on whether the printer is in Operating Mode or Menu Mode. Operating Mode: Works in conjunction with the Last Page indicator. Press > when the Last Page indicator is on to print the last page of data remaining in the print buffer. Menu Mode: Pressing > advances you to the next menu or feature. This key scrolls through each of the menus or features, and then repeats the cycle.
Table 3–1 (Cont.) Control Panel Functions Item Function 11 Defaults Pressing Defaults selects the Defaults menu when the printer is paused. The Defaults menu contains selections to recall factory and user defaults, or to save currently selected features in user defaults. See Section 4.6 for information about the features in the Defaults menu. 12 Online/Pause This is a dual-function key and performs a different task, depending on whether the printer is in Operating Mode or Menu Mode.
Figure 3–2 shows an example of printer status information displayed when the printer is in Operating Mode. Figure 3–2 Operational Information Status Message Protocol Set Up READY TRAY 1 DEC SIMPLEX Last Page Supplies Test Error Online Defaults Online/Pause * Tray Selection Print Mode MLO-006480 Figure 3–3 shows an example of error information displayed when the printer is in Operating Mode.
Figure 3–4 shows an example of menu information displayed when the printer is in Menu Mode. Figure 3–4 Menu Information Set Up SET UP MENU ALARM Feature * Last Page Supplies Test Error Online Defaults Online/Pause * Selection Indicator MLO-006482 Figure 3–5 shows an example of feature information displayed when the printer is in Menu Mode.
4 Printer Menus This chapter describes the use of the printer menus to configure, test, and save or recall default selections when the printer is in Menu Mode. These menus allow you to customize the printer to your specific host computer and software applications. The DEClaser 3200 printer has three main menus: The Set Up Menu The Set Up menu is used to configure the printer by selecting operating parameters (protocol, communications, and so on). These operating parameters are known as features and values.
4.1 Entering Menu Mode When configuring any of the printer menus, the printer is said to be in Menu Mode. When the printer is in Menu Mode, the keys labeled with symbols on them take on a secondary Menu Mode function (see Section 4.1.1). Table 4–1 describes how to select a printer menu. NOTE This procedure assumes that the factory default settings are the current selections in operating memory. Table 4–1 Selecting a Printer Menu Operation Resulting Display Reads 1.
4.1.1 Key Functions in Menu Mode When the printer is in Menu Mode, the keys labeled with symbols are used to access different menus, features, and values. Table 4–2 describes the function of these keys. After reading these descriptions, try using the keys to better understand their operation. See Section 4.3 for an example of how to use the Menu Mode keys to configure the printer.
Figure 4–1 Menu Information Set Up SET UP MENU ALARM Feature * Last Page Supplies Test Error Online Defaults Online/Pause * Selection Indicator MLO-006482 Figure 4–2 Feature Information Feature Set Up ALARM ONCE Value * Last Page Supplies Test Error Online Defaults Online/Pause * Selection Indicator MLO-006483 4–4 Printer Menus
4.
Figure 4–3 Operating Flow ROM NVRAM Recall Factory Defaults RAM Recall User Defaults Power On Printer Save Defaults Operating Memory (Contains Current Printer Settings) Commands (Host Computer) Menu Operations (Control Panel) RAM Cleared at Power-Off (Can Be Changed) ROM Not Cleared at Power-Off (Cannot Be Changed) NVRAM Not Cleared at Power-Off (Can Be Changed) MLO-006465 4–6 Printer Menus
4.2.1 Operating Memory (RAM) When the printer is powered on, it loads the values stored in user defaults memory (NVRAM) into the operating memory (RAM). The printer operates using these values. When you select new values (through commands or from the control panel), they are placed in the operating memory and become part of the printer settings currently in use. Because RAM is temporary, any changes made to the settings in the operating memory are lost if the printer is reset or powered off.
4.2.4 System Memory Allocation for DEC PPL3 and LJ2D Protocols The DEClaser 3200 comes with 1 MB of system memory. The printer allocates system memory dynamically when font files are downloaded from an application, and when bitmap allocation is required for page imaging. The printer also reserves a portion of this memory for use by the printer firmware. For most applications, dynamic allocation of standard and optional configurations of system memory by the printer is acceptable.
Table 4–3 System Memory Allocation Number of Optional 2 MB SIMMS Total System Memory Application Support Provided 0 1 MB (standard) Most simplex printing is possible, but complex pages cannot be guaranteed. Complex print jobs may cause page breaks. 1 3 MB Most simplex printing is possible and can be guaranteed on Letter, A4, and Legal-size paper. Duplex printing is possible but cannot be guaranteed. For additional information about allocating memory, see Section 4.4.2.
4.3 Changing and Saving Menu Selections Table 4–4 illustrates how to change operating parameters in the Set Up menu, and then save them using the Defaults menu. In this example you perform the following tasks: • Select the Set Up menu. • Change the baud rate from 9600 bits/second to 19200 bits/second. • Select the Defaults menu. • Save the new value in NVRAM. • Select the Test menu. • Print the configuration sheet to verify the new baud rate. • Exit Menu Mode and return the printer on line.
Operation Resulting Display Reads 6. Press to enter the BAUD RATE feature. BAUD RATE 9600 until you 7. Press reach 19200 baud. BAUD RATE 19200 to select 8. Press 19200 baud. BAUD RATE 19200 until you 9. Press exit Menu Mode. PAUSED TRAY 1 10. Press Defaults to enter the DEFAULTS menu. DEFAULTS MENU PRINTER RESET until you 11. Press reach SAVE DEFAULTS. DEFAULTS MENU SAVE DEFAULTS to select 12. Press SAVE DEFAULTS. DEFAULTS MENU SAVE DEFAULTS * (The asterisk appears momentarily.
16. Press Online/Pause to exit Menu Mode and place the printer back on line. READY TRAY 1 DEC SIMPLEX The Online indicator lights. 4.4 Set Up Menu You configure the DEClaser 3200 printer by selecting an appropriate set of values from the Set Up menu. Once values are selected, you can save them in NVRAM using the Defaults Menu (Section 4.6). Saving features in NVRAM allows you to retain the printer settings so that they need to be configured only once.
PROTOCOL ALARM ADJ CASSETTE CASSETTE A CASSETTE B COMM INTERFACE * SERIAL * ONCE 3 TIMES DISPLAY LANGUAGE COMM ERROR CONTINUE * HALT PARALLEL CONTINUOUS DISABLED * 8 X 10 EXECUTIVE 215 X 275 LETTER A4 215 X 315 210 X 230 8 X 13 8.
4.4.1 Protocol This feature lets you select the printing protocol that matches your particular system. The protocol selections are secondary menus and contain features and values of their own. You must select the proper protocol operating parameters from these secondary menus. Table 4–5 describes the protocol selections. Table 4–5 Protocol Feature PROTOCOL Menu DEC PPL3 Description 1 This is the Digital ANSI-Compliant Printing Protocol Level 3 menu. Select this menu when running ANSI applications.
TRAY SELECTION * DUPLEX TRAY 1 TRAY 2 TRAY 3 (if installed) TRAY 1-2 TRAY 1-3 (if tray 3 is installed) TRAY 2-3 (if tray 3 is installed) TRAY 1-2-3 (if tray 3 is installed) MANUAL MMF (if installed) * MEMORY MGMT AUTO WRAP * ON OFF * PARTIAL FULL EXT FULL DUAL FULL DUAL FULL EXT NEW LINE USER PREF SET DEVICE ID POWER-UP MESSAGE LN03 ON * OFF * DEC PPL3 * ON OFF CTRL REPN MODE * ON OFF DEC SUPPLMT SET * ISO LATIN-1 JIS KATAKANA DEC HEBREW ISO LAT HEBREW HOST DEFINED SIMPLEX NORMAL DUPL
4.4.2.1 Tray Selection The tray selection feature allows you to select the tray that feeds paper to the printer. In addition to selecting a singular tray, a collection of trays can be selected to enable failover. NOTE When printing in duplex mode, you cannot add paper to TRAY 1 while printing from another tray. TRAY 1 must be installed to print in duplex mode. This menu also contains selections for the optional large capacity input tray and the multi-media feeder (TRAY 3).
4.4.2.2 Duplex The duplex feature controls whether the DEClaser 3200 printer images data on one side of a sheet (called simplex printing), on both sides of the sheet (called duplex printing). The duplex feature can also perform more sophisticated printing modes, such as printing single-sided masters for double-sided reproduction at a later time. The number and orientation of logical pages on physical sheets of paper is called the page layout.
Tumbling The tumbling component of the print mode defines the binding edge of the physical sheet. Normal documents are designed to be bound along the long edge of the sheets. The top edge of the first page (side 1), is aligned with the top edge of the second page (side 2). For example, this manual is printed in duplex normal. Tumbled documents are designed to be bound along the short edge of the sheets.
Table 4–8 Duplex Feature Values Description Illustration DUPLEX SIMPLEX NORMAL1 Selects true simplex normal operation; binding is on the long edge. Figure 4–7 DUPLEX NORMAL Selects true duplex normal operation; binding is on the long edge. Figure 4–7 SIMPLEX TUMBLED Selects true simplex tumbled operation; binding is on the short edge. Figure 4–7 DUPLEX TUMBLED Selects true duplex tumbled operation; binding is on the short edge.
Figure 4–6 Duplex Input Input: 1 1 2 2 3 3 Sheet Sheet Sheet 1 1 2 2 3 3 4 (Newsheet) 4 5 5 Sheet Sheet 4 4 5 5 MLO-005380 4–20 Printer Menus
Figure 4–7 Duplex and Simplex Output True Simplex Normal: 1 1 2 2 3 3 4 4 5 5 Sheet Sheet Sheet Sheet Sheet 2 3 3 2 2 3 3 4 4 5 5 4 1 4 1 5 5 True Simplex Tumbled: 2 1 2 1 Sheet 3 3 3 3 4 Sheet Sheet 4 1 Sheet 2 1 Sheet 5 5 True Duplex Normal: 1 1 4 4 Sheet 4 and 5 Sheet Sheet 3 and Blank 5 Sheet 1 and 2 Blank Sheet Sheet Sheet 2 Sheet True Duplex Tumbled: 1 1 3 3 4 4 Sheet 4 and 5 Sheet Sheet 3 and Blank 5 Sheet 1 and 2 Blank Sheet
Figure 4–8 Duplex Master and Simplex Compressed Output Duplex Master Normal: 1 1 2 2 3 3 4 4 5 5 Sheet Sheet Sheet Blank Sheet Sheet 2 2 3 3 4 4 5 2 1 3 3 4 4 5 1 5 Duplex Master Tumbled: 3 3 3 3 4 5 2 2 1 Sheet 4 5 Sheet 1 Sheet Blank Sheet Sheet 2 1 5 1 Simplex Compressed Normal: 1 1 5 5 Sheet 5 and Blank Blank Sheet 3 and 4 Sheet Sheet 1 and 2 4 Sheet Sheet Sheet 2 Sheet Simplex Compressed Tumbled: 3 3 5 5 Sheet 1 and 2 Sheet 3 and 4
4.4.2.3 Memory Management The memory management feature allows you to instruct the printer to reserve memory space for one or two full bitmap pages, or not to reserve any bitmapped memory space for page printing. Since printer memory is shared with both fonts and graphics, it is usually desirable to let the printer allocate the memory dynamically, because even full page bitmap images often print when partial memory is selected. For additional information about system memory allocation, see Section 4.2.4.
4.4.2.4 Auto Wrap The auto wrap feature determines whether text wraps to the next line when it reaches the right margin. Table 4–10 describes the auto wrap selections. Table 4–10 Auto Wrap Feature Values Description AUTO WRAP ON1 When the print position exceeds the right margin, it wraps to the left margin of the next line. OFF Text is not wrapped to the next line when the right margin is exceeded. Text beyond the right margin is lost. 1 Factory default setting 4.4.2.
4.4.2.6 User Preference Set The user preference set defines the supplemental character set appropriate for your application or system. Table 4–12 lists the Digital supported character sets.
4.4.2.7 Device Identification The DEClaser 3200 printer can identify itself as a Digital ANSI-Compliant Printing Protocol Level 3 printer (DEC PPL3), and therefore can be recognized as such by symbionts and terminal drivers that conform to the Digital ANSIcompliant architecture. This identification is also compatible with level 2 devices, since all level 2 sequences are also supported. You can also select an LN03 identification for applications that require the printer to identify itself as an LN03 printer.
4.4.2.9 Control Representation Mode This feature enables the printer to stop interpreting control characters, and print out unprocessed data or commands from the host computer in control representation form. The printing of unprocessed data (with control characters embedded in the file) is convenient for debugging problems. Table 4–15 describes the control representation mode values.
COPIES * TRAY SELECTION PAPER DUPLEX FONT NUMBER SIZE 1-99 1 ORIENTATION 1-512 * *1 PORTRAIT LANDSCAPE FORM LENGTH PAGE BUFFERS SYMBOL SET 5-128 * 60 DISABLED * LONG BINDING SHORT BINDING * * LETTER LEGAL TRAY 1 TRAY 2 TRAY 3 (if installed) TRAY 1-2 TRAY 1-3 (if tray 3 is installed) TRAY 2-3 (if tray 3 is installed) TRAY 1-2-3 (if tray 3 is installed) MANUAL MMF (if installed) EXECUTIVE A4 COMM 10 MONARCH DL C5 * 1PARTIAL FULL 1 FULL LONG 2 FULL 2 FULL LONG * ROMAN-8 ECMA94 PC8 PC8D PC
4.4.3.1 Copies The copies feature determines how many copies of each page are to be printed. This feature does not collate print jobs; it prints the requested number of copies of each page in the job (see Table 4–16). NOTE Use Use Use Use to enter the feature, and to select the new value. to increase the numeric value. to decrease the numeric value. to move from one digit to the next. Table 4–16 Copies Feature Values Description COPIES 011 —99 Sets the number of copies to print.
Table 4–17 Tray Selection Feature TRAY SELECTION Values Description 1 TRAY 1-2 Feeds paper from TRAY 2 when TRAY 1 is empty. MANUAL Selects the manual feed mode of operation (see Section 2.7). MMF2 Feeds paper from the optional MMF. TRAY 1 Feeds paper from the upper paper cassette. TRAY 2 Feeds paper from the lower paper cassette. TRAY 33 Feeds paper from the optional LCIT. TRAY 1-3 3 Feeds paper from TRAY 1 when TRAY 3 is empty. TRAY 2-33 Feeds paper from TRAY 2 when TRAY 3 is empty.
4.4.3.3 Duplex The duplex feature controls whether the DEClaser 3200 printer images data on one side of a sheet (called simplex printing), or on both sides of the sheet (called duplex printing). Table 4–18 Duplex Feature Values Description DUPLEX DISABLED1 Selects the simplex mode of operation. LONG BINDING Selects the duplex mode of operation; binding is on the long edge. SHORT BINDING Selects the duplex mode of operation; binding is on the short edge. 1 Factory default setting 4.4.3.
4.4.3.5 Paper Size The paper size feature defines the default paper size. The printer feeds paper from a tray defined in the tray selection sequence (Section 4.4.3.2) matching the default size selected. If the printer cannot locate a tray that matches the default size, an error messsage is displayed. See Section 6.4 for additional information about paper tray error messages. Table 4–20 lists the paper size selections. Table 4–20 Paper Size Feature PAPER SIZE 1 Values LETTER Description 1 Selects 8.5 in.
4.4.3.7 Form Length The form length feature sets the number of lines to print on the page. Typical form length settings are 60 lines per page for Letter-size paper, and 78 lines per page for Legal-size paper. These settings are based on 6 lines per inch after subtracting 1 inch from the page length to allow for space at the top and bottom of the page. For example, to set Legal-size paper to 6 lines per inch you would take the page length (14), minus the top and bottom space (1), and come up with 13.
4.4.3.8 Page Buffers The page buffers feature allows you to instruct the printer to reserve memory space for one or two full bitmap pages, or not to reserve any bitmapped memory space for page printing. Since printer memory is shared with both fonts and graphics, it is usually desirable to let the printer allocate the memory dynamically, because even full page bitmap images often print when partial memory is selected. For additional information about system memory allocation, see Section 4.2.4.
4.4.3.9 Symbol Set The symbol set defines the character set to be used with the selected font. These symbol sets are designed to accommodate specific applications or language requirements. For example, the SPANISH character set contains symbols that apply specifically to the Spanish language.
4.4.4 PostScript Menu This section describes the features and values in the PostScript protocol menu. Figure 4–10 shows a block diagram of the PostScript protocol menu. PostScript is displayed as the protocol selection only when the PostScript option is installed and activated. If the option is not installed, POSTSCRIPT will not be shown as a protocol selection.
Font Cache Frequently used characters can be stored in machine memory for re-use, improving overall printer performance. If your documents use a large variety of type styles or sizes, a larger font cache can improve performance markedly. Use Table 4–25 as a guide to determine how much additional memory is required to enhance printer performance for your particular application. Optional memory can be purchased in 2 MB single in-line memory modules (SIMM’s). See Appendix G for ordering information.
DUPLEX * ON OFF TUMBLE * PAPER TRAY TRAY SWITCHING ON OFF * * TRAY SWITCH SEQ ON OFF TRAY 1 TRAY 2 TRAY 3 (if installed) MANUAL * MAN/MMF SIZE TRAY 1 TRAY 2 TRAY 3 (if installed) TRAY 1-2 TRAY 1-3 (if tray 3 is installed) TRAY 2-3 (if tray 3 is installed) TRAY 1-2-3 (if tray 3 is installed) OUTPUT OFFSET * ON OFF START WAIT TIMEOUT PAGE * JAM RECOVERY ON OFF * ON OFF ALLOW JOB RESET * ON OFF ASYN CTRL MODE * ON OFF 20 SECONDS 40 SECONDS * 60 SECONDS * LETTER A4 EXECUTIVE B5
4.4.5.1 Duplex The duplex feature controls whether the printer writes data on one side of a sheet (called simplex printing), or on both sides of the sheet (called duplex printing). Table 4–26 Duplex Feature Values Description DUPLEX ON Selects the duplex mode of operation. OFF 1 1 Selects the simplex mode of operation. Factory default setting 4.4.5.2 Tumble The tumble feature determines if the page is to be bound on the short edge of the paper.
4.4.5.3 Paper Tray The paper tray feature allows you to select the tray that feeds paper to the printer. This menu contains selections for the optional large capacity input tray (LCIT) and the multi-media feeder (MMF). The MANUAL/MMF value is displayed whether you are using the manual feed tray or the MMF. Table 4–28 lists the tray selections. Table 4–28 Paper Tray Feature PAPER TRAY Values Description 1 TRAY 1 Paper feeds from the upper paper cassette.
4.4.5.4 Tray Switching The tray switching feature is used in conjunction with the TRAY SWITCH SEQ feature described in Section 4.4.5.5 to designate if the paper tray fail-over sequence is enabled. Table 4–29 Tray Switching Feature Values Description TRAY SWITCHING ON Enables the TRAY SWITCH SEQ feature allowing paper tray fail-over to occur. OFF1 Disables TRAY SWITCHING so that the TRAY SWITCH SEQ feature cannot be activated. 1 Factory default setting 4.4.5.
The TRAY SWITCH SEQ feature establishes that the failover order of the paper trays will occur when TRAY SWITCHING = ON (see Section 4.4.5.4). If TRAY SWITCHING = OFF, the TRAY SWITCH SEQ feature does not function. Table 4–30 lists the tray selections.
4.4.5.6 Manual/Multi-Media Feeder Size MAN/MMF SIZE indicates the paper size when using the manual feed tray, or the paper size used in the multi-media feeder if it is installed. The page is formatted to the size selected, regardless of the actual paper size used. This feature only functions when the paper tray selection is MAN/MMF (Section 4.4.5.3). For information about feeding paper manually, see Section 2.7.
4.4.5.7 Output Offset The output offset feature allows PostScript jobs to use the output tray offset positioning feature to separate the jobs as they are printed. Table 4–32 Output Offset Feature Values Description OUTPUT OFFSET ON Enables the output tray offset feature to separate print jobs. OFF1 Disables the output tray offset feature; print jobs will not be separated. 1 Factory default setting 4.4.5.
4.4.5.9 Start Page The start page feature determines whether the PostScript start page is printed each time the PostScript protocol is activated. The start page shows the fonts available, and lists all of the current settings for the PostScript menu (Figure 4–11). Table 4–34 Start Page Feature Values Description START PAGE ON1 The start page is printed when the PostScript protocol is activated. OFF The start page is not printed when the PostScript protocol is activated.
Figure 4–11 Start Page MLO-007000 4–46 Printer Menus
4.4.5.10 Jam Recovery The jam recovery feature ensures the printer’s recovery from paper jams without losing data. This means the printer will automatically reprint any pages that jammed, and the host will not have to resend the job. For information about memory allocation and how it affects jam recovery, see PostScript Memory Allocation under Section 4.4.4. Table 4–35 Jam Recovery Feature Values JAM RECOVERY ON OFF1 1 Description Ensures recovery from paper jams without losing data.
4.4.5.11 Allow Job Reset The allow job reset feature described in Table 4–36 enables you to reset (abort) the current print job being processed from the control panel. Table 4–37 describes the procedure to abort a print job from the control panel. NOTE The current print job can always be aborted from the host, regardless of the ALLOW JOB RESET setting. Table 4–36 Allow Job Reset Feature Values Description ALLOW JOB RESET ON1 Allows you to abort a print job from the control panel.
4.4.5.12 Asynchronous Control Mode The asynchronous control mode feature determines whether the CTRL C and CTRL T codes are handled synchronously within the data stream, or asynchronously at the communications handler. Table 4–38 Asynchronous Control Mode Feature ASYN CTRL MODE 1 Values 1 Description ON Control codes are handled asynchronously. OFF Control codes are handled synchronously. Factory default setting 4.4.
Table 4–39 Adjustable Paper Cassette Sizes Feature Values Description 1 Selects 8.5 in. x 11 in. paper size CASSETTE A LETTER or A4 Selects 210 mm x 297 mm paper size CASSETTE B 215 X 315 Selects 215 mm x 315 mm paper size 1 210 X 330 Selects 210 mm x 330 mm paper size 8 X 13 Selects 8 in. x 13 in. paper size 8.5 X 13 Selects 8.5 in. x 13 in. paper size LEGAL Selects 8.5 in. x 14 in. paper size 8 X 10 Selects 8 in. x 10 in. paper size EXECUTIVE Selects 7.25 in. x 10.5 in.
4.4.8 Communications Interface The DEClaser 3200 printer supports both parallel and serial interface connections. The interface must match the type used by the host computer as described in Table 4–41. You cannot make communications interface selections using commands from the host computer. All values must be selected from the control panel. Once you make the selections, save them in NVRAM so that they will be activated (loaded into operational memory) each time the printer is powered on (see Section 4.6).
4.4.9 Serial Menu The Serial menu contains the features used to interface with the host using a serial interface. Make selections from this menu when SERIAL has been selected from the Communications Interface feature, Section 4.4.8. 4.4.9.1 Baud Rate The baud rate feature is used to set the printer transmit and receive speed used to communicate with the host computer. The printer speed must match the speed used by the host computer.
4.4.9.2 Parity The parity feature determines the format the printer uses to communicate with the host computer. The first part of the value (7 or 8) is the number of data bits the printer expects to see in each character it receives. The second part of the value is the type of parity bit the printer looks for in each character. A parity check is a method used to detect errors when data is sent over a communications line.
4.4.9.3 Flow Control The flow control feature selects the method used to regulate the flow of data to the input buffer of the printer and to the host. The XON/XOFF value uses software to regulate the flow of data to the input buffer of the printer. It is sometimes referred to as software handshaking protocol, a method the printer and the host computer use to exchange on/off signals. These signals prevent the input buffer from overflowing with data.
4.4.10 Display Language The language feature lets you display messages in any of the languages listed in Table 4–45. Status messages, error messages, printer menus, and the configuration sheet are displayed in the selected language. Service call messages are only displayed in English. You cannot select this feature using commands from the host computer. You must select the language from the control panel. You can then save the setting in NVRAM (see Section 4.
4.5 Test Menu The Test menu is used to print the printer configuration sheet and the font status sheets. Table 4–47 describes the features in the Test menu. NOTE The Test menu is not functional when the optional PostScript protocol is active. You must select either the DEC PPL3 or LJ2D protocol to print the configuration sheet or font status sheets.
Figure 4–12 Configuration Sheet DECLASER 3200 Printer Page Count 11595 Page Description Language : PostScript Co-processor : Installed Available Memory : 6494148 bytes Protocol Firmware: V1.0 Engine Firmware: V1.
4.5.2 Printing the Font Status Sheets Selecting FONT STATUS from the Test menu prints the font status sheets which show the available printer fonts. Figure 4–13 shows an example of the DEC PPL3 font status sheet. For additional information about fonts for the DEClaser 3200 printer, see Appendix F. NOTE You must select either the DEC PPL3 or LJ2D protocol to print the font status sheet.
Figure 4–13 Font Status Sheet MLO-006490 Printer Menus 4–59
4.6 Defaults Menu The Defaults menu is used to perform the following functions: • Reset the printer • Recall the default settings programmed at the factory • Recall customized user default settings stored in NVRAM • Save changed settings in NVRAM The features in the Defaults menu relate directly to the types of memory the printer uses to store settings. See Section 4.2 for additional information about printer configuration memory. Table 4–48 describes the Defaults menu features.
5 Print Media This chapter describes the print media that are appropriate for use with the DEClaser 3200 printer. The types of print media described in this chapter are paper, labels, transparencies, and envelopes. The DEClaser 3200 printer produces excellent print quality using electrophotographic laser technology. The laser printing process differs greatly from that of a conventional impact printer, so paper selection is particularly important.
5.1 Paper Specifications This section contains information on the sizes and specifications of plain paper that can be used with the DEClaser 3200 printer. Single-size cassettes come in A4, Letter, or Legal sizes. The DEClaser 3200 printer can also use an optional adjustable size cassette that can be configured to accept various paper sizes. For information about the paper sizes that the adjustable paper cassette can accommodate, see Section 4.4.6.
5.1.1 Special Considerations When Printing on Paper Because of the way laser printers bond toner to the paper, you must observe some special requirements with certain types of papers: • The ink from some preprinted papers, such as those with a company letterhead, can cause smearing and, in some cases, could damage the printer. Do not use paper printed with Thermographics letterheads. • Do not use colored papers where the color is applied as a coating to the surface. • Do not use thermal papers.
5.2 Envelope Specifications The DEClaser 3200 printer accepts the following sizes of envelopes for use with the manual feed tray: • #10 Business (4.125 in. x 9.5 in.) • Business (9 in. x 12 in.) • Business (10 in. x 13 in.) • C4 (229 mm x 324 mm) • C5 (162 mm x 229 mm) • DL or C5/6 (110 mm x 220 mm) Envelopes must meet the same specifications as paper (see Table 5–1).
Figure 5–1 Unacceptable Envelopes Open sealing flap Sealing flaps at leading and trailing edges Three or more layers at the leading and trailing edges Transparent windows Clasps, snaps, or strings MLO-006470 Print Media 5–5
5.2.1 Special Considerations When Printing on Envelopes Observe the following requirements when printing on envelopes: • Feed envelopes from the manual feed tray one at a time (see Section 2.7.3). • Print envelopes only on the front side.
5.3 Transparency Specifications Table 5–2 and Table 5–3 contain information on the sizes and specifications of transparencies that can be used with the DEClaser 3200 printer. Table 5–2 Transparency Sizes Transparency Size Dimensions A4 210 mm x 297 mm Letter 8.5 in. x 11 in. Table 5–3 Transparency Specifications Category Specification Transparency weight 142 Thickness 0.105 Material Polyester (coated) Curl 5.0 mm maximum Cutting accuracy 4 g/m2 basis weight 0.005 mm 0.
5.4 Label Specifications A self-adhesive label consists of a face sheet with an adhesive backing layer, and a carrier sheet. The carrier sheet and adhesive used for the labels must be able to meet the heat tolerance specification of 195°C (385°F) for at least 0.1 second. CAUTION Exposed adhesive on labels can cause damage to the printer. To test for adhesive that may be exposed, press a plain piece of paper on top of the sheet of labels. If the paper sticks to the labels, do not use those labels.
5.5 Paper Handling and Storage Although you may be using paper that meets all specifications, improper handling and storage may affect the quality of the paper and the performance of the printer. This can cause paper jams, misfeeding, and other printer performance problems. Follow the recommendations in this section on paper storage and handling to reduce the possibility of printer jams and misfeeds. 5.5.
6 Troubleshooting This chapter contains troubleshooting information for the DEClaser 3200 printer. It is divided into the following sections: • Common operating problems • Communication errors • Error messages • Paper jams 6.1 Common Operating Problems Table 6–1 lists common operating problems and their possible solutions. All corrective actions should be followed in the order in which they are listed.
Table 6–1 Common Operating Problems Problem Possible Cause Corrective Action The power source is defective. Make sure the power cord is plugged into the wall outlet. Check that there is power at the wall outlet by plugging in a lamp to see if it lights. If the lamp does not light, call your building maintenance services to check the circuit supplying power to that outlet. The power cord is not connected or is damaged.
Table 6–1 (Cont.) Common Operating Problems Problem Possible Cause Corrective Action The communications interface selections (baud rate, parity, and so on), do not match the host settings. See Section 4.4.8 for information about these features. The interface cable is not connected properly. Check the cable connections at the printer and at the host computer. Software or command problem. Try printing the Configuration Sheet (Section 4.5).
Table 6–1 (Cont.) Common Operating Problems Problem Possible Cause Corrective Action Toner is not being dispersed evenly. Remove the developer cartridge (with the toner cartridge still installed) and gently rock the cartridge 3 or 4 times to distribute the toner evenly within the cartridge. Poor Printing Vertical/horizontal deletions or spots on the page. NOTE: You may want to do this over a piece of newspaper in case any residual toner falls from the cartridge.
Table 6–1 (Cont.) Common Operating Problems Problem Possible Cause Corrective Action The page printed black. Faulty power supply or board. Call for service (Chapter 8). The page printed blank. The developer cartridge not installed properly. Remove and reinstall the developer cartridge. Faulty developer cartridge. Replace the developer cartridge. The toner cartridge has run out of toner. Replace the toner cartridge. The transfer/separation charger is dirty.
Table 6–1 (Cont.) Common Operating Problems Problem Possible Cause Corrective Action Paper does not meet specifications. See Chapter 5 for print media specifications. Paper is damp. Reload with dry paper. Transfer/separation charger is not seated properly. Remove and reseat transfer/separation charger. There is an obstruction in the paper path. See Section 6.5 for instructions on clearing paper jams. The fusing unit gate is not closed.
Table 6–1 (Cont.) Common Operating Problems Problem Possible Cause Corrective Action Print lines overlap. The vertical pitch setting is incorrect. Correct the vertical pitch setting in your application program. Page breaks occur. Insufficient memory for complex pages. Install additional memory. See Section 4.2.4 for additional information about system memory. Printer is missing fonts. Insufficient memory to load all fonts. Install additional memory. See Section 4.2.
6.2 Communication Errors Communication errors result from the failure of the host computer to communicate properly with the printer. These errors can be caused by a faulty interface cable, or interruption in data flow. Use the following procedure when you encounter a communication error. 1. Make sure the printer is on line. Printer status reads READY. 2. Be sure the printer is configured correctly for your computer.
6.3 Error, Supplies, and Service Messages The DEClaser 3200 printer displays a message and an error code when the printer encounters a problem. Most error messages are self explanatory (for example, CLOSE TOP COVER), but in some cases you may need additional information. Table 6–2 lists error messages numerically by error code. The table details the message, its meaning, and the corrective action to be taken. NOTE To clear some paper jams, you may be required to access more than one area of the printer.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action CALL SERVICE 0305 Communications (ESS) board connection failure Turn the printer off, and then turn it back on after 5 seconds. If this does not clear the error, call for service and report the error code. CALL SERVICE 0312 NVRAM read/write failure Turn the printer off, and then turn it back on after 5 seconds. If this does not clear the error, call for service and report the error code.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action CLEAR PAPER PATH 0820 Manual feed tray registration jam Remove jammed paper from manual feed tray. Open the top cover and remove jammed paper. CLEAR PAPER PATH 0821 Jam in paper tray 1 Remove the upper cassette and remove jammed paper. Open the right side cover and remove jammed paper. CLEAR PAPER PATH 0822 Jam in paper tray 2 Remove the lower cassette and remove jammed paper.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action CLEAR PAPER PATH 0831 Tray 1 trailing-edge jam Open the top cover and remove jammed paper. Remove the upper cassette and remove jammed paper. Open the right side door and remove jammed paper. CLEAR PAPER PATH 0832 Lower cassette trailingedge jam Open the top cover and remove jammed paper. Remove the lower cassette and remove jammed paper. Open the right side door and remove jammed paper.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action REPLACE CARTRIDGE C 0912 Developer cartridge is empty. Replace the developer cartridge. INSTALL CORRECT CARTRIDGE C 0913 Developer cartridge is the wrong type. Install the correct developer cartridge. INSERT CARTRIDGE C 0914 Developer cartridge is missing or faulty. Install (or replace) the developer cartridge. REORDER CARTRIDGE B 0921 Toner cartridge is nearing end of life.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action CLEAR PAPER PATH 1022 Paper from the lower cassette has jammed in the fusing unit. Open the top cover and remove jammed paper. CLEAR PAPER PATH CLEAR PAPER PATH 1023 1024 Paper from the LCIT has jammed in the fusing unit. Paper from the duplex return area has jammed in the fusing unit. Open the left side cover and remove jammed paper. Open the top cover and remove jammed paper.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action COMM ERROR PRESS 1 1405 Received data parity check failed See Section 6.2 for troubleshooting information. If error continues, call service and report the error code. BAD CART 1 PRESS 1500 Unable to verify font cartridge 1 Replace font cartridge 1, or press to ignore the error and proceed. CAUTION: Turn the printer off before replacing the font cartridge.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action BAD MEM BD 4 1502 SIMMs are incorrectly positioned. Reposition SIMMs on the board so that there are no gaps between them. NOTE: Be sure the .5 MB SIMM is in the slot following the last 2 MB SIMM.
Table 6–2 (Cont.) Error, Supplies, and Service Messages Message Code Meaning Corrective Action BAD COMM BD PRESS 1511 Communications board failure (nonfatal) Communications board is faulty but is still functional through the serial or parallel ports. Call service and report the error code. Press printer. to continue using the BAD COMM BD PRESS 1519 Communications board failure (fatal) Call service and report the error code.
6.4 LJ2D Error Messages Certain error messages are displayed only when LJ2D protocol is selected. These messages pertain to tray selection and paper size. When the printer receives a command for a paper size that is not currently loaded in the default paper tray (or in a fail-over tray), one of the messages listed in Table 6–3 is displayed. Table 6–3 lists the error messages and corrective action to take.
Table 6–3 (Cont.) LJ2D Error Messages Message Meaning Corrective Action TRAY 1 or 3 LOAD Paper Size2 Request for a paper size not currently loaded in TRAY 1 or 3. Load the proper size paper in the upper cassette. TRAY 2 or 3 LOAD Paper Size2 TRAY 1, 2, or 3 LOAD Paper Size2 Request for a paper size not currently loaded in TRAY 2 or 3. Request for a paper size not currently loaded in TRAY 1, 2, or 3. If you do not have a cassette with the requested paper size, press to bypass the error.
6.5 Paper Jams The following actions occur when there is a paper jam in the printer: • The printer stops printing and enters the PAUSED state. • The Error indicator lights. • The error message CLEAR PAPER PATH is displayed with a corresponding error code number. • A paper jam indicator lights on the graphic display showing the area of the paper jam. • The alarm sounds (if enabled). Paper jams generate various error codes, depending on which sensors in the paper path detect the jam.
Table 6–2 identifies all paper jams and describes the corrective action to be taken based on the error code number. It is not always necessary to consult Table 6–2 for two reasons: the graphic display indicates where the paper jam occurs, and there are only five components that may need to be opened or removed to access jammed paper (Figure 6–2). NOTE If you have options such as the LCIT or Multi-Media feeder, you may have to remove them in order to clear paper jams in those areas.
6.6 Basic Paper Jam Clearance Procedure Clearing paper jams on the DEClaser 3200 printer is a straightforward task. The following is a basic procedure to clear jammed paper from the printer. If you need more detailed information to clear a paper jam, see Section 6.7. NOTE Whenever you clear a paper jam, you must open and then close at least one cover to clear the error message. 1. Look at the graphic display on the control panel to locate where the paper jam occurred, as indicated by the red LEDs. 2.
6.7 Detailed Paper Jam Clearing Procedure The following paper jam clearance procedure can be used to clear any type of paper jam. Use this procedure if you are unsure of the paper jam location. 1. Open the top cover.
2. Remove any jammed paper inside the printer.
3. Open the left side cover and lift the tab on the fusing unit gate to remove any jammed paper. WARNING The fusing unit may be hot. Use caution when removing paper from this area.
4. Close the fusing unit gate back to its operating position and close the left side cover. CAUTION Be sure the fusing gate is closed before closing the left side cover. Failure to close the fusing gate will result in a paper jam.
5. Close the top cover.
6. Remove the upper and lower cassettes and remove any jammed paper. 26.
7. Insert the upper and lower cassettes. 26.
8. Open the right side cover and remove any jammed paper.
9. Close the right side cover. MLO-006613 10. Press Online/Pause to place the printer back on line (if necessary).
7 Maintenance Most maintenance for the DEClaser 3200 printer is in the form of replacing consumables when they reach their end of life. These consumables consist of the photoreceptor drum, developer, and toner cartridges. When an item needs replacing, the printer displays a message instructing you to replace the particular cartridge. All instructions for replacing consumables come in each cartridge kit. For information about ordering consumables, refer to Appendix G.
7.1 Cleaning the Transfer/Separation Charger Use the following procedure to clean the transfer/separation charger each time the photoreceptor drum is replaced, or when recommended in the troubleshooting section. NOTE This procedure uses the cotton swab and cleaning brush supplied with the photoreceptor drum kit. You may want to clean the charger over a piece of newspaper to catch the residual toner dislodged from the cleaning. 1.
2. Open the top cover by lifting up its release lever.
3. Grasp each (green) end of the transfer/separation charger and lift it out of the printer.
4. Close the top cover by pushing it down until it latches securely in place. NOTE The top cover is closed at this time to prevent light exposure to the photoreceptor drum.
5. Gently clean the corotron wire with the cotton swab until no toner remains on the wire. Clean only the corotron wire, being careful to move around the nylon wires that pass diagonally over it.
6. Hold the charger upright in the vertical position and clean the toner from the sawtooth comb with the cleaning brush.
7. Open the top cover by lifting up its release lever.
8. Install the transfer/separation charger into the printer.
9. Close the top cover by pushing it down until it latches securely in place.
10. Turn the printer on by pressing the power switch on the back of the printer to the | (ON) position.
8 Service If you cannot correct a problem with the DEClaser 3200 printer, request servicing by a qualified Digital Services engineer. This chapter lists the available services. 8.1 Digital Equipment Corporation Services Digital Equipment Corporation provides a wide range of maintenance programs for printers. These include on-site, carry-in, and mail-in maintenance services. You can use these programs to select a plan that meets your service needs, from complete Digital support to self-maintenance.
Refer to the list of questions in Table 8–1 before calling the service center. Table 8–1 Questions to Consider Before You Call Is the call necessary? Check Chapter 6. Often you can solve the problem yourself. Who should call for service? Typically, the system manager should place the call for service. Where should you call? In the continental United States: If you purchased on-site warranty support at the time of sale, call Digital at 1–800–DEC–8000.
A DEC PPL3 Quick Reference Guide This quick reference guide contains basic information about using DEC PPL3 programming instructions with your DEClaser printer. For quick reference, see these sections: Category Location Unit Selection Section A.1 Spacing, Implicit Cursor Motion, Sheet Size and Margins Section A.2 Tabs Section A.3 Explicit Cursor Movement Section A.4 Font Management and Attribute Selection Section A.5 Vectors Section A.6 Reports Section A.7 Device Control Section A.
Conventions The following conventions are used throughout this appendix. Convention Meaning CSI This is the control character (9/11) used to introduce the Control Sequence Introducer as part of the format of a DEC PPL3 command; for example, CSI Pn A. Both parameter characters and intermediate characters are supported in a CSI control sequence. ESC This is the control character (1/11) used to introduce an escape sequence as part of the format of a DEC PPL3 command; for example, ESC 4.
A.1 Unit Selection PUM–Positioning Unit Mode Sets the Positioning Unit Mode CSI 11 h CSI 11 l Resets the Positioning Unit Mode SSU–Select Size Unit CSI Ps SP I Where: Ps = 2 is decipoint 1/720 inch. Ps = 7 is pixel 1/300 inch. Ps = ?1 is centipoint 1/7200 inch. A.
DECSLRM–Set Left and Right Margins CSI Pn1 ; Pn2 s Where: Pn1 = n is the left margin-setting numeric value according to the SSU sequence and PUM setting (Pn1 = 0 is treated as 1). Pn2 = n is the right margin-setting numeric value according to the SSU sequence and PUM setting (Pn2 = 0 is treated as 1).
DECSTBM–Set Top and Bottom Margins CSI Pn1 ; Pn2 r Where: Pn1 = n is the top margin-setting numeric value according to the SSU sequence and PUM setting (Pn1 = 0 is treated as 1). Pn2 = n is the bottom margin-setting numeric value according to the SSU sequence and PUM setting (Pn2 = 0 is treated as 1). DECVPFS–Variable Page Format Select CSI Ps1 ; Pn2 ; ... ; Pn11 SP z Where: Ps1 = 0, 1 is portrait orientation. Ps1 = 2 is landscape orientation. Ps1 = Other is portrait orientation.
PFS–Page Format Select CSI Ps SP J Where: Ps = 0 Portrait normal text Ps = 1 Landscape normal text Ps = 2 Portrait normal A4 Ps = 3 Landscape normal A4 Ps = 4 Portrait normal North American letter Ps = 5 Landscape normal North American letter Ps = 6 Portrait extended A4 Ps = 7 Landscape extended A4 Ps = 8 Portrait extended legal Ps = 9 Landscape extended legal Ps = ?20 Portrait extended North American letter private Ps = ?21 Landscape extended North American letter private Ps = ?22
DECPSP–Proportional Spacing Mode CSI ? 27 h CSI ? 27 l Sets Proportional Spacing Mode Resets Proportional Spacing Mode DECSHORP–Set Horizontal Pitch CSI Ps w Where: Ps = 0 is determined by current font. Ps = 1 is 720 centipoints (10 characters/inch). Ps = 2 is 600 centipoints (12 characters/inch). Ps = 3 is 545 centipoints (13.2 characters/inch). Ps = 4 is 436 centipoints (16.5 characters/inch). Ps = 5 is 1440 centipoints (5 characters/inch). Ps = 6 is 1200 centipoints (6 characters/inch).
DECVERP–Set Vertical Pitch CSI Ps z Where: Ps = 0 is determined by the current font. Ps = 1 is 1200 centipoints (6 lines/inch). Ps = 2 is 900 centipoints (8 lines/inch). Ps = 3 is 600 centipoints (12 lines/inch). Ps = 4 is 3600 centipoints (2 lines/inch). Ps = 5 is 2400 centipoints (3 lines/inch). Ps = 6 is 1800 centipoints (4 lines/inch). Ps = 10 is 1152 centipoints (66 lines/A-size printable area). Ps = 11 is 1152 centipoints (66 lines/A-size printable area).
SHS–Set Horizontal Spacing CSI Ps SP K Where: Ps = 0 is 720 centipoints (10 characters/inch). Ps = 1 is 600 centipoints (12 characters/inch). Ps = 2 is 480 centipoints (15 characters/inch). Ps = 3 is 1200 centipoints (6 characters/inch). SPI–Spacing Pitch Increment CSI Pn1 ; Pn2 SP G Where: Pn1 = 0 Line spacing is determined by the current font. Pn1 = n Line spacing is determined by the numeric value according to the SSU sequence and PUM setting.
A.3 Tabs DECCAHT–Clear All Horizontal Tabs ESC 2 Clears all horizontal tab stops. DECCAVT–Clear All Vertical Tabs ESC 4 Clears all vertical tab stops. DECHTS–Horizontal Tab Set ESC 1 Sets a tab stop at the active horizontal position. DECSHTS–Set Horizontal Tab Stops CSI Pn ;...; Pn u Where: Pn = n is the number of units according to the SSU sequence and PUM setting. DECSVTS–Set Vertical Tab Stops CSI Pn ;...
TBC–Tab Clear CSI Ps ;...; Ps g Where: Ps = 0 is clear one horizontal tab stop at active column. Ps = 1 is clear one vertical tab stop at active line. Ps = 2 is clear all horizontal tab stops. Ps = 3 is clear all horizontal tab stops. Ps = 4 is clear all vertical tab stops. A.4 Explicit Cursor Movement CUU–Cursor Up CSI Pn A Where: Pn = 0 is treated as 1 vertical position up. Pn = n is the numeric value according to the SSU sequence and PUM setting.
HPR–Horizontal Position Relative CSI Pn a Where: Pn = 0 is treated as 1 horizontal position to the right. Pn = n is the numeric value according to the SSU sequence and PUM setting. VPA–Vertical Position Absolute CSI Pn d Where: Pn = 0 is treated as veritcal position 1. Pn = n is the numeric value according to SSU sequence and PUM setting. VPB–Vertical Position Backward CSI Pn k Where: Pn = 0 is treated as 1 vertical position up.
A.5 Font Management and Attribute Selection ASCEF–Announce Subset of Code Extension Facilities ESC SP Fs If the final character is: L is ISO 4873, Level 1. M is ISO 4873, Level 2. N is ISO 4873, Level 3. DECATFF–Assign to Type Family or Font DCS Ps1 ; Ps2 } id_string ST Where: Ps1 = 0 or 1 assigns a font collection plus by a 16-character font identifier to SGR number. Ps1 = 2 assigns type family ID (7 characters) to SGR number. Ps1 = 3 assigns a 16-character font ID to SGR number.
DECAUPSS–Assign User-Preference Supplemental Character Set DCS Ps ! u D...D ST Where: Ps = 0 is a 94-character set. Ps = 1 is a 96-character set. Possible D . . . D values: %5 DEC Supplemental A ISO Latin-1 Supplemental (Ps = 1) I JIS Katakana1 (Ps = 0) "4 DEC Hebrew Supplemental (Ps = 0) H ISO Latin-Hebrew Supplemental (Ps = 1) 1 (Ps = 0) Not resident DECDTFF–Delete Type Family or Font File DCS Ps ~ id_string ST Where: Ps = 0 requires the ID string for a 7-character type family ID.
DECLFF–Load Font File DCS Ps1 ; Ps2 ; Ps3 y font_record, font_record; comment_record ST Where: Ps1 = 0 is Digital font file format. Ps2 = 0 is print the summary sheet. Ps2 = 1 is do not print the summary sheet. Ps2 = 2 is send font error and warning information. Ps2 = 3 is print the summary sheet and sent font error and warning information. Ps3 = 0 is delete all fonts. Ps3 = 1 is replace loaded font files with same ID as loaded font file.
LS3–Locking Shift 3 ESC o G3 becomes the active GL character set. LS3R–Locking Shift 3 Right ESC | G3 becomes the active GR character set. SCS–Select Character Set ESC I* ...In F Where: I* = ( (Left parenthesis)1 designates the character set into G0. 1 I* = ) (Right parenthesis) 1 I* = * (Asterisk) designates the character set into G1. designates the character set into G2. I* = + (Plus sign)1 designates the character set into G3. 2 I* = - (Minus sign) 2 designates the character set into G1.
Table A–2 Character Set Identification Character Set Number of Characters Character Set Identifier British 94 A ASCII 94 B (initial setting for G1 and G0) DEC Dutch 94 4 DEC Finnish 94 5 French 94 R DEC French Canadian 94 9 German 94 K ISO Italian 94 Y Legal 94 %4 JIS Roman 94 J JIS Katakana1 94 I DEC Norwegian/Danish 94 6 ISO Spanish 94 Z DEC Swedish 94 7 DEC Swiss 94 = Norwegian/Danish 94 ‘ DEC Supplemental 94 %5 DEC Technical 94 > DEC Special Graph
DECMM–Memory Management CSI Ps + v Where: Ps = 0, 1 1 Ps = 2 1 Imaging capabilities are not guaranteed. A or A4-size imaging is guaranteed without complexity errors. Ps = 3 Legal-size imaging is guaranteed without complexity errors. Ps = 41 A or A4-size imaging is guaranteed without complexity errors in duplex mode. Ps = 51 Legal-size imaging is guaranteed without complexity errors in duplex mode.
SGR–Select Graphic Rendition CSI Ps ; . . . ; Ps m Where: Ps = 0 Turns off all attributes (standard and private) Ps = 1 Turns on bold Ps = 3 Turns on italics Ps = 4 Turns on underline Ps = 9 Turns on strike-through Ps = 10 . . .
A.6 Vectors DECRVEC–Draw Relative Vector CSI Ps1 ; Pn2 ; Pn3 SP | Where: Ps1 = 0 Draws a horizontal (X) line to the right. Ps1 = 1 Draws a vertical (Y) line down. Ps1 = 2 Draws a horizontal (X) line to the left. Ps1 = 3 Draws a vertical (Y) line up. Pn2 = n is the line length according to the SSU sequence. Pn2 = n is the line width according to the SSU sequence.
A.7 Reports CPR–Cursor Position Report CSI Pn1 ; Pn2 R Where: Pn1 Numeric parameter describing the active vertical position according to the SSU sequence and PUM setting. Pn2 Numeric parameter describing the active horizontal position according to the SSU sequence and PUM setting. DA–Device Attributes CSI c Requests the Primary Device Attributes Report DAR–Response to Device Attributes (DA) Request CSI ? Ps1 ; Ps2 ; ...
DA2R–Device Attributes (Secondary) Report CSI > Ps1 ; Ps2 ; Ps3 ; Ps4 c Where: Ps1 = 53 Identifies the DEClaser 3200 printer. Ps2 = xx xx is the major firmware version number. Ps2 = 10 Minor firmware version 1.0–yy Ps3 = 0 No memory cards are installed. Ps3 = n is the amount of memory (in Mbytes) installed using 2-Mbyte memory cards. Ps4 = n is the sum of the codes of installed protocols. Ps4 = 1 PostScript emulation protocol is present. Ps4 = 8 HP–PCL4 emulation protocol (LJ2D) is present.
DECRFS–Request Font Status CSI Ps " { Where: Ps = 0 Send both reports (same as 1 followed by 2). Ps = 1 Send font status (includes all built-in fonts, downline loaded fonts, and cartridge fonts). Ps = 2 Send status of memory bytes available for downline loaded fonts. DECFSR–Font Status Report If DECRFS is 1 or 0: DCS 1 " { report_string ST If DECRFS is 2 or 0: DCS 2 " { nnn ST Where: nnn indicates the number of bytes available in memory for downline loading.
DSR–Device Status Report CSI Ps n Where: Ps = 0 No errors Ps = 3 Errors DSR–Device Status Request CSI Ps n Where: Ps = 0 or 5 Send an extended status report. Ps = 6 Send a cursor position report. Ps = ?1 Disable all unsolicited status reports. Ps = ?2 Enable brief unsolicited status reports, and send extended status report. Ps = ?3 Enable extended unsolicited status report, and send extended status report.
A.8 Device Control DECSCL–Set Conformance Level CSI Ps " p Where: Ps = 0 is treated as 73. Ps = 71 Reset to DEC PPL1 defaults Ps = 72 Reset to DEC PPL2 defaults Ps = 73 Reset to DEC PPL3 defaults DECSTR–Soft Terminal Reset Resets the printer to initial state values and returns to DEC PPL3 protocol. CSI ! p RIS–Reset to Initial State ESC c Resets the printer to initial state values and returns to DEC PPL3 protocol.
DECFIN–Document Finishing CSI Ps ! } Where: Ps = 0 Uses the default offset position (no offset) for output paper stacking. Ps = 1 Toggles the paper offset to the alternate position. DECNS–New Sheet CSI SP s Executes a conditional Form Feed and insures that printing resumes on a new front face.
DECSITF–Select Input Tray Failover CSI Ps1 ; Ps2 ; . . . Psn SP w Where: Ps1 = 0 Disables all composite input trays Ps1 = 1 Defines composite tray 1 Ps2–Psn = n Designates the tray as a member of the composite tray (tray numbers are the same as in DECASFC sequence) DECSNC–Set Number of Copies CSI Pn & q Where: Pn = 0 is treated as 1 copy. Pn = 1–99 is the number of copies. Pn > 99 is treated as 99 copies. A.
SnC1R–C1 Receive Mode CSI SP 6 CSI SP 7 Interprets C1 codes as C0 codes Interprets C1 codes as C1 codes A–28 DEC PPL3 Quick Reference Guide
B LJ2D Quick Reference Guide This LJ2D Quick Reference Guide contains basic information about using PCL programming instructions with your DEClaser 3200 printer. See these sections for quick reference: Category Section Job Control Commands Section B.1 Page Control Commands Section B.2 Cursor Positioning Commands Section B.3 Font Selection Commands Section B.4 Font Management Commands Section B.5 Soft Font Creation Commands Section B.6 Graphics Commands Section B.7 Macro Commands Section B.
Conventions The following example of a command illustrates the conventions used throughout this appendix. ESC X g # p T[data] Convention Meaning ESC This is the control or escape character (1/11) used to introduce an escape sequence as part of the format of an LJ2D command; for example, ESC & # X. X This is the parameterized character used to indicate that the escape sequence is parameterized. Parameterized characters used range from 2/1 2/15.
B.1 Job Control Commands Printer Reset Prints any remaining data, deletes temporary fonts and macros, and then restores the printer to the initial state (user defaults). ESC E Output Offset Toggles the current paper offset position to the alternate position. ESC & 11 T NOTE: Powering up the printer, or switching protocols, sets the printer to no offset. Number of Copies ESC & # X Where: # is the number of copies from 1 to 99. Simplex/Duplex Print ESC & # S Where: #=0 Selects simplex printing.
Top Offset Registration ESC & # Z Where: # 1 is the number of decipoints1 (1/720 inch) used to move the origin of the logical page along the long edge of the paper. Positive numbers move the origin down the page; negative numbers move it up (valid to 4 places). Duplex Page Side Selection ESC & a # G Where: #=0 Prints on the next side of the sheet. #=1 Prints on the next front side. #=2 Prints on the next back side.
B.2 Page Control Commands Page Size ESC & # A Where: #=1 Executive (7.25 inches x 10.5 inches) #=2 Letter (8.5 inches x 11 inches) #=3 Legal (8.5 inches x 14 inches) # = 26 A4 (210 mm x 297 mm) # = 80 Monarch Envelope (3.875 inches x 7.5 inches) # = 81 Commercial 10 Business Envelope (4.125 inches x 9.
Page Length ESC & # P Where: # is the number of lines assigned to the logical page. Orientation ESC & # O Where: #=0 Portrait page orientation #=1 Landscape page orientation Left Margin ESC & a # L Where: # is the left margin column number (starting with 0). Right Margin ESC & a # M Where: # is the right margin column number. Clear Horizontal Margins Resets left and right margins to their default settings.
Text Length ESC & # F Where: # is the number of lines in the text area. Perforation Region ESC & # L Where: #=0 Allows you to print in the area between the bottom margin and the top margin of the next page. #=1 Attempts to write in this region brings you to the next page. Horizontal Motion Index (HMI) ESC & k # H Where: #= The distance between columns in increments of 1/120 inch (0 . . . 32767).
Line Spacing ESC & # D Where: #=1 1 line/inch #=2 2 lines/inch #=3 3 lines/inch #=4 4 lines/inch #=6 6 lines/inch #=8 8 lines/inch # = 12 12 lines/inch # = 16 16 lines/inch # = 24 24 lines/inch # = 48 48 lines/inch B.3 Cursor Positioning Commands Cursor positioning can be either absolute or relative. Absolute positioning moves the cursor distances referenced from the left and top margins. Relative positioning moves the cursor distances referenced from the current cursor position.
Horizontal Cursor Positioning (in Decipoints) ESC & a # H Where: # 1 is the distance or position in decipoints1 (1/720 inch). Valid to 2 decimal places Horizontal Cursor Positioning (in Dots) ESC * p # X Where: # is the distance or position in dots (1/300 inch). Horizontal Cursor Positioning Control Codes The following control codes are used to horizontally position the cursor. CR1 (carriage return) Moves the cursor to the left margin on the current line.
Vertical Cursor Positioning (in Rows) ESC & a # R Where: # 1 is the distance or position in columns 1 (as determined by the VMI setting). Valid to 4 decimal places Vertical Cursor Positioning (in Decipoints) ESC & a # V Where: # 1 is the distance or position in decipoints1 (1/720 inch). Valid to 2 decimal places Vertical Cursor Positioning (in Dots) ESC * p # Y Where: # is the distance or position in dots (1/300 inch).
Line Termination ESC & k # G Where: #=0 CR #=1 CR #=2 CR #=3 CR CR; LF LF; FF CR-LF; LF CR; LF FF LF; FF CR-LF; FF CR-LF; LF FF CR-FF CR-LF; FF CR-FF Push/Pop Cursor Position ESC & f # S Where: #=0 Push (store the current cursor position) #=1 Pop (recall the last stored cursor position) LJ2D Quick Reference Guide B–11
B.4 Font Selection Commands Symbol Set ESC ( ID ESC ) ID Selects the primary symbol set and symbol set identification number. Selects the secondary symbol set and symbol set identification number.
Spacing ESC ( s # P ESC ) s # P Selects spacing for the primary font. Selects spacing for the secondary font. Where: #=0 is fixed spacing. #=1 is proportional spacing. Pitch ESC ( s # H ESC ) s # H Selects horizontal spacing for the fixed spaced primary font. Selects horizontal spacing for the fixed spaced secondary font. Where: # 1 is the pitch in characters/inch1 Valid to 2 decimal places Height (Point Size) ESC ( s # V ESC ) s # V Selects the font height for the primary font.
Stroke Weight Selects the stroke weight for the primary font. ESC ( s # B ESC ) s # B Selects the stroke weight for the secondary font. Where: #= values from -7 to +7 (see Table B–2 for typical examples). Table B–2 Stroke Weight Examples # = -7 Ultra thin # = -5 Thin # = -3 Light #=0 Medium, or Book # = +3 Bold # = +5 Black # = +7 Ultra black Typeface Selection ESC ( s # T ESC ) s # T Selects the typeface for the primary font. Selects the typeface for the secondary font.
Transparent Print Data ESC & p # X [transparent data] Where: # is the decimal number of characters you want to print in transparent mode. Underline ESC & d @ ESC & d # D Underline is disabled. Underline is enabled.
B.5 Font Management Commands Font ID ESC * c # D Where: # is the font ID number (0 through 32767). Font Control ESC * c # F Where: #=0 Delete all soft fonts. #=1 Delete all temporary soft fonts. #=2 Delete soft font (the font ID number must have been previously specified). #=3 Delete character code (the font ID number and the character code must have been previously specified). #=4 Make soft font temporary (the font ID number must have been previously specified).
B.6 Soft Font Creation Commands Font Descriptor ESC ) s # W [font descriptor data] Downloads the font descriptor to the printer. Where: # identifies the number of bytes in the font descriptor. Character Code ESC * c # E Establishes the decimal character code for the next character downloaded. Where: # is the decimal character code. Character Descriptor/Data ESC ( s # W [character descriptor & data] Downloads the character descriptor and character data.
B.7 Graphics Command Raster Graphics Resolution ESC * t # R Where: # = 75 75 dots-per-inch # = 100 100 dots-per-inch # = 150 150 dots-per-inch # = 300 300 dots-per-inch Raster Graphics Presentation Mode ESC * r # F Where: #=0 Prints image in the orientation of the logical page. #=3 Prints image along the width of the physical page. Start Raster Graphics ESC * r # A Where: #=0 Sets left graphics margin at X-position 0. #=1 Sets left graphics margin at the current X-position.
Set Compression Mode ESC * b # M Where: #=0 Unencoded #=1 Run-length encoding #=2 Tagged image file format (TIFF) rev. 4.0 Transfer Raster Data ESC * b # W [raster data] Transfers a row of raster graphics to the printer. Where: # is the number of bytes in the raster row. End Raster Graphics ESC * r B Indicates the transfer of a raster graphic image has ended. Horizontal Rectangle Size (in Decipoints) ESC * c # H Specifies the rectangular width of the fill area in decipoints.
Vertical Rectangle Size (in Dots) ESC * c # B Specifies the rectangular fill area height in dots. Where: # is the number of dots (1/300 inch). Area Fill ID ESC * c # G Specifies the level of shading or the type of pattern to use when filling a rectangular area. Where: # indicates the level of shading using values from 1 through 100 (100 = a black page). or # indicates the type of fill pattern to use (1 through 6).
B.8 Macro Commands Macro ID # ESC & f # Y Establishes a macro ID number for use in subsequent macro commands. Where: # is the macro ID number (0 through 32767). Macro Control ESC & f # X Used to define, invoke, and delete macros. Where: #=0 Start macro definition (for last ID specified). #=1 Stop macro definition. #=2 Execute macro (for last ID specfied). #=3 Call macro (for last ID specfied). #=4 Enable macro for automatic overlay (for last ID specified). #=5 Disable automatic overlay.
B.9 Troubleshooting Commands End-of-Line Wrap ESC & s # C Where: #=0 Enables end-of-line wrap when text reaches the right margin. #=1 Disables end-of-line wrap when text reaches the right margin (data is truncated). Display Function ESC Y ESC Z Escape sequences and control codes are printed. Escacpe sequences and control codes are executed. B.10 Protocol Switching Commands ROCS–Return from Other Coding System ESC % @ Returns to PPL3 protocol.
C PostScript Operators Table C–1 lists the PostScript operators supported by the DEClaser 3200 printer. These operators are in addition to the set of operators listed in Adobe’s PostScript Language Reference Manual. Table C–1 PostScript Operators on the DEClaser 3200 Printer Operator Explanation 10x14 Imposes a coordinate space suitable for 10 in. x 14 in. media. 10x14tray Selects the manual feed and imposes the 10x14 page type. 3.875x7.5 Imposes a coordinate space for 3.875 in. x 7.5 in. envelopes.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation allowjobreset Returns a value that indicates whether cancellation of a job from the control panel is allowed. asynchcontrolsmode Returns a value that reflects whether Control-C and ControlT are interpreted asynchronously (as received) or as part of the interpreter’s data stream. b4 Imposes a coordinate space suitable for B4 media. b4tray Selects the manual feed or MMF and imposes the b4 page type.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation DECimage Returns the image-printing mode currently in effect. DECimageparams Returns the DECimage parameters currently in effect. defaultDECimage Returns the printer’s default image-printing mode. defaultDECimageparams Returns the printer’s default DECimage parameters. defaultduplexmode Returns the default value of physical duplex mode.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation eexec Reads encrypted data from the source (either file or string) and executes it. envelopetray Selects the manual feed or MMF and installs the coordinate space indicated by defaultenvelopefeedsize. errorinfo After an error, this array contains information about the error. executive Puts a serial PostScript printer into interactive mode. Do not use this operator in a PostScript program.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation legaltray Selects a tray that contains legal-size media and installs the legal page type. letter Imposes a coordinate space suitable for 8.5 in. x 11 in. media. lettersmall Imposes a letter-size coordinate space with reduced imageable area. lettertray Selects a tray that contains letter-size media and installs the letter page type.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation product Returns the name of the product: ‘‘DEClaser 3250’’. quit Executes a stop when executed from userdict. Exits and restarts the interpreter when executed from systemdict in privileged mode. ramsize Returns the number of bytes of RAM in the printer. realtime Returns the value of a clock that counts in realtime. The resolution of the clock is in 10 millisecond increments.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation setdefaultmansize† Specifies the default page size and orientation for manual feed operation. setdefaultoutputpositioning† Sets the state of defaultoutputpositioning. setdefaultpagetimeout† Sets the default timeout limit for pages. setdefaultpapertray† Sets the slot to be used as the default input tray. setdefaulttimeouts† Sets the values for the default page, job, manual feed, and wait timeouts.
Table C–1 (Cont.) PostScript Operators on the DEClaser 3200 Printer Operator Explanation setsccbatch† Accepts arguments as if to change serial communications settings, but no changes are made. setsoftwareiomode Changes from the PostScript interpreter to the specified mode at the end of the current job. A value of 0 specifies PostScript protocol; 10 specifies DEC PPL3 protocol. settrayswitchpath Changes the search list for input tray failover. settumble Sets tumble mode for the current job.
D VMS Device Control Library Example The DEClaser 3200 printer provides several useful paper handling options, such as duplex printing, multiple input trays, and selecting manual feed. All of these features can be controlled from the host system. This appendix gives an example procedure for creating and installing a device control library that provides the user with access to these features from the VMS operating system.
In the second column of Table D–1, you will see the symbols and . Instead of typing the individual characters < F F > or < E S C >, you must insert the Form Feed (coded as 00/12) or Escape (coded as 01/11) control character into the file, using the special character insert facility provided by your text editor. Where you see the symbol , type a space character. Table D–1 Filenames and Contents for Example SETUP Modules Filename DEC PPL3 Commands TRAY1.
Table D–1 (Cont.) Filenames and Contents for Example SETUP Modules Filename DEC PPL3 Commands LPR66.TXT [ L[?52h[11h [181;5940s[2g [757;1333;1909;2485;3061;3637;4213;4789;5365; 5941u[1;7920r[11l You have now created 21 text files. The next step is to insert these text files into a device control library. Use the following DCL command to create the library. $ LIBRARY/CREATE/TEXT ANSI_SETUPS.
Once you have installed the device control library, you must now edit the system startup files that involve printer queue initialization. (These are usually found in the SYS$STARTUP directory.) For each printer queue initialization command (INITIALIZE/QUEUE) for which you want to provide this library, add the following /LIBRARY qualifier (or change the existing qualifier) to the following. /LIBRARY=ANSI_SETUPS If you defined a search list, use the following qualifier.
• Using the Set Sheet Size (DECSSS) and Variable Page Format Selection (DECVPFS) commands to support special media sizes for use with the optional Multi-Media Feeder or adjustable paper cassette. • Switching between DEC PPL3 and LJIID emulation protocols with the Select Other Coding System (SOCS) command. To create a module, you edit a text file and type in the necessary DEC PPL3 commands.
• The following command will print several files, each with different attributes. $ PRINT/QUEUE=DEClaser_queue first_file/SETUP=(TRAY1,EXEC),– $_ second_file/SETUP=(TRAY2,LEGAL,DPX),– $_ third_file/SETUP=(TRAY2,LEGAL,SPX) The first file is formatted for Executive-size paper and uses paper tray 1. The second file is formatted for Legal-size paper, and will be printed duplex, using paper tray 2. The third file is also formatted for Legal-size paper, but will be printed simplex from tray 2.
Table D–2 ANSI_SETUPS Example Device Control Library Reference Guide Module Description Tray Selection TRAY1 Print job using media in tray 1. TRAY2 Print job using media in tray 2. TRAY3 Print job using media from the optional Large Capacity Input Tray (tray 3). TRAY4 Print job using media from the optional Multi-Media Feeder. MAN Print job using manually fed media. Duplex Printing SPX Print job simplex (one-sided). DPX Print job duplex (two-sided). DPXT Print job duplex and tumble.
E LN03 Compatibility This appendix contains information highlighting the differences between the DEClaser 3200 printer and the LN03 printer family (LN03 and LN03 Plus). The information emphasizes the differences affecting compatibility between the printers. E.1 General Differences The following list identifies the general differences between the LN03 printer and the DEClaser 3200 printer.
E.2 Printable Area Compatibility The printable area on the DEClaser 3200 printer is approximately the same as the printable area on the LN03 printer. There is a nonprintable area of approximately 6 mm (.25 in.) around the page. This difference does not affect any application using the predefined Page Format Selections (PFS) or applications that do not print within 6 mm (.25 in.) of the paper edge.
• The DEClaser 3200 printer does not contain the Modern Gothic font; the LN03 PLUS does. • If a font used on the page is deleted to free up memory for another requirement, the DEClaser 3200 printer may cause a page break but, unlike the LN03 PLUS, does not try to transfer the display list to bitmap memory. If you encounter page breaks, set the memory management value to FULL (Section 4.4.2.3). NOTE The FULL value can be activated only if at least 2 MB of optional RAM is installed in the printer.
F Fonts for the DEClaser 3200 Printer This appendix describes the contents of the optional DEC PPL3 font cartridges supported by your DEClaser printer. The DEClaser 3200 printer can use the following optional DEC PPL3 font cartridges: Font Name Order Number CG Times LN08X–CA CG Triumvirate LN08X–CB ITC Souvenir and Script LN08X–CC Monospaced LN08X–CD F.1 Font Attributes Each font has attributes that define the appearance of characters. The following table lists examples of these attributes.
F.2 Supported Font Cartridges Table F–1 describes four of the standard DEC PPL3 optional font cartridges available for the DEClaser 3200 printer. The number in the Select Graphic Rendition (SGR) column is used in a control sequence to invoke a particular font or type family. When the type family is invoked, everything you print appears in the characteristics of that family until you change the font cartridge or return the printer to its default state.
Table F–1 Font Cartridge Characteristics Type Family SGR Font Vendor Complement Character Sets LN08X–CA Times Cartridge CG Times 17 Compugraphic 8, 8I, 8B, 10, 10I, 10B, 12, 12I, 12B, 14, 18, 18B, 24 ASCII, ISO Latin-1 Supplemental, DEC Supplemental LN08X–CB Triumvirate Cartridge CG Triumvirate 18 Compugraphic 8, 8I, 8B, 10, 10I, 10B, 12, 12I, 12B, 14, 18, 18B, 24 ASCII, ISO Latin-1 Supplemental, DEC Supplemental LN08X–CC Souvenir and Script Cartridge ITC Souvenir 17 Compugraphic 8, 8I, 8B
F.3 Selecting Fonts This section describes how to select fonts using the WPS–PLUS and DECmate/WPS systems, as well as a summary of programming information to use on various operating systems. F.3.1 WPS–PLUS You must use an appropriate keyword when using fonts with WPS–PLUS. • For WPS–PLUS/VMS (V3.0, V3.1) or ALL–IN–1 (V2.3, V2.4) applications: the Guide to Modifying Printer Tables contains detailed instructions for using keywords. • For WPS–PLUS/VMS (V4.
F.3.2 DECmate/WPS For complete information on DECmate/WPS, refer to DECmate, Using the LN03. When using a font cartridge on a DECmate/WPS system, enter a printer font control block.
Table F–2 Printer Font Control Block for Proportional Fonts Type Family FN SZ HW VS CG Times 8 80 20 40 8 100 24 48 8 120 28 56 8 140 30 64 8 180 39 80 8 180 38 801 8 240 53 104 9 80 20 40 9 100 24 48 9 120 28 56 9 140 33 64 9 180 42 80 9 180 43 801 9 240 53 104 8 80 19 64 8 100 23 80 8 120 27 80 8 140 30 64 CG Triumvirate ITC Souvenir English Embassy : 140 30 64 : 180 39 80 OCR–A N/A 100 30 48 OCR–B N/A 100 30
Table F–2 (Cont.) Printer Font Control Block for Proportional Fonts Type Family 1 FN SZ HW VS 9 180 42 80 9 180 43 801 9 240 53 104 Because only the HW value is different from the previous style, this style is printed in bold. F.4 Summary of Programming Information You can use the following examples directly or with systems other than the ones mentioned in this chapter. Use the following procedure to select fonts: 1.
Examples of Choosing Fonts To select CG Times 10-point font, use the following command: [17m[?27h[100;100B To select the CG Triumvirate 12-point italic font, use the following command: [18m[?27h[120;120B[3m To select the OCR–A font, you must first assign OCR–A to an otherwise unused SGR number between 10 and 19, using the type family ID.
Table F–3 (Cont.
The barcodes are provided in two heights: an 18-point height and a 36point height. The 18-point height consists of 1/4 inch bars that can be used repetitively to produce a total symbol height. The 36-point height consists of 3/8 inch bars, plus a 10-point human-readable character beneath the bars. The 36-point height provides a complete and simple-to-use font. A ‘‘quiet zone’’ of white space is required both before and after the symbol; the minimum quiet zone is 0.
G Accessories and Supplies This appendix lists the accessories and supplies available for the DEClaser 3200 printer. Table G–1 lists the options currently available for the DEClaser 3200 printer. Contact your Digital sales representative or refer to your latest DECdirect catalog for a complete list of products and pricing information. See Section G.1 for additional ordering information.
Table G–1 (Cont.) Accessories and Supplies Part Number Description Paper Feeders LN08X–TE Multi-Media feeder (MMF) LN08X–TF Large capacity input tray for Letter-size paper LN08X–TG Large capacity input tray for A4-size paper Paper Cassettes LN08X–TD Adjustable-size paper cassette LN08X–TC Letter-size paper cassette LN08X–TB Legal-size paper cassette (8.5 in. x 14 in.
Table G–1 (Cont.) Accessories and Supplies Part Number Description Media LN01X–AB Letter-size paper 8 ½ in. x 11 in. 5000 sheets per box LN01X–AD A4-size paper 297 mm x 210 mm 5000 sheets per box LN01X–AC Legal-size paper 8 ½ in. x 14 in. 5000 sheets per box LN03X–AJ Letter-size transparencies 8 ½ in. x 11 in.
Table G–1 (Cont.
G.1 Ordering Information Use the addresses and telephone numbers in Table G–2 and Table G–3 to order products and documentation for the DEClaser 3200 printer. Table G–2 Ordering Within the U.S.A. MAIL Digital Equipment Corporation PO Box CS2008 Nashua, NH 03061 TELEPHONE Order toll free 1–800–DIGITAL between the hours of 8:30 a.m. and 8:00 p.m. Eastern Standard Time Table G–3 Ordering Outside the U.S.A.
H Specifications This appendix contains the specifications for the DEClaser 3200 printer. H.1 Operating Specifications Table H–1 lists the operating, storage and interface specifications for DEClaser 3200 printer.
Table H–1 (Cont.) DEClaser 3200 Specifications Output Tray Capacity: Up to 500 sheets (job offset facedown stacking) Paper Weight Range Cassette Feed: 60 g/m2 to 80 g/m2 basis weight (16 lb. to 21 lb.) Paper Weight Range Manual Feed: 60 g/m2 to 90 g/m2 basis weight (16 lb. to 24 lb.) DEC PPL3 Font Files: There are 20 built-in DEC PPL3 font files. The font files consist of 4 fonts and 5 character sets. These fonts are: • Courier 10 point, 10 pitch normal1 portrait • Courier 10 point, 10.
Table H–1 (Cont.) DEClaser 3200 Specifications Acoustic Noise: 53 dB(A) maximum during standby 55 maximum during printing Operating Temperature: 10°C to 32°C (50°F to 90°F) Operating Humidity: 20% to 80% relative humidity Storage Temperature: -20°C to 40°C (-4°F to 104°F) Storage Humidity: 10% to 85% relative humidity Line Voltage: 120 Vac, 60 Hz, 12 A max 220–240 Vac, 50 Hz, 7 A max Power Consumption: Running = 0.85 KW Standby = 0.3 KW Installed Weight: Approximately 38 kg (85 lb.
H.2 Serial Interface Signals All interface signals specified in this section conform to EIA Standard RS-423 (EIA Industrial Electronics Bulletin No.12). The printer provides the interface signals shown in Table H–2. Designations of circuit direction are provided to indicate the source of the signals. H.2.1 Connector A Digital standard connector is used to support the serial interface. This connector is a modular 6-pin DECconnect-type connector. Table H–2 describes the serial interface signals.
H.2.1.2 Receive Common This circuit establishes the common ground reference potential for the Receive Data and Request To Send interface circuits. H.2.1.3 Receive Data The printer receives signals on this circuit that represent serially encoded characters being sent to the printer. H.2.1.4 Send Data The printer sends signals on this circuit that represent serially encoded characters being sent from the printer. H.2.1.
H.3 Parallel Interface Requirements The parallel interface is an 8-bit industry-compatible interface. It resides on the printer controller board and contains the functionality described in this section. This interface is capable of supporting data transfer at the rate of at least 25 Kbytes per second. H.3.1 Connector The interface connector is a 36-pin (female) Amphenol-type accessible from the rear of the printer. H.3.2 Interface Signals The printer shall provide the interface signals shown in Table H–3.
Table H–3 (Cont.) Parallel Interface Signals Pin Direction Signal Description 11 From printer BUSY H BUSY "high", indicates the printer cannot receive data (buffer full). BUSY high occurs when the printer is paused, or an error condition exists. 12 From printer PE H PAPER END high signal indicates paper out. 13 From printer SLCT H A high signal indicates the printer is in the select state. A low signal occurs when printer is deselected or if an error condition exists.
I Cabling Information This appendix describes the different cable combinations to use for connecting your printer to a host device and includes IBM PC interface programming instructions. I.1 Cable Combinations Table I–1, column 1, lists the devices that can connect your printer. They are grouped by the type of connector they use. The second column lists the part numbers of the adapter and the cable required for each device. Determine what device you have and obtain the appropriate adapter.
Table I–1 (Cont.) Cables and Adapters for Communication Connections Connector Type Adapter and Cable Required Connecting Instructions H8571–B and BC16E1 Attach the H8571–B (9-pinto-MMJ) adapter to these devices, then connect one end of the BC16E cable to the H8571–B. Attach the other end of the BC16E cable to the printer. BC16E1 Attach one end of the BC16E cable to one of these devices. Attach the other end of the BC16E cable to the printer.
Table I–1 (Cont.) Cables and Adapters for Communication Connections 9-Pin Plug Devices IBM PC/AT Type H8571–J and BC16E1 Attach the H8571–J adapter to one of these devices, then connect one end of the BC16E cable to the H8571–J. Attach the other end of the BC16E cable to the printer. Use data transmit ready (DTR) flow control (see Section 4.4.9.3).
I.2 Interface Programming Instructions This section describes how to set up an IBM PC to interface with your printer. I.2.1 Serial Flow Control If you are using an IBM PC or compatible and you want to use the optional serial port on your PC, follow these steps: 1. Edit your AUTOEXEC.
If you are using a 25-pin PC/SA with XON/XOFF, follow these steps: 1. Edit your AUTOEXEC.BAT file to contain the following two lines: mode com1:9600,n,8,1,-,B mode lpt1:=com1: where: mode com1:9600,n,8,1,-,n Specifies that the first serial port (COM1) is used by the printer, that 9600 baud is the communication speed, that no parity is selected, that 8 data bits are selected, that 1 stop bit is used, that the host tries only once to connect, then time-out, and that the type weight is normal.
Glossary ASCII American Standard Code for Information Interchange. The ASCII code table is widely used for data processing and communication. The codes listed represent a set of characters and commands. A4-size The European paper size of 210 mm x 297 mm. basis weight A measurement that describes the paper weight density in grams per square meter. Acceptable basis weight ranges for the DEClaser 3200 printer are from 60 g/m2 to 90 g/m2 , or the equivalent of 16 lb. to 24 lb.
built-in fonts Fonts that reside in memory and are shipped with the printer. These fonts are sometimes referred to as internal, or resident fonts. character attribute A feature of a highlighted character. You can select underlining, bold printing, italic printing, and strike-through attributes. character set A set of codes that correspond to a set of characters. For example, a character set might contain the code for an uppercase A or the number 1.
DTR Data Terminal Ready. A control signal used with RS423 serial communication. DTR regulates the flow of data to the input buffer of the printer by placing a high or low voltage on the DTR line of the serial port. DTR is sometimes known as ‘‘hardware handshaking protocol.’’ duplex A page layout indicating that a document is to be printed on two sides. factory defaults Values or settings that have been programmed at the factory.
font ID (DEC PPL3) A 16-character code that describes the seven basic font attributes (including type family) of the ROM fonts. The code cannot contain lowercase letters. font # (LJ2D) A number used to identify which font the printer uses. fusing unit The fusing unit contains heat and pressure rollers that bond the toner to the paper. host A computer that provides services and enables startup and management of peripheral devices, such as printers. image area The printable portion of a page.
Legal-size The North American paper size of 8 ½ in. x 14 in. Letter-size The North American paper size of 8 ½ in. x 11 in. line weight The thickness of a line. The thicker the line, the heavier the line weight. menu Menus contain the features and values to configure the printer or selections to print status sheets or to save values. For example, the Set Up menu contains features such as PROTOCOL and COMM INTERFCE to select which protocol and type of interface you want to use.
parallel interface A data communications interface that transmits multiple bits of data (usually in 1-byte segments) simultaneously. The DEClaser 3200 printer uses a Centronics parallel interface. pause A paused state of operation during which the printer cannot print data received from the host computer. When the Online indicator is off, it indicates that the printer is paused. portrait printing A method of printing characters parallel to the short edge of the paper.
protocol A procedure or set of rules that controls the communication between computers and peripherals. Also, a set of conventions between communicating processes regarding the format and contents of messages to be exchanged. RAM Random-access memory. RAM retains data only while power remains on. Data is cleared from RAM when the printer is powered off. The DEClaser 3200 printer contains 0.5 MB of built-in RAM which is expandable to 10.5 MB with optional memory boards (SIMMs).
type family A group of fonts that have a similar design, but differ in the six other font attributes. For example, Courier is the type family that resides in the DEClaser 3200 printer. type family ID (DEC PPL3) A 7-character code that identifies a type family font attribute. user defaults Values or settings that have been saved in NVRAM by the user. The printer loads the user default selections into the operating memory each time the printer is powered on.
Index A Aborting a print job, 4–48 Accessories and supplies, G–1 Adjustable cassette feature, 4–49 Adjustable paper cassettes, 2–15 Alarm feature, 4–50 Allow job reset feature, 4–48 Associated documents, xviii Asynchronous control mode feature, 4–49 Auto wrap feature, 4–24 B Barcode 3 of 9, F–9 extended codes, F–10 symbol encoding, F–10 Baud rate feature, 4–52 C Cabling information, I–1 combinations, I–1 Cassettes adjustable, 2–15 loading, 2–7 Cleaning transfer/separtion charger, 7–2 Clearing paper jams,
Error indicator, 3–5 Error messages, 6–9 LJ2D, 6–18 F Factory defaults, 4–60 Factory defaults memory, 4–7 Features Adjustable paper cassette, 4–49 Alarm, 4–50 Allow job reset, 4–48 Asynchronous control mode, 4–49 Auto wrap, 4–24 Baud rate, 4–52 Communications error, 4–55 Communications interface, 4–51 Control representation mode, 4–27 Copies, 4–29 Device ID, 4–26 Display language, 4–55 Duplex (DEC PPL3), 4–17 Duplex (LJ2D), 4–31 Duplex (PostScript), 4–39 Flow control, 4–54 Font number, 4–31 Form length, 4–
L Labels special considerations, 5–8 specifications, 5–8 Laser safety, xx Last Page indicator, 3–4 LEDs, 3–2 LJ2D conventions, B–2 LJ2D Menu, 4–27 LJ2D Quick Reference Guide, B–1 cursor positioning commands, B–8 font management commands, B–16 font selection commands, B–12 graphics commands, B–18 job control commands, B–3 macro commands, B–21 page control commands, B–5 protocol switching commands, B–22 soft font creation commands, B–17 troubleshooting commands, B–22 LN03 compatibility, E–1 Logical duplex, 4–
Paper (Cont.
Tray selection feature (DEC PPL3), 4–16 Tray selection feature (LJ2D), 4–29 Tray switching feature, 4–41 Tray switch sequence feature, 4–41 Troubleshooting, 6–1 Tumble feature (PostScript), 4–39 Tumbling, 4–18 U User defaults, 4–60 User defaults memory, 4–7 User preference set feature, 4–25 V Virtual memory, 4–36 W Wait timeout feature, 4–44 X XON/XOFF flow control, 4–54 Index–5
