Programming instructions

XR100 Series Programming Guide Digital Monitoring Products
33
Output OptiOns
Output Options
11.1
OUTPUT OPTIONS
Output Options
This section allows you to program panel output options. The panel provides
twoFormCrelays(1and2)andfourswitchedground(opencollector)outputs
numbered3to6.UsetheJ22LX-Busonthepanelandmultiple716Output
ExpanderModulestosupportupto100additionalrelayoutputs.Alternately,when
using the 1100X wireless receiver, 45 wireless outputs are available. Refer to the
XR100SeriesInstallationGuide(LT-0899)forcompleteinformation.
Select from the following output numbers:
•1to6
•450to474—Slowresponsetime*wirelessoutputs(activateswithin15seconds)
•480to499—Fastresponsetime*wirelessoutputs(activateswithin1second)
•500to599—LX-Busoutput
•D1toD8—Keypaddoorstrikerelayforaddresses1-8
•G1toG20—Outputgroup
* The response time of a wireless output is the time it takes for a wireless output
to activate once the panel event occurs. You determine whether a wireless output
is a slow or fast response based on the output number assigned. A slow response
output number extends battery life, but response time may be up to 15 seconds.
A fast response output number responds within 1 second, but reduces battery life.
Refertothespecicwirelessoutputinstallationguidetodeterminebatterylife.
11.2.1
CO OUTS: - - - - - -
Cutoff Output
Outputs1to6canbeenteredheretoturnoffafteratimespeciedinCUTOFF
TIME.Todisablethisoption,pressanySelectkeytoclearthedisplaythenpress
COMMAND. The Cutoff Output displays dashes when no outputs are selected.
11.2.2
CUTOFF TIME: 0
Output Cutoff Time
IfaCutoffOutput(1-6)isassigned,enteraCutoffTimeof1to99minutesforthe
outputtoremainon.Enter0(zero)forcontinuousoutput.
11.3
COMM TRBL OUT: 0
Communication Trouble Output
EntertheoutputnumbertoturnonwhenaDDsystemfailstocommunicateon
three successive dial attempts or if the backup communication line transmits a
report.TheCommunicationTroubleOutputalsoturnsonwhenNETisselected
astheprimarycommunicationmethodandNETcommunicationfailsafterone
minute.WhenNETcommunicationisrestoredtheCommunicationTroubleOutput
automatically turns off.
To manually turn the output off, disarm any area or select Off for the output
numberintheUserMenuOutputsOn/Offsection.Enter0(zero)todisablethis
output.
11.4
FIRE ALR OUT: 0
Fire Alarm Output
Entertheoutputnumbertoturnonwhenaretypezoneisplacedinalarm.The
outputisturnedoffusingtheSensorResetoptionwhilenoadditionalretype
zonesareinalarm.Enter0(zero)todisable.Thisoutputisnotcompatiblewith
Cutoff Outputs.
11.5
FIRE TRB OUT: 0
Fire Trouble Output
Entertheoutputnumbertoturnonwhenaretypezoneisplacedintrouble,
when a supervisory type zone is placed in trouble, or when any system monitor
(AC,Battery,PhoneLine1orPhoneLine2)isplacedintrouble.Theoutputturns
offwhenallreandsupervisorytypezones,orsystemmonitorsarerestoredto
normal.Enter0(zero)todisablethisoutput.Thisoutputisnotcompatiblewith
CutoffOutputs.Thisoutputcanbeconnectedtoalamp,LED,orbuzzerusingthe
DMPModel716OutputExpansionModule.