User's Manual
Table Of Contents
- Description
- Installing the Keypad
- Removing the Base
- Harness Wiring
- Additional Power Supply
- Wiring a 12 VDC Access Control Reader on 7075 keypads
- 7075 Door Strike Relay Specifications
- 7075 Zone 2 Door Contact with Soft-Shunt™
- 7075 Zone 3 Request to Exit
- Panic Key Options
- Internal Speaker Operation
- Keyboard and Logo Backlighting
- End-User Options
- Entering Alpha Characters
- Entering Non-Alphanumeric Characters
- Installer Options Menu
- Additional Programming for 7064 and 7075 Thinline Keypads
- User’s Guide
- Compatibility
- FCC Information
- Specifications
- Accessories
- Listings and Approvals
Digital Monitoring Products 7000 Series Keypad Installation Sheet
6
7000 Series Keypad Installation Sheet Digital Monitoring Products
7
ACTIVATE ZONE 3
EXIT: NO YES
Zone 3 Exit (7075 only)
Select YES to enable the Request to Exit feature on zone 3. This zone provides the
ability to cause a door strike to open the door. No panel programming is required.
4 DIGIT ENTRY
CARDS: NO YES
Entry Cards (7064 and 7075 only)
Select YES to enable the 4-Digit Entry Cards function on Home/Away or other systems
that require 4-digit user codes. Home/Away operation is available on the XRSuper6,
XR20, XR40, and XR200 Command Processor™ panels.
ALL?: NO YES
DELAY: 2
Arming/Disarming Wait Time (7064 and 7075 only)
Select the number of seconds the keypad should wait when an area system displays
ALL? NO YES during arming/disarming or a HOME/SLEEP/AWAY system waits during
arming only. If No or YES, or HOME, SLEEP, or AWAY is not pressed before the delay
expires, the keypad automatically selects the YES or the AWAY key. Select zero (0) to
disable this feature. The delay can be one to nine (1-9) seconds. The delay also occurs
when a Wiegand card is presented for arming the Home/Sleep/Away system. After a
card is presented, HOME SLEEP AWAY displays. The keypad waits the programmed
number of seconds before automatically sending AWAY to the panel.
Accessing Keypad Diagnostics
If necessary, refer to Access the User Menu on the previous page.
KPD KPD
OPT DIAG STOP
Keypad Diagnostics (KPD DIAG)
The Keypad Diagnostic option allows you to check the display segments, check the
keyboard backlighting, and test individual keys.
Press the Select key under KPD DIAG. The keypad lights all display segments and
illuminates the keyboard in green. A few seconds later the keypad turns the display off
and illuminates the keyboard in red. The keypad then alternates between these two
states for approximately two minutes. Press COMMAND at any time to continue.
PRESS KEY TO
TEST
Test Individual Keys
The display changes to PRESS KEY TO TEST. This option allows you to test each key on
the keyboard to ensure it is operating properly. Press and hold each key for about two
seconds. The key number being held appears in the display. Verify the correct number
displays before testing the next key.
Z1 OPEN Z2 OPEN
Z3 OPEN Z4 OPEN
Zone Test (7070 and 7075 only)
This option allows the keypads to display the current electrical status of the four
protection zones. The status is shown as OPEN, SHRT, or OKAY.
Note: The Zone information displays on 7064 and 7060 keypads, but is not operational.
INPUT WIEGAND
Input Wiegand (7064 and 7075 only)
This option tests the reader input from DMP 1400 Series proximity credentials. The
display shows OKAY each time a good proximity read is received.
Exiting the Installer Options
When done, press the CMD key once to return to the Installer Options screen. Press the Select key under STOP to
exit the Installer Options function.