Installation Guide

ManualsBrandsDigital Monitoring Products ManualsElectronicsLife Safety and security wireless receiver.

1100XH SERIES HIGH POWER

WIRELESS RECEIVER

Installation Guide

MOUNT THE 1100XH

1. Remove the cover from the plastic housing.

2. Use the included #6 screws to secure the 1100XH to the

wall. See Figure 2 for mounting hole locations.

3. Use one of the provided screws to anchor the housing

in the wall tamper screw hole. See Figure 2 for tamper

location.

PROGRAM THE PANEL

RF RX

RF TX

PANEL RX

PANEL TX

WALL

TAMPER

ENABLE

DISABLE

STATUS

PWR

Figure 1: 1100XH

High Power Wireless

Receiver

Refer to the panel programming guide as needed.

1. Reset the panel.

2. At a keypad, enter 6653 (PROG) to access the

PROGRAMMER menu.

3. In SYSTEM OPTIONS, program a HOUSE CODE between

1 and 50. See House Code Explained for more information.

4. (1100XHE only) At the 1100 ENCRYPTION prompt, select

ALL to only add encrypted wireless devices to the system.

Select BOTH to allow both encrypted and non-encrypted

wireless devices to be programmed.

5. (1100XHE only) The default passphrase appears at

ENTER PASSPHRASE. Press CMD to keep the default. Press

any select key or area to change the passphrase and enter

an 8-character hexadecimal string (0-9, A-F).

6. Press CMD until STOP displays. Press a top row select key

or area to save programming.

DESCRIPTION

The 1100XH Series High Power

Wireless Receiver provides up to

100 wireless zones for XR150 Series

panels and up to 500wireless

zones for XR550Series

panels. The 1100XHE features

128-bitAESencryption.

The 1100XH provides two-way,

supervised communication using

900MHz frequency hopping-

spread-spectrum technology.

The 1100XH contains additional

transmit and receive ampliﬁers to

enable 1100 Series operation at

greater distances or harsh building

environments. The additional gain

introduced by this ampliﬁcation

may inhibit proper communication

with 1100 Series transmitters

located within 4ft of the receiver.

This distance may be 8ft when

using the 1122 PIR or 9000 Series

Wireless Keypads.

The 1100XH is equipped with a case

and wall tamper.

Compatibility

• XR150/XR550 Series Panels

• Encryption requires panel

Version 183 or higher

• 1100T Translator requires

receiver ﬁrmware Version

207/301 or higher

What is Included?

• 1100XH Series High Power

Wireless Receiver

• Model 300 Harness

• Hardware Pack

Tamper Puck

Figure 2: Inside of the 1100XH Housing

Mounting Hole

SELECT A LOCATION

The receiver should be centrally located between the DMP panel

and the 1100 Series transmitters used in the installation based

on the wiring speciﬁcations below. Use an 1106 Series Universal

Wireless Transmitter to perform an LED survey.

1. With the cover removed, hold the transmitter in the desired

location.

2. Press the tamper switch to send data to the panel and

determine if communication is conﬁrmed or faulty.

Conﬁrmed: If communication is conﬁrmed, for each

press or release of the tamper switch, the LED blinks

immediately on and immediately o.

Faulty: If communication is faulty, the LED remains on

for about 8 seconds or ﬂashes multiple times in quick

succession. Relocate the receiver until the LED conﬁrms

clear communication.

Summary of content (4 pages)

PAGE 1
100XH SERIES HIGH POWER WIRELESS RECEIVER Installation Guide WALL TAMPER ENABLE RF RX RF TX DISABLE PANEL RX PANEL TX 1 PROGRAM THE PANEL Refer to the panel programming guide as needed. 1. 2. 3. STATUS PWR 4. Figure 1: 1100XH High Power Wireless Receiver 5. DESCRIPTION The 1100XH Series High Power Wireless Receiver provides up to 100 wireless zones for XR150 Series panels and up to 500 wireless zones for XR550 Series panels. The 1100XHE features 128‑bit AES encryption.
PAGE 2
4 WIRE THE RECEIVER The panel immediately recognizes the 1100XH if the panel is programmed with a house code. Do not use shielded wire between the panel and receiver. 1. 2. 3. Connect the red, yellow, green, and black wires to the PANEL terminal on the 1100XH. Connect the other end of the wires to the XBUS on the panel. See Figure 3. Snap the cover back on to the base.
PAGE 3
1100XH LED Operation The six labeled LEDs on the 1100XH PCB display wireless receiver operation and activity. See Table 2 for LED locations and Table 1 for LED indications. House Code Explained The house code identifies the panel, receiver, and transmitters to each other. The 1100XH automatically sends the specified house code to wireless transmitters when transmitter serial numbers are programmed into the panel.
PAGE 4
LISTED COMPLIANCE SPECIFICATIONS For applications that must conform to a National Recognized Testing Laboratory certified system, read the information below for additional information. Commercial Fire Transmitters must be programmed as supervised. Refer to Table 3 for specific supervision times. The maximum line impedance of the 4-wire bus is 16.2 Ohms for 1, 000 feet (305 meters). The recommended wire gauge for panel to receiver connection is 22 AWG.