User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsLOW POWER TRANSCEIVER

Table Of Contents

Panel Specifications
- 1.1 Power Supply
- 1.2 Communication
- 1.3 Keypads
- 1.4 Number of Zones
- 1.5 Enclosure Specifications
Introduction
- 2.1 System Configurations
- 2.2 Caution Notes
- 2.3 Compliance Instructions
System Components
- 3.1 Accessory Devices
Installation
- 4.1 Mounting the Enclosure
Primary Power Supply
- 5.1 DC Input
Secondary Power Supply
- 6.1 Standby Battery
- 6.2 Replacement
- 6.3 Battery Supervision
LED Operation
- 7.1 Backlit Logo
Reset Button
- 8.1 Description
Programming Connection
- 9.1 Programming Connection
On-Board 1100 Series Wireless
- 10.1 Wireless Antenna
- 10.2 LED Operation
Wireless Keypads
- 11.1 Mounting Keypads
- 11.2 Wireless Keypad Association
- 11.3 Existing Keypad Confirmation
Wireless Zones
- 12.1 Description
Flash Load Button
- 13.1 Description
Listed Compliance Specifications
- 14.1 Introduction
- 14.2 Use Marking
- 14.3 NFPA 72
- 14.4 Types Of Service
- 14.5 Bypass Reports
- 14.6 Battery Standby
Household Burglar-Alarm System UnitsANSI/UL 1023
- 15.1 Bell Cutoff
- 15.2 Entry Delay
- 15.3 Exit Delay
- 15.4 Wireless External Contact
- 15.5 Wireless Supervision Time
- 15.6 Wireless Audible Annunciation
- 15.7 Panel location
- 15.8 Test Frequency
Central Station Burglar Alarm UnitsANSI/UL 1610
- 16.1 Standard Line Security
- 16.2 Remote Disarm
- 16.3 Central Station
Household Fire Warning System ANSI/UL 985 NFPA 72 Specifications
- 17.1 Bell Output Definition
- 17.2 Household System
- 17.3 Wireless External Contact
- 17.4 Wireless Supervision Time
- 17.5 Wireless Fire Verification
- 17.6 Battery Standby
- 17.7 Test Frequency
False Alarm Reduction Programmable Options ANSI/SIA CP-01-2007
- 18.1 Shipping Defaults and Recommended Programming
18.4 Minimum Installation Requirements
18.3 Local Bell
18.2 Entry Delay
Listings and Approvals

Digital Monitoring Products XTL Installation Guide

InstallatIon

Flash Load Button

13.1 Description

TheXTLpanelsoftwarecanbeupdatedviathepanel’sprogramming(PROG)header.Toupdatethepanel

with a new software version, complete the following steps at the protected premise:

1. ConnectaDMP399CablefromtheProgrammingHeadertotheserialportofyourPCoperating

RemoteLinkandcontainingtheXTLRUle.

3. StartRemoteLinkandcreateoropentheXTLcontrolpanelaccountthatmatchesthepaneltobe

updated.

4. SettheConnectionInformationTypetoDirectwithabaudrateof38400andchoosethe

appropriateCOMport.

5. SelectPanel>RemoteUpdate,thenselectthecorrectRUlefortheXTpanelmodel.

6. PressandholdtheLOADbutton(S2),thenpressandreleasetheRESETbutton.

7. ReleasetheLOADbuttonandclick<Update>inRemoteLink.

8. Afterthesoftwareupdateiscompleted,removethe399cableandpresstheRESETbuttonto

resume normal panel operation.