User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsLOW POWER TRANSCEIVER

Table Of Contents

Panel Specifications
- 1.1 Power Supply
- 1.2 Communication
- 1.3 Keypads
- 1.4 Number of Zones
- 1.5 Enclosure Specifications
Introduction
- 2.1 System Configurations
- 2.2 Caution Notes
- 2.3 Compliance Instructions
System Components
- 3.1 Accessory Devices
Installation
- 4.1 Mounting the Enclosure
Primary Power Supply
- 5.1 DC Input
Secondary Power Supply
- 6.1 Standby Battery
- 6.2 Replacement
- 6.3 Battery Supervision
LED Operation
- 7.1 Backlit Logo
Reset Button
- 8.1 Description
Programming Connection
- 9.1 Programming Connection
On-Board 1100 Series Wireless
- 10.1 Wireless Antenna
- 10.2 LED Operation
Wireless Keypads
- 11.1 Mounting Keypads
- 11.2 Wireless Keypad Association
- 11.3 Existing Keypad Confirmation
Wireless Zones
- 12.1 Description
Flash Load Button
- 13.1 Description
Listed Compliance Specifications
- 14.1 Introduction
- 14.2 Use Marking
- 14.3 NFPA 72
- 14.4 Types Of Service
- 14.5 Bypass Reports
- 14.6 Battery Standby
Household Burglar-Alarm System UnitsANSI/UL 1023
- 15.1 Bell Cutoff
- 15.2 Entry Delay
- 15.3 Exit Delay
- 15.4 Wireless External Contact
- 15.5 Wireless Supervision Time
- 15.6 Wireless Audible Annunciation
- 15.7 Panel location
- 15.8 Test Frequency
Central Station Burglar Alarm UnitsANSI/UL 1610
- 16.1 Standard Line Security
- 16.2 Remote Disarm
- 16.3 Central Station
Household Fire Warning System ANSI/UL 985 NFPA 72 Specifications
- 17.1 Bell Output Definition
- 17.2 Household System
- 17.3 Wireless External Contact
- 17.4 Wireless Supervision Time
- 17.5 Wireless Fire Verification
- 17.6 Battery Standby
- 17.7 Test Frequency
False Alarm Reduction Programmable Options ANSI/SIA CP-01-2007
- 18.1 Shipping Defaults and Recommended Programming
18.4 Minimum Installation Requirements
18.3 Local Bell
18.2 Entry Delay
Listings and Approvals

XTL Installation Guide Digital Monitoring Products

InstallatIon

Listed Compliance Specications

14.1 Introduction

Theprogrammingandinstallationspecicationscontainedinthissectionmustbecompletedwheninstalling

theXTLinaccordancewithanyoftheANSI/ULburglarystandards.Additionalspecicationsmayberequired

by a particular standard.

14.2 Use Marking

CommercialCentralStation;HouseholdFireandBurglarWarningSystemControlUnit(Cellular)

14.3 NFPA 72

ThisequipmentshouldbeinstalledinaccordancewithChapter11oftheNationalFireAlarmCode,ANSI/

NFPA72-2002,(NationalFireProtectionAssociation,BatterymarchPark,Quincy,MA02269).Printed

information describing proper installation, operation, testing, maintenance, evacuation planning, and repair

serviceistobeprovidedwiththisequipment.Warning:Owner’sinstructionnotice,nottoberemovedby

anyone except occupant.

14.4 Types Of Service

SuitableforCentralStationStandardLineSecurity.SuitableforHouseholdFireandHouseholdBurglary.Test

weekly.

14.5 Bypass Reports

ThebypassreportsmustbeprogrammedasYESforalllistedburglaryapplications.

14.6 Battery Standby

TheXTLisshippedwithabatteryfor24hourbatterystandbyoperation.

Household Burglar-Alarm System Units

ANSI/UL 1023

15.1 Bell Cutoff

The bell cutoff time cannot be less than four minutes.

15.2 Entry Delay

Themaximumentrydelayusedmustnotbemorethan45seconds.

15.3 Exit Delay

The maximum exit delay used must not be more than 60 seconds.

15.4 Wireless External Contact

Whenused,theExternalContactof1101or1102mustbeprogrammedNormallyClosed.

15.5 Wireless Supervision Time

TheZoneInformationSupervisionTimecannotbesetto0(zero).

15.6 Wireless Audible Annunciation

TheWirelessAudibleoptionmustbeselectedasDAYforresidentialapplications.

15.7 Panel location

Mountpanelinsideprotectedarea.

15.8 Test Frequency

TheTestFrequencyoptionmustbeprogrammedtosendareportatleastonceevery30days.