User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsDigital Transmission System Transceiver

Table Of Contents

Panel Specifications
- 1.1 Power Supply
- 1.2 Communication
- 1.3 Panel Zones
- 1.4 Keypads/Expansion
- 1.5 Number of Zones
- 1.6 Outputs
- 1.7 Enclosure Specifications
Introduction
- 2.1 System Configurations
- 2.2 Caution Notes
- 2.3 Compliance Instructions
System Components
- 3.1 Wiring Diagram
- 3.2 Lightning Protection
- 3.3 Accessory Devices
- 3.4 XT30/XT50 Wiring Diagram
Installation
- 4.1 Mounting the Enclosure
- 4.2 Mounting Keypads
- 4.3 Installation Specifications
Primary Power Supply
- 5.1 AC terminals 1 and 2
- 5.2 Transformer Types
- 5.3 Power LED
Secondary Power Supply
- 6.1 Battery Terminals 3 and 4
- 6.2 Earth Ground
- 6.3 Replacement Period
- 6.4 Discharge/Recharge
- 6.5 Battery Supervision
- 6.6 XT30/XT50 Power Requirements
- 6.7 XT30/XT50 Standby Battery Calculations
Bell Output
- 7.1 Terminals 5 and 6
Keypad Data Bus
- 8.1 Description
- 8.2 Terminal 7 - RED
- 8.3 Terminal 8 - YELLOW
- 8.4 Terminal 9 - GREEN
- 8.5 Terminal 10 - BLACK
- 8.6 Keypad Bus LEDs
- 8.7 Programming Connection
- 8.8 Keypad Addressing
- 8.9 Overcurrent OVC LED
Smoke and Glassbreak Detector Output
- 9.1 Terminal 11
Burglary Zones
- 10.1 Description
- 10.2 Operational Parameters
- 10.3 Zone Response Time
- 10.4 Keyswitch Arming Zone
Powered Zone for 2-Wire Smoke Detectors
- 11.1 Terminals 25 and 26
Annunciator Outputs
- 12.1 Description
- 12.2 Harness Wiring
- 12.3 Model 860 Relay Module
Telephone RJ Connector
- 13.1 Description
- 13.2 FCC Registration
- 13.3 Notification
Ethernet Connector J1
- 14.1 Description
- 14.2 Ethernet LEDs
Reset Header J16
- 15.1 Description
Flash Load Jumper J18
- 16.1 Description
Cellular Connections
- 17.1 Cellular
On-Board 1100 Series Wireless Antenna Connection
- 18.1 Wireless Antenna
- 18.2 LED Operation
Wireless Keypads
- 19.1 Mounting Keypads
- 19.2 Wireless Keypad Association
Listed Compliance Specifications
- 20.1 Introduction
- 20.2 Bypass Reports
- 20.3 Current Draw
- 20.4 Battery Standby
- 20.5 Auxiliary and Bell Current
- 20.6 Cross Zoning
- 20.7 Software Version
- 20.8 App Key
Household Burglar-Alarm System Units ANSI/UL 1023
- 21.1 Bell Cutoff
- 21.2 Entry Delay
- 21.3 Exit Delay
- 21.4 Wireless External Contact
- 21.5 Wireless Supervision Time
- 21.6 Wireless Audible Annunciation
- 21.7 Panel location
- 21.8 Test Frequency
Digital Burglar Alarm Communicator System Units ANSI/UL 1635
- 22.1 Entry Delay
- 22.2 Exit Delay
- 22.3 Test Frequency
- 22.4 Automatic Bell Test
Central Station Burglar Alarm Units ANSI/UL 1610
- 23.1 Central Station
- 23.2 Remote Disarm
- 23.3 Central Station
Household Fire Warning System ANSI/UL 985 NFPA 72 Specifications
- 24.1 Bell Output Definition
- 24.2 Household System
- 24.3 Household Fire Warning
- 24.4 Wireless Supervision Time
- 24.5 Wireless Fire Verification
- 24.6 Battery Standby
- 24.7 Alarm Verification
- 24.8 Model 860
- 24.9 Test Frequency
California State Fire Marshal Specifications
- 25.1 Bell Output Definition
False Alarm Reduction Programmable Options ANSI/SIA CP-01-2010
- 26.1 Shipping Defaults and Recommended Programming
- 26.2 Call Waiting
- 26.3 Entry Delay
- 26.4 Local Bell
- 26.5 Minimum Installation Requirements
Troubleshooting
- 27.1 Troubleshooting Section
- 27.2 Common LCD Keypad Displays
Wiring Diagrams
- 28.1 Multiple Indicating Circuit Modules Installation
- 28.2 System Sensor 2-Wire Smoke Detectors
Revisions to This Document
- Listings and Approvals

Digital Monitoring Products XT30/XT50 Installation Guide

InstallatIon

Reset Header J16

15.1 Description

Theresetheaderislocatedjustabovetheterminalstripontherightsideofthecircuitboardandisused

toresettheXT30/XT50microprocessor.Toresetthepanelwhenrstinstallingthesystem,installthereset

jumperbeforeapplyingpowertothepanel.AfterconnectingtheACandbattery,removetheresetjumper.

To reset the panel while the system is operational, for example, prior to reprogramming, install the reset

jumperwithoutpoweringdownthesystem.Removetheresetjumperafteroneortwoseconds.

Afterresettingthepanel,beginprogrammingwithin30minutes.Ifyouwaitlongerthan30minutes,reset

the panel again.

XT30/XT50 Panel

Phone Line

Outputs

J11

J20

Wireless

Antenna

connection

J7 RJ

Supervision

J24 Celllular

header

Momentarily

place the Reset

jumper over both

of the J16 pins to

reset the panel.

J16

Reset

J18

Load

Ethernet

OVC LED

Power

LED

TX RX

Wireless LEDs

Programming

XMIT

RCV

Figure 8: Panel Showing the Reset Header