User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsDigital Transmission System Transceiver

Table Of Contents

Panel Specifications
- 1.1 Power Supply
- 1.2 Communication
- 1.3 Panel Zones
- 1.4 Keypads/Expansion
- 1.5 Number of Zones
- 1.6 Outputs
- 1.7 Enclosure Specifications
Introduction
- 2.1 System Configurations
- 2.2 Caution Notes
- 2.3 Compliance Instructions
System Components
- 3.1 Wiring Diagram
- 3.2 Lightning Protection
- 3.3 Accessory Devices
- 3.4 XT30/XT50 Wiring Diagram
Installation
- 4.1 Mounting the Enclosure
- 4.2 Mounting Keypads
- 4.3 Installation Specifications
Primary Power Supply
- 5.1 AC terminals 1 and 2
- 5.2 Transformer Types
- 5.3 Power LED
Secondary Power Supply
- 6.1 Battery Terminals 3 and 4
- 6.2 Earth Ground
- 6.3 Replacement Period
- 6.4 Discharge/Recharge
- 6.5 Battery Supervision
- 6.6 XT30/XT50 Power Requirements
- 6.7 XT30/XT50 Standby Battery Calculations
Bell Output
- 7.1 Terminals 5 and 6
Keypad Data Bus
- 8.1 Description
- 8.2 Terminal 7 - RED
- 8.3 Terminal 8 - YELLOW
- 8.4 Terminal 9 - GREEN
- 8.5 Terminal 10 - BLACK
- 8.6 Keypad Bus LEDs
- 8.7 Programming Connection
- 8.8 Keypad Addressing
- 8.9 Overcurrent OVC LED
Smoke and Glassbreak Detector Output
- 9.1 Terminal 11
Burglary Zones
- 10.1 Description
- 10.2 Operational Parameters
- 10.3 Zone Response Time
- 10.4 Keyswitch Arming Zone
Powered Zone for 2-Wire Smoke Detectors
- 11.1 Terminals 25 and 26
Annunciator Outputs
- 12.1 Description
- 12.2 Harness Wiring
- 12.3 Model 860 Relay Module
Telephone RJ Connector
- 13.1 Description
- 13.2 FCC Registration
- 13.3 Notification
Ethernet Connector J1
- 14.1 Description
- 14.2 Ethernet LEDs
Reset Header J16
- 15.1 Description
Flash Load Jumper J18
- 16.1 Description
Cellular Connections
- 17.1 Cellular
On-Board 1100 Series Wireless Antenna Connection
- 18.1 Wireless Antenna
- 18.2 LED Operation
Wireless Keypads
- 19.1 Mounting Keypads
- 19.2 Wireless Keypad Association
Listed Compliance Specifications
- 20.1 Introduction
- 20.2 Bypass Reports
- 20.3 Current Draw
- 20.4 Battery Standby
- 20.5 Auxiliary and Bell Current
- 20.6 Cross Zoning
- 20.7 Software Version
- 20.8 App Key
Household Burglar-Alarm System Units ANSI/UL 1023
- 21.1 Bell Cutoff
- 21.2 Entry Delay
- 21.3 Exit Delay
- 21.4 Wireless External Contact
- 21.5 Wireless Supervision Time
- 21.6 Wireless Audible Annunciation
- 21.7 Panel location
- 21.8 Test Frequency
Digital Burglar Alarm Communicator System Units ANSI/UL 1635
- 22.1 Entry Delay
- 22.2 Exit Delay
- 22.3 Test Frequency
- 22.4 Automatic Bell Test
Central Station Burglar Alarm Units ANSI/UL 1610
- 23.1 Central Station
- 23.2 Remote Disarm
- 23.3 Central Station
Household Fire Warning System ANSI/UL 985 NFPA 72 Specifications
- 24.1 Bell Output Definition
- 24.2 Household System
- 24.3 Household Fire Warning
- 24.4 Wireless Supervision Time
- 24.5 Wireless Fire Verification
- 24.6 Battery Standby
- 24.7 Alarm Verification
- 24.8 Model 860
- 24.9 Test Frequency
California State Fire Marshal Specifications
- 25.1 Bell Output Definition
False Alarm Reduction Programmable Options ANSI/SIA CP-01-2010
- 26.1 Shipping Defaults and Recommended Programming
- 26.2 Call Waiting
- 26.3 Entry Delay
- 26.4 Local Bell
- 26.5 Minimum Installation Requirements
Troubleshooting
- 27.1 Troubleshooting Section
- 27.2 Common LCD Keypad Displays
Wiring Diagrams
- 28.1 Multiple Indicating Circuit Modules Installation
- 28.2 System Sensor 2-Wire Smoke Detectors
Revisions to This Document
- Listings and Approvals

XT30/XT50 Installation Guide Digital Monitoring Products

25