User's Manual

Digital Monitoring Products CellComSL Series Communicator Install/Programming Guide
18
REMOTE OPTIONS
Remote Options
10.1 Remote Options
This section allows you to enter the information needed for Remote Command/Remote
Programmingoperation.AdescriptionoftheRemoteOptionsfollows:
10.2 Remote Key
This option allows you to enter a code of up to eight digits for use in verifying the
authority of a receiver to perform a remote command/programming session. The
receivermustgivethecorrectkeytothe c ommunicator beforebeingallowedaccess.All
CellComSL SeriesCellularAlarmCommunicators are shipped from the factory with the
RemoteKeypresetasblank.
ToenteranewRemoteKey,pressanySelectkeyandenteranycombinationofupto8
digits.Thenumbersyouenterappearasasterisks.PressCOMMAND.
10.3 Remote Disarm
EnterYEStoenablethe c ommunicatortobedisarmedremotely.SelectingNOdisables
remote disarming.
System Reports
11.1 System Reports
This function allows you to select which reports the c ommunicator sends to the receiver.
11.2 Opening/Closing Reports
NO-NoOpening/ClosingReportsaresent.
YES-SendsOpening/ClosingReportsforeachprogrammedarea.
11.3 Zone Restoral Reports
This option allows you to specify whether the communicator sends zone restoral reports
and when they will be sent.
NO-Restoralreportsarenotsentbythecommunicator.
YES-Thecommunicator always sends zone restoral reports at the time the zone
restores from an alarm or trouble condition.
DISARM-Thecommunicator sends zone restoral reports when a zone that has
restored from an alarm or trouble is disarmed. Twenty-four hour zones send restorals
immediately.
System Options
12.1 System Options
This section allows you to select system wide parameters used in the operation of the
c ommunicator system.AdescriptionofeachSystemOptionfollows:
12.2 System
Thisconguresthecommunicator asanAreasystem.
12.3 Entry Delay 1
Entertheentrydelaytimeforallexittypezonesprogrammed.WhenanarmedExit
typezoneisfaulted,thekeypadprewarntonebeginssounding.ENTERCODE:-andthe
nameofthezonecausingtheEntryDelaydisplaysonallkeypads.
Whentherstdigitofacodeisentered,theprewarntonestopsatthekeypad.Ifwithin
veseconds,avalidusercodeisnotenteredoraninvalidusercodeisentered,the
prewarn tone begins sounding again. Fifteen seconds must elapse before entering a digit
silences the prewarn tone again.
The area must be disarmed before the entry delay expires or a fault will be detected.
AllBurglarytypezonesinallareasaredelayedalongwiththeExitzone.
Entrydelaytimescanbefrom30to250seconds.Defaultis30secondsforEntry
Delay1.
12.4 Exit Delay
EntertheExitDelaytimeforallExittypezones.Whentheexitdelaytimestarts,all
activityonexitandburglaryzonesisignoreduntiltheexitdelayexpires.Thekeypad
displaystheExitDelaytimecountdownandannunciatestheExitDelaytoneat8second
intervalsuntilthelast10secondswhenannunciationisat3secondintervals.Theexit
delaycanbefrom45to250seconds.Defaultis60seconds.
REMOTE OPTIONS
RMT KEY:
DISARM NO YES
SYSTEM REPORTS
O/C RPTS YES
RESTORAL YES
NO YES DISARM
SYSTEM OPTIONS
SYSTEM: AREA
ENTRY DLY 1: 30
EXIT DELAY: 60
SYSTEM REPORTS
SYSTEM OPTIONS