User's Manual

CellComSL Series Universal Communicator Installation and Programming Guide Digital Monitoring Products
3
system Components
1.4 Tamper
ThetamperbuttonispressedwhenthecoveroftheCellComSLSeriesCommunicator
issecuredontotheenclosure.Whenthecoverisremoved,thecommunicatorsends
aTamperTroublemessagetotheCentralStation.
1.5 Reset Button
The Reset button is located on the right side of the circuit board and is used to
resetthecommunicatormicroprocessor.Afterresettingthe communicator, begin
programmingwithin30minutes.Ifyouwaitlongerthan30minutes,reset
the communicator again.
1.6 Load Button
The CellComSL SeriesUniversalAlarmCommunicatorrmwarecanbeupdatedvia
theprogramming(PROG)header.Toupdatethecommunicatorwithanewrmware
version, complete the following steps at the protected premise:
399 Programming Cable
1. ConnectaDMP399CablefromtheProgrammingHeadertotheserialportof
yourPCoperatingRemoteLinkandcontainingthecommunicatorRUle.
2. StartRemoteLinkandcreateoropentheaccountthatmatchesthe
communicator to be updated.
3. SettheConnectionInformationTypetoDirectwithabaudrateof38400and
choosetheappropriateCOMport.
4. SelectPanel>RemoteUpdate,thenselectthecorrectRUleforthecommunicator.
5. PressandholdtheLOADbutton,thenpressandreleasetheRESETbutton.
6. ReleasetheLOADbuttonandclick<Update>inRemoteLink.
7. Afterthermwareupdateiscompleted,removethe399cableandpresstheRESETbuttontoresumenormal
operation.
Model 400 USB Flash Module
1. Removetheyellowandgreenwiresfromkeypadbusterminals8and9.
2. PlaceajumperacrosstheReset(J16)header.
3. PlaceajumperacrosstheLoad(J18)header.
4. ConnecttheUSBashdrivetotheModel400andconnecttheassemblytothepanel’sProgramming(J8)
header.TheLEDontheModel400willashandthendisplaysteadygreen.
5. RemovethejumperfromtheReset(J16)header,pressandreleasetheloadbuttonontheModel400to
initiatethermwareupdate.TheLEDonmodel400willashslowly.IftheLEDdisplaysfastashesitmeans
thermwareupdatewasunsuccessful.
6. Theupdatewilltakeapproximately4.5minutesandwhencompletetheLEDontheModel400willdisplay
steady green.
7. ReplacethejumperacrossReset(J16)thenremovetheUSBashdriveandModel400assembly.
8. RemovethejumperfromtheLoad(J18)header.
9. RemovethejumperfromtheReset(J16)header.
10. Reconnecttheyellowandgreenwirestoterminals8and9.
1.7 Backlit Logo
ThebacklitlogoindicatesthePowerandArmedstatusofthecommunicator.Dependingontheoperation,the
LEDdisplaysinRedorGreenaslistedinthetable.TheLEDindicatesthestatusofthesystembatteryand
primary power.
Color and Activity Operation
GreenSteady CommunicatorDisarmed,PrimaryPowerOK,BatteryOK
GreenBlinking CommunicatorDisarmed,PrimaryPowerOK,BatteryFault
NoLight CommunicatorDisarmed,PrimaryPowerFault,BatteryOK
RedSteady CommunicatorArmed,PrimaryPowerOK,BatteryOK
Red/GreenAlternate CommunicatorArmed,PrimaryPowerOK,BatteryFault
RedBlinking CommunicatorArmed,PrimaryPowerFault,BatteryOK
RB
J8
S3
J9
RESET
LOAD
S1
S2
J19
J26
Figure 4: Tamper Location
RB
J8
S3
J9
RESET
LOAD
S1
S2
J19
J26
Figure 5: Reset and Load
Button Location