User's Manual

ManualsBrandsDigital Monitoring Products ManualsElectronicsLow Power Wireless Transceiver

Table Of Contents

Description

InstallatIon GuIde

1137 Emergency Light

Description

The 1137 Emergency Light is a battery powered, wireless LED light

activated by a loss of AC power output from your panel and may be

used as a stair or path light. The 1137 operates using the supplied 3.0

Vdc Lithium batteries.

Compatibility

All DMP 1100 Series Wireless Receivers and Panels

What is Included

The 1137 Emergency Light includes the following:

• One 1137 Emergency Light

• Two 3.0 Vdc Lithium batteries

• Serial number label

Emergency Light Serial Number

For your convenience, an additional pre-printed serial number label

is included. Prior to installing the light, record the serial number or

place the pre-printed serial number label on the 1137 base (see Figure

3). This number is required during programming. As needed, use the

zone name and number label to identify a specic Emergency Light.

Programming the Emergency Light in the Panel

Refer to the panel programming guide as needed. Program the device as an AC Power Trouble Output in ZONE

INFORMATION during panel programming. At the Serial Number prompt, enter the eight-digit serial number. Continue

to program the zone as directed in the panel programming guide.

LED Survey

The 1137 Emergency Light provides a survey capability to allow one person to conrm communication with the

receiver. The 1137 Emergency Light Status LED turns on whenever data is sent to the receiver then immediately

turns off when the receiver acknowledgement is received.

Pressing the button sends data to the receiver to conrm operation. When the Emergency Light does not receive

an acknowledgement from the receiver the LED remains on for approximately eight seconds to indicate that

communication is not established. Communication is also faulty when the LED ashes multiple times in quick

succession. Relocate the light or receiver until the LED immediately turns off indicating the light and receiver are

communicating properly. Proper communication between the light and receiver is veried when for each press of the

button, the LED blinks immediately on and immediately off. Repeat this test to conrm ve separate consecutive

LED blinks. Any indication otherwise means proper communication has not been established.

Figure 1: 1137 Emergency Light

Figure 4: Installing the Top HousingFigure 3: Double-Sided Tape Mount

SERIAL #

Figure 2: Screw Mount

Summary of content (4 pages)

PAGE 1
Installation Guide Description 1137 Emergency Light The 1137 Emergency Light is a battery powered, wireless LED light activated by a loss of AC power output from your panel and may be used as a stair or path light. The 1137 operates using the supplied 3.0 Vdc Lithium batteries. Compatibility All DMP 1100 Series Wireless Receivers and Panels What is Included The 1137 Emergency Light includes the following: • One 1137 Emergency Light • Two 3.
PAGE 2
Mounting the Light These instructions cover installing the 1137 on an interior wall. Figures 2 and 3 show the base housing inside and outside views. Double-sided tape mounting 1. Install a 1/2” wide strip of double-sided tape (not included) in each of the indentations on the back of the base housing. 2. Remove the backing from the tape and place the housing in the desired location on the wall with the cover slot toward the bottom. See Figure 4. Screw mounting 1.
PAGE 3
FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm (7.874 in.) from all persons.
PAGE 4
Patents 800 - 641 - 4282 U. S. Patent No. 7,239,236 Certifications FCC Part 15 Registration ID: CCKPC0155 Industry Canada: 5251A-PC0155 Intrusion • fire • Access • Networks www.dmp.com 2500 North Partnership Boulevard Designed, Engineered and Assembled in U.S.A. S p r i n g fi e l d , M i s s o u r i 6 5 8 0 3 - 8 8 7 7 15065 Battery Life Expectancy 4 years (normal operation) Type 3 Vdc Lithium CR123A See Battery Life Expectancy for full details.