User's Guide
Table Of Contents
- Panel Specifications
- Introduction
- System Components
- Installation
- Primary Power Supply
- Secondary Power Supply
- LED Operation
- RESET Button
- TAMPER Button
- PROG Programming Connection
- On-Board 1100 Series Wireless
- Wireless Zones
- Wireless Key Fobs and Outputs
- Flash LOAD Button
- On-Board Z-Wave Connection
- On-Board Wi-Fi Network
- Cellular Connection
- Wireless Keypads
- Programming Introduction
- Initialization
- Fast Programming
- Communication
- 22.1 Communication
- 22.2 Account Number
- 22.3 Transmission Delay
- 22.4 Communication Type
- 22.5 Backup Cellular
- 22.6 Test Time
- 22.7 Test Days
- 22.8 Check In Minutes
- 22.9 Fail Time
- 22.10 Send Communication Trouble
- 22.11 First Cell APN
- 22.12 Second Cell APN
- 22.13 Receiver 1 Programming
- 22.14 Alarm Reports
- 22.15 Supervisory/Trouble Reports
- 22.16 Opening/Closing and User Reports
- 22.17 Test Report
- 22.18 First IP Address
- 22.19 First IP Port
- 22.20 Second IP Address
- 22.21 Second IP Port
- 22.22 Receiver 2 Programming
- 22.23 Alarm Reports
- 22.24 Supervisory/Trouble Reports
- 22.25 Opening/Closing and User Reports
- 22.26 Test Report
- 22.27 First IP Address
- 22.28 First IP Port
- 22.29 Second IP Address
- 22.30 Second IP Port
- 22.1 Communication
- Network Options
- Messaging Setup
- Device Setup
- Remote Options
- System Reports
- System Options
- 28.1 System Options
- 28.2 System
- 28.3 Closing Code
- 28.4 Closing Check
- 28.5 Entry Delay 1
- 28.6 Exit Delay
- 28.7 Cross Zone Time
- 28.8 Power Fail Delay
- 28.9 Swinger Bypass Trips
- 28.10 Reset Swinger Bypass
- 28.11 Zone Activity Hours
- 28.12 Arm Activity Days
- 28.13 Time Zone Changes
- 28.14 Time Display
- 28.15 House Code
- 28.15.1 Detect Wireless Jamming
- 28.15.2 Wireless Audible Annunciation
- 28.16 Enable Keypad Panic Keys
- 28.17 Occupied Premises
- 28.18 Use False Alarm Question
- 28.19 Weather Zip Code
- 28.1 System Options
- Bell Options
- Output Options
- Output Setup
- Area Information
- Zone Information
- 33.1 Zone Information
- 33.2 Zone Number
- 33.3 Key Fob
- 33.4 Zone Name
- 33.5 Zone Type
- 33.6 Arming Zone Assignment
- 33.7 Area Assignment
- 33.7.1 Style
- 33.8 DMP Wireless
- 33.8.1 Serial Number Entry
- 33.8.2 Contact
- 33.8.3 Supervision Time
- 33.8.4 LED Operation
- 33.8.5 Disarm/Disable
- 33.8.6 Wireless PIR Pulse Count
- 33.8.7 Wireless PIR Sensitivity
- 33.8.8 Next Zone
- 33.9 1144 Series Key Fobs
- 33.9.1 Key Fob User Number
- 33.9.2 Key Fob Serial Number
- 33.9.3 Key Fob Supervision Time
- 33.9.4 Number of Key Fob Buttons
- 33.9.5 Key Fob Button Selection (Four Buttons)
- 33.9.6 Key Fob Button Selection (Two Buttons)
- 33.9.7 Button Action
- 33.9.8 Button Press Time
- 33.9.9 Arm/Disarm Area Selection
- 33.9.10 Output Number
- 33.9.11 Output Action
- 33.10 Alarm Action
- 33.11 Disarmed Open
- 33.11.1 Message To Transmit
- 33.11.2 Output Number
- 33.11.3 Output Action
- 33.12 Swinger Bypass
- 33.13 Prewarn Address
- 33.14 Entry Delay
- 33.15 Cross Zone
- 33.16 Priority
- 33.17 Traffic Count
- 33.18 Zone Audit Days
- 33.19 Receiver Routing
- 33.20 Zone Number
- 33.1 Zone Information
- Stop
- Set Lockout Code
- Appendix
- Listed Compliance Specifications
- Household Burglar-Alarm System Units ANSI/UL 1023
- Central Station Burglar Alarm Units ANSI/UL 1610
- Household Fire Warning System ANSI/UL 985 NFPA 72 Specifications
- False Alarm Reduction Programmable Options ANSI/SIA CP-01-2010
- Revisions to This Document
- Certifications
- Ordering Information
- Accessories
Digital Monitoring Products XTLplus Installation and Programming Guide
14
FAST PROGRAMMING
Fast Programming
21.1 Fast Program
The Fast Program section allows you to quickly congure the essential settings
for the XTLplus panel. When the panel programming defaults are acceptable
for installation and only basic programming options are needed, FAST PROGRAM
allows the installer to quickly enter information without navigating all of the
programming menus. After choosing FAST PROGRAM, continue through the basic list
of options.
21.2 Account Number
Enter the account num ber sent to the receiver. The range of account
numbers are 1 to 65535. For account numbers of four digits or less, you
do not have to enter leading zeros. The panel automatically right justies
the account number. See Communication.
21.3 First IP Address
Enter the rst (primary) IP address and press COMMAND. The panel displays WPS?
NO YES. Press the fourth select key to choose YES. Press the WPS button on the
router. WIFI SETUP SEARCHING displays until connected to the IP address. Advance
to APP Key. See Communication.
21.4 App Key
Enter the 8-digit App Key obtained in your Dealer Settings tab at
dealeradmin.securecomwireless.com. See Remote Options.
21.5 System
This congures the panel as either a six Area system, an All/Perimeter system
(Perimeter/Interior), or a Home/Away system (Perimeter, Interior, and Bedrooms).
See System Options.
21.6 Hours from GMT
Enter the number (0-23) that indicates the Greenwich Time zone (GMT) where the
panel is located. See System Options.
21.7 Weather Zip Code
Enter the zip code of the panel at this option. See System Options.
21.8 Enter Siren Serial Number
Enter the eight-digit serial number for the wireless siren. The siren is automatically
set to Output 61. See Output Setup.
21.9 Zone Number
Enter the zone number to program. See Zone Information.
21.10 Zone Name
Press any select key to display the default zone name. To change the default zone
name, press any select key to clear name. Enter up to 16 characters for the new
zone name.
21.11 Zone Type
To change the default zone type press any select key. See Zone Information.
21.12 Area Assignment
To change the default area, press any select key.
21.13 Serial Number Entry
Enter the eight digit serial number, including leading zeros, found on the
wireless device.
21.14 Stop
When all zones are programmed, press the Back Arrow key to display FAST
PROGRAM. Press COMMAND to display STOP and press any select key to exit the
Fast Program function and save the programming. See Stop.
Note: All programming options are still available by reentering the
programming menu.
FASTPROGRAM
ACCOUNTNO:
FIRST IP ADDR
0.0.0.0
SEARCHING
APPKEY:
SYSTEM:ALL/PERIM
AREA A/P H/A
HRSFROMGMT: 6
ENTER WEATHER
ZIPCODE: 0
ENTER SIREN
SERIAL#:-
ZONENO:-
*DEFAULTNAME*
ZONETYPE:-
AREA:-
SERIAL#:-
STOP
FIRST IP ADDR
WPS? NO YES