PROGRAMMING GUIDE XT SERIES™ PANELS
MODEL XT30/XT50 PROGRAMMING GUIDE When using the XT30/XT50 Series control for any listing organization’s approved methods, refer to this manual and the XT30/XT50 Installation Guide. These documents outline the installation and programming requirements of all applications for which the XT30/XT50 is approved.
TABLE OF CONTENTS Introduction...............................................................1 1.1 1.2 1.3 1.4 1.5 1.6 1.7 1.8 1.9 1.10 Before You Begin.........................................................1 Getting Started............................................................1 Programming Menu.....................................................2 Programmer Lockout Codes..........................................2 Reset Timeout.............................................................
TABLE OF CONTENTS Network Options......................................................11 4.1 4.2 4.3 4.4 4.5 4.6 DHCP Mode Enabled..................................................11 Local IP Address........................................................11 Gateway Address.......................................................11 Subnet Mask.............................................................11 DNS Server...............................................................11 Programming Port............
TABLE OF CONTENTS System Options........................................................18 9.1 9.2 9.3 9.4 9.5 9.6 9.7 9.8 9.9 9.10 9.11 9.12 9.13 9.14 9.15 9.16 9.16.1 9.16.2 9.17 9.18 9.19 9.20 9.21 System Options.........................................................18 System.....................................................................18 Closing Code.............................................................18 Closing Check............................................................
TABLE OF CONTENTS Output Information.................................................26 12.1 12.2 12.3 12.4 12.5 12.6 Output Information....................................................26 Output Number.........................................................26 Output Name............................................................26 Serial Number...........................................................26 Supervision Time.......................................................
TABLE OF CONTENTS 14.19 14.20 14.21 Zone Audit Days........................................................36 Receiver Routing.......................................................37 Zone Number............................................................37 Stop..........................................................................38 15.1 Stop.........................................................................38 Set Lockout Code.....................................................38 16.
INTRODUCTION Introduction 1.1 Before You Begin 1.2 Getting Started Before starting to program, we recommend you read through the contents of this manual. The information in this document allows you to quickly learn the programming options and operational capabilities of the XT30/XT50 panel. After this Introduction, the remaining sections describe the functions of each programming menu items along with their available options.
INTRODUCTION 1.3 Programming Menu You are now ready to start programming the XT30/XT50 panel. Pressing the COMMAND key scrolls you through the programming menu items listed below.
INTRODUCTION 1.6 Keypads DMP offers multiple keypads in a variety of styles that provide programming capabilities. Each keypad and its operation are shown and described in the following sections. Note: Programming cannot be accessed using an Icon Series keypad. Use a 32-character keypad to complete the panel programming.
INTRODUCTION 1.7 Special Keys The following special keys/areas are common to all DMP keypads. COMMAND (CMD) Key Pressing the COMMAND key allows you to go forward through the programming menu and through each step of a programming section. As you go through the programming, the keypad display shows any current programming already stored in the panel memory. If no change is required for an option, press the COMMAND key to advance to the next step.
INTRODUCTION 1.9 1.10 Entering Non-Alpha Characters To enter a space in an alpha entry, press the 9 digit key followed by the third Select key/area. The three characters on the 9 digit key are Y, Z, and space. You can also enter the following characters: – (dash), . (period), * (asterisk), and # (pound sign) using the 0 (zero) key and the four Select keys/areas from left to right. For example, to enter a – (dash), press the 0 (zero) key and then the left Select key/area.
INITIALIZATION Initialization 2.1 INITIALIZATION Initialization This function allows you to set the panel’s programmed memory back to the factory defaults in preparation for system programming. After you select YES to clear a section of memory, the panel asks if you are sure you want to clear the memory. This is a safeguard against accidently erasing part of your programming. No memory is cleared from the programming until you answer YES to the SURE? YES NO option.
COMMUNICATION Communication 3.1 3.2 Communication COMMUNICATION The Communication section allows you to configure the communication settings for the XT30/XT50 panel. After choosing the Communication Type, continue through the list of options. Account Number ACCOUNT NO: Enter the account number sent to the receiver. DD, NET, CELL - The range of account numbers for Digital Dialer, Network, and Cell is 1 to 65535. For account numbers of four digits or less, you do not have to enter leading zeros.
COMMUNICATION 3.9 CHECKIN: - Check-in Minutes 3.10 FAIL TIME: - Fail Time 3.11 COMM TRBL NO YES Enter the number of minutes (3 to 240) between check-in reports for NET Communication. Check-in reports are a method of supervising the panel for communication with the receiver for Net communication. Enter 0 (zero) to disable this feature. The default Check-in Time is 200 minutes. Fail Time allows the receiver to miss a defined number of check-ins before logging that the panel is missing.
COMMUNICATION 3.19 FIRST PHONE NO. - First Telephone Number Enter the first number the panel dials to send reports to this receiver. A phone number may contain two lines of 16 characters to equal 32 characters. You can program a three-second pause in the dialing sequence by entering P. Program a dial tone detect by entering D. These characters are counted as part of the 32 characters.
COMMUNICATION 3.28 O/C USER NO YES Opening/Closing and User Reports 3.29 TEST RPT NO YES Test Report 3.30 FIRST PHONE NO. - YES enables Opening/Closing, Door Access, Schedule and Code Changes, Bypass, and Sensor Reset reports by user to be sent to this receiver. Default is NO. YES enables the Recall Test report to be sent to this receiver. Default is NO. First Telephone Number Enter the first number the panel dials to send reports to this receiver.
NETWORK OPTIONS Network Options Network Options are provided to define the network configuration for the panel. This information will be used during communication of messages via network or Email. Note: IP addresses and port numbers may need to be assigned by the network administrator. When entering an IP, Gateway, or Subnet Mask address be sure to enter all 12 digits and leave out the periods. For example, IP address 192.168.000.250 is entered as 192168000250. 4.1 DHCP 4.
MESSAGING SETUP Messaging Setup 5.1 MESSAGING SETUP Messaging Setup This section allows you to enter the information needed to send and receive messages directly to and from the panel via Email and MyAccess™ text messaging using network or cellular communication. All of the name and password options below allow up to 32 lowercase characters to be entered. The Destination addresses allow up to 48 characters to be entered. System Name is displayed with initial caps.
MESSAGING SETUP 5.9 DESTINATION 3 USER NUMBER: 5.10 EMAIL COMM TYPE NET CELL Email Communication Type 5.11 O/C EMAIL NO YES O/C Email 5.12 O/C SMS 5.13 MONTHLY LIMIT: 5.14 SMTP SERVER - 5.15 SMTP PORT: 5.16 SMTP USERNAME - SMTP Username 5.17 SMTP PASSWORD - SMTP Password 5.18 FROM EMAIL - From Email Address 0 Destination 3 User Number If Destination 3 is a cellular number, enter the user’s User Number for arming/disarming authorization.
DEVICE SETUP Device Setup 6.1 6.2 DEVICE SETUP Device Setup This section allows you to define the XT30/XT50 panel keypad configuration. DEVICE NO:- Device Number Enter the device number of the keypad you are programming. The valid range is 1-8. Note: After you program each option for the first keypad, repeat these programming steps for each additional keypad. 6.3 * UNUSED * Device Name This section allows you to define a 16 character alphanumeric name for the device number.
REMOTE OPTIONS Remote Options 7.1 Remote Options REMOTE OPTIONS This section allows you to enter the information needed for Remote Command/Remote Programming operation. A description of the Remote Options follows: 7.2 RMT KEY: Remote Key 7.3 MFG AUTH NO YES Manufacturer Authorization 7.4 ARMED RINGS: 8 Armed Rings 7.5 DISARM RINGS: 8 Disarmed Rings 7.6 ALR RCVR NO YES Alarm Receiver Authorization 7.
REMOTE OPTIONS 7.8 DISARM 7.9 APP KEY: NO YES Digital Monitoring Products 16 Remote Disarm Enter YES to enable the panel to be disarmed remotely. Selecting NO disables remote disarming. App Key Enter the 8-digit App Key obtained in your Dealer Settings tab at vk.securecomwireless. com. This option is a security feature of the Virtual Keypad iPhone/Android App used only when your Dealer Settings at vk.securecomwireless.com have “EASYconnect” set as the Communication Type.
SYSTEM REPORTS System Reports 8.1 8.2 System Reports SYSTEM REPORTS This function allows you to select the reports the XT30/XT50 sends to the receiver. O/C RPTS NO YES Opening/Closing Reports NO - No Opening/Closing Reports are sent. YES - Sends Opening/Closing Reports for each programmed area. 8.
SYSTEM OPTIONS System Options 9.1 9.2 SYSTEM OPTIONS System Options This section allows you to select system wide parameters used in the operation of the XT30/XT50 system. A description of each System Option follows: SYSTEM: ALL/PERIM System This configures the panel as either a six Area system, an All/Perimeter system AREA A/P H/A (Perimeter/Interior), or a Home/Away system (Perimeter, Interior, and Bedrooms). Zones must be assigned to Bedrooms for the area to be active.
SYSTEM OPTIONS 9.7 CRS ZONE TM: 0 Cross Zone Time Enter the time allowed between zone faults. When a zone programmed for cross zoning faults, the panel begins counting down the Cross-Zone Time entered here. If the same zone or another cross-zoned zone faults within this time, an alarm report is sent to the receiver. If the Cross-Zone Time expires without the second zone fault, only a zone fault report from the first zone is sent to the receiver.
SYSTEM OPTIONS 9.13 ARM ACTY DAYS: 9.14 TIME CHG 0 NO YES HRS FROM GMT: Arm Activity Days This allows selection of the number of days a countdown timer is set for area arming and disarming activity. The range for the countdown timer is 00 to 99. When the timer counts down to zero because of no arming or disarming activity, the panel sends a “No Arming/Disarming” message to the receiver at 10:00 AM. Each time an area is armed or disarmed, the timer is restarted.
SYSTEM OPTIONS 9.16 HOUSE CODE: 0 House Code When using a DMP wireless system, enter a house code between 1 and 50 for the wireless system to use. The DMP wireless receiver automatically programs the house code into the wireless transmitters when the unique transmitter serial number is programmed into the panel. See Wireless programming in Zone Information. Default is 0 (zero) indicating the DMP wireless system is not being used.
BELL OPTIONS Bell Options 10.1 10.2 Bell Options BELL OPTIONS This section allows you to program the panel bell output functions. If using the Model 1135 or 1135DB Wireless Siren for local annunciation, the Trip with Panel Bell option should be selected in the Output Information programming for the siren. BELL CUTOFF: 5 Bell Cutoff Time Enter the maximum time from 1 to 15 minutes the Bell Output remains on.
OUTPUT OPTIONS Output Options 11.1 11.2 Output Options OUTPUT OPTIONS This section allows you to program panel output options. Switched Ground (open collector) outputs are available using the 4-wire output harness on the XT30/XT50 board. Wireless outputs are available when using the built-in 1100 Series Receiver of the XT50 or an 1100D Series Wireless Receiver. Refer to the XT Series Installation Guide (LT-0980) for complete information.
OUTPUT OPTIONS 11.9 BEGIN EXIT: 11.10 END EXIT: 0 11.11 READY 0 11.12 ARMED OUT: 0 11.13 DISARMED OUT: 0 OUT: 0 Begin Exit Output This output/Favorite turns on any time an exit delay time starts. The output turns off when the system arms or when the arming has been stopped. Enter 0 (zero) to disable. End Exit Output This output/Favorite turns on any time an exit delay time ends. The output turns off when the system disarms. Enter 0 (zero) to disable.
OUTPUT OPTIONS 11.17 11.18 Heat Saver Temperature HEAT SAVER TEMPERATURE: 0 Enter the desired temperature setting for all Z-Wave thermostats when the system COOL SAVER TEMPERATURE: 0 Enter the desired temperature setting for all Z-Wave thermostats when the system XT Series Programming Guide is armed ALL or AWAY. When the system is disarmed the thermostats return to their previous settings. The range is 55-95 degrees. Enter 0 (zero) to disable. Cool Saver Temperature is armed ALL or AWAY.
OUTPUT INFORMATION Output Information 12.1 12.2 Output Information OUTPUT INFO This section allows you to program and name wireless outputs into the panel when using an 1100D/1100DH/1100DI Wireless Receiver or the built-in receiver of the XT50. Wireless outputs are also available on the XT50 when using an onboard receiver. Output Number OUTPUT NO: - Enter an output number.
AREA INFORMATION Area Information 13.1 AREA INFORMATION Area Information This section allows you to assign functions to individual areas for XT30 and XT50 panels. All non-24-hour zones must be assigned to an active area. See the section on Zone Information. Activate an area by assigning it a name. A name is given to each active area in place of a number to assist the user during arming and disarming. 13.2 AREA NO: - Area Number 13.3 * UNUSED * Area Name Enter the number of the area to program.
ZONE INFORMATION Zone Information 14.1 14.2 ZONE INFORMATION Zone Information This allows you to define the operation of each protection zone used in the system. Zone Number ZONE NO: - Enter the number of the zone you intend to program. Press COMMAND to enter a zone name. Refer to the Enter Alpha Characters section.
ZONE INFORMATION If you select Blank, Night, Day, Exit, Auxiliary 1, or Auxiliary 2 as the Zone Type, the zone must be assigned to an area. If you select Fire, Panic, Emergency, or Supervisory as the Zone Type, these are 24-hour zones that are always armed and no area assignment is needed. Press COMMAND to continue.
ZONE INFORMATION TGL ARM DIS STEP TGL (Toggle) - When the zone changes from normal to shorted, the programmed areas toggle between the armed or disarmed condition. When restored to normal, no action occurs. When the zone is opened from a normal (disarmed) state, a trouble is reported. When opened from a shorted (armed) state, an alarm is reported and the zone is disabled until you disarm the area(s) from either a keypad or Remote Link™ computer.
ZONE INFORMATION INT This option displays when programming an 1101, 1102, 1103 OR 1106 Transmitter. Select INT to use the internal reed switch contacts. Select EXT to connect an external device to the transmitter’s terminal block. Default is INTERNAL. EXT By allowing both of the Model 1101 or 1103 transmitter contacts (INT and EXT) to be used at the same time, two zones may be programmed from one transmitter. When using both contacts, you must use consecutive zone numbers.
ZONE INFORMATION 14.9.8 NEXT ZN 14.10 NO YES Next Zone Select YES to return to the ZONE NO: - option to program a new zone. Select NO to display the Alarm Action option. 1100 Series Key Fobs For an 1100 Series Key Fob set the House Code from 1 to 50. See House Code programming in System Options. Only zones 31‑34 or 41-44 can be programmed as 1100 Series Key Fob zones.
ZONE INFORMATION 14.10.7 ACTION: ARM DIS XXXXXXX Button Action This option specifies the Button Action for an individual key fob button. The default action for the button selected is displayed. Press any Select key to display the Button Action options. To view more options press the COMMAND key. TGL STA ARM (Arm) - Arms selected areas and force arms bad zones. DIS (Disarm) - Disarms selected areas. TGL (Toggle Arm) - Toggles arm/disarm for selected areas and force arms bad zones when arming.
ZONE INFORMATION 14.10.11 ACTION: Output Action This option allows you to define the output action (STD, PLS, MOM, TGL, OFF) for the selected output number. The default is Steady. STD PLS MOM TGL STD (Steady) - The output is turned on and remains on. PLS (Pulse) - The output alternates one second on and one second off. MOM (Momentary) - The output is turned on only once for one second. TGL (Toggle) - The output alternates between the on state and off state. Each button press toggles the output state.
ZONE INFORMATION 14.12.1 MSG: TROUBLE A T L Message To Transmit You can send two report types to the receiver: Alarm and Trouble. These are represented by the characters A and T. Press any Select key to display the zone report options. - ALARM - Selecting A allows an alarm report to be sent to the receiver and the bell output to activate according to zone type. See the Bell Action section. The zone name appears in the panel’s alarmed zones status lists.
ZONE INFORMATION 14.14 PREWARN:12345678 Prewarn Address Option is only shown for an Exit zone. At the start of the entry delay, all keypad addresses display ENTER CODE: - . If you want the prewarn to sound at all addresses, leave the default as shown. To delete an address, press the matching number on the keypad. To disable prewarning at all keypads, press a top row key to clear the addresses shown. Press the COMMAND key when the address selection is complete.
ZONE INFORMATION 14.20 RECEIVER ROUTING Receiver Routing This option displays if Zone Type is set for Auxiliary 1 or Auxiliary 2. Press any top row key to select the Receiver Routing for the selected zone. NORMAL NORM 1 2 BOTH Select NORM to send Alarm and Supv/Trbl messages from this zone to receiver 1 or receiver 2 as programmed within the receiver. Select 1 to send Alarm and Supv/Trbl messages from this zone to receiver 1 only, regardless of the programming for that receiver.
STOP Stop 15.1 STOP Stop At the STOP option, pressing any Select key allows you to exit the Programmer function of the panel. When selected, the panel performs an internal reset and exits the programmer. The STOP routine causes the following conditions to occur: • All 1100 Series DMP Wireless transmitters are reset to NORMAL • The panel Status List is cleared During the reset, all keypad displays are momentarily blank for two seconds.
APPENDIX Appendix This section of the XT30/XT50 Programming Guide provides additional zone and system information. 17.1 Status List The Status List is the current status of the system or records of recent system events that display on alphanumeric keypads. For example, in Home/Away systems you may see the display SYSTEM READY. If an event were to occur on the system, such as an AC failure, the keypad would also display the AC POWER -TRBL message.
APPENDIX Activate Cell (263C Only) Note: (Version 122 or higher firmware) If the 263C Cellular Communicator has not been previously activated, Automatic Cellular Activation is performed when the panel powers up or is reset. ACTIVATE CELL is only necessary when Automatic Cellular Activation is not successful and communication was not established.
APPENDIX Then, from the panel, enter 984 and the COMMAND key, while the panel is in the Status List. The keypad display changes to NBR PICKUP NET CELL. Select NBR. Enter the phone number for the service receiver connected to the Remote Link computer. Press each number key slowly and deliberately. The panel dials each number as it is pressed. If you make a mistake, press the Back Arrow key. The panel will stop dialing and return to the Status List. You can enter up to 15 characters for the phone number.
APPENDIX WALK TEST STD WLS PIR Walk Test To conduct the Walk Test, reset the control panel by momentarily placing a jumper on J16 then wait one minute. From the keypad, enter the code 8144. The keypad displays WALK TEST. If the system is monitored and the communication type is DD or NET, the system sends a System Test Begin report to the central station. All programmed zones are included in the test.STD (Standard Walk Test) - Select STD to Walk test zones. All programmed zones are included in the test.
APPENDIX 17.6 Keypad Speaker Operation 17.7 Cross Zoning 17.8 Zone Type Descriptions When using LCD Keypads, the panel provides distinct speaker tones from the keypad for Fire, Burglary, Zone Monitor, and Prewarn events. The list below details the conditions under which the speaker is turned on and off for each event. Fire On - Fire zone alarm and Bell Output are ON. Off - Alarm Silence or briefly when a key is pressed. Burglary On - Burglary zone alarm and Bell Output and is ON.
APPENDIX 17.9 Zone Type Defaults The XT30/XT50 panel contains 11 default zone types that provide the most commonly selected functions for their applications. All zone types can be customized by changing the variable options listed below. Key Fob - Indicates if a DMP key fob is programmed. Type - These are the abbreviations displayed on the keypad for the zone types. Area - For a ALL/PERIM or HOME/SLEEP/AWAY system, this is either Interior, Bedroom, or Perimeter. For an AREA system use 1 to 6.
N N N N N N N N N N N Entry Delay 1 or 2 1-2 Prewarn 1 to 8 1-8 Action Message A T L – A A A A A A A A A A Action S S S S S S S S S S Priority - Requires this zone to be in a normal condition before the area can be armed. A T L – A A A A A A A A A A Action S P M F S S S S S 0 0 Low Low Low Low Low Low Low Low Low Low Low Y 4 4 4 4 4 4 4 4 4 4 4 Y Y Y Y Y Y Y Y Y Y Y Y Style - The abbreviations that display on the keypad for arming zone style.
APPENDIX 17.10 Common Keypad Messages Message Meaning Possible Solutions INVALID CODE The user code you have entered is not recognized by the system. Check the user code and try again. CLOSING TIME The schedule has expired but the system has not been armed. Users still on the premise should arm the system or extend the schedule to a later time. KEYPAD NAME - NOPWR Keypad is not getting proper power. Check that AC/DC transformer is plugged in correctly.
REVISIONS Revisions to This Document This section explains the changes made to this document during this revision. It lists the date and identifies the change(s) made, the related section number and section heading, and a summary of the change. Ver. Section Number and Heading 1.12 13.3 Area Name Listings and Approvals 1.11 Entire Document 1.6 Keypads 1.7 Special Keys 1.8 Entering Alpha Characters 1.10 Keypad Displays Current Programming 3.4 Communication Type 10.21 Weather Zip Code 18.
800 - 641 - 4282 INTRUSION • FIRE • ACCESS • NETWORKS www.dmp.com 2500 North Partnership Boulevard Designed, Engineered and Assembled in U.S.A. S p r i n g fi e l d , M i s s o u r i 6 5 8 0 3 - 8 8 7 7 15065 California State Fire Marshal (CSFM) ANSI/SIA CP-01 False Alarm Reduction ANSI/UL 1023 Household Burglar ANSI/UL 985 Household Fire Warning ANSI/UL 1610 Central Station Burglar ANSI/UL 1635 Digital Burglar FCC Part 68 Registration ID: CCKAL00BXT50 LT-0981 1.
