User's Manual

ManualsBrandsDigital Security Controls ManualsElectronicsAlarm Transceiver

Warning – This manual contains information on limitations regarding product use and function and

information on the limitations as to liability of the manufacturer.

Attention – Ce manuel contient des informations sur les restrictions concernant le fonctionnement et

l’utilisation du produit et des informations sur les restrictions en ce qui concerne la responsabilité du

fabricant. La totalité du manuel doit être lu attentivement.

Advertencia – Por favor consulte el Manual de Instrucciones del Sistema para más información

acerca de las limitaciones conrelación al uso y funcionamiento del producto e información acerca de

las limitaciones como la responsabilidad del fabricante.

Importante – Questo manuale contiene informazioni sulle limitazioni riguardanti l’uso e la funzione

del prodotto, ed informazioni circa i limiti di responsabilità del produttore. Si consiglia di leggere

attentamente l’intero manuale.

WAARSCHUWING

– Deze handleiding bevat informatie over de beperkingen in verband met het

gebruik en de functies van het product en over de beperkingen van de verplichtingen van de fabrikant.

TR5164

Installation Instructions, Instructions d’installation, Instrucciones de

Instalación, Manuale d'installazione, Installatie handleiding

TR5164-433

Version 1.0

DRAFT

Summary of content (23 pages)

PAGE 1
TR5164 D R AF T Installation Instructions, Instructions d’installation, Instrucciones de Instalación, Manuale d'installazione, Installatie handleiding TR5164-433 Version 1.0 Warning – This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
PAGE 2
Warning Please Read Carefully Note to Installers This warning contains vital information. As the only individual in contact with system users, it is your responsibility to bring each item in this warning to the attention of the users of this system. System Failures • Inadequate Installation A security system must be installed properly in order to provide adequate protection. Every installation should be evaluated by a security professional to ensure that all access points and areas are covered.
PAGE 3
Limited Warranty D R AF T Digital Security Controls warrants the original purchaser that for a period of twelve months from the date of purchase, the product shall be free of defects in materials and workmanship under normal use. During the warranty period, Digital Security Controls shall, at its option, repair or replace any defective product upon return of the product to its factory, at no charge for labour and materials.
PAGE 4
Section 1: Table of Contents T Use this manual in conjunction with the Installation Manual of the alarm control panel. AF Section 1: Introduction .................................. 3 1.1 TR5164 Installation Procedure ....... 3 1.2 Specifications and Features ............. 3 1.3 Compatible Wireless Devices ......... 4 1.4 Safety Instructions ........................... 4 Section 2: TR5164 Set Up & Wiring ........... 5 2.1 Unpack the TR5164 ......................... 5 2.
PAGE 5
Section 1: Introduction This manual describes how to install, program and maintain the TR5164. Before installing the TR5164 module, complete the following steps: 1. Plan the placement and wiring of the security system (see the system Installation Manual). 2. Install the control panel, then install and enroll at least one keypad to use for programming. 3. Install and enroll any hardwired zone expander modules (PC5108).
PAGE 6
1.3 Compatible Wireless Devices Please refer to the instruction sheets of the following devices for more information.
PAGE 7
Section 2: TR5164 Set Up & Wiring This section describes how to set up and wire the TR5164 module. 2.1 Unpack the TR5164 Check that the following parts are in the package: • TR5164 PCB • TR5164 plastic cabinet • Hardware for mounting the cabinet 2.2 Choose a Mounting Location for the TR5164 AF T NOTE: Permanently mount the TR5164 receiver and wireless devices after placement testing each device (Section 5.1, page 11).
PAGE 8
Section 3: Receiver Programming Enrollment consists of programming the device’s Electronic Serial Number (ESN) into the TR5164 so that it can be identified when an event is communicated. The ESN is located on the back of each wireless device. NOTE: When programming via hardwired keypad, wireless key programming sections 001-064 and 101-116 only accept 6 digits. To program 8-digit ESNs, only use the last 6 digits.
PAGE 9
4. After successful confirmation of the ESN, the system prompts for the zone/slot number. • The next available slot for the device type is displayed. Press [,] to accept or enter the slot number. • To re-enroll a wireless key press simultaneously for approximately 3 seconds. 3.4 Manually Enroll Wireless Devices/Keypads To manually enroll a 2-way wireless device: 1. Enter [,][8][Installer Code][804]. 2.
PAGE 10
Section 4: Other Programming 4.1 Program Zones and Partitions Once all wireless devices are enrolled, complete zone programming on the system. Although the exact programming required varies depending on which control panel the TR5164 is connected to, ensure that the following programming options are completed correctly for each wireless zone: • Enable zones and/or assign zones to one or more partitions (programming sections [202] to [265]).
PAGE 11
4.3 Enable Supervision of Wireless Zones AF T Each wireless device (excluding wireless keys) sends a supervisory signal periodically. If the receiver does not receive a signal within the time programmed for the Wireless Supervisory Window, it generates a supervisory fault. NOTE: For wireless supervision to work, enable the wireless zone attribute on all wireless zones (sections [101] to [164], option [8] ON). To program the wireless supervisory window: 1.
PAGE 12
3. Enter programming section [141] to [156] for wireless keys 1-16. 4. For each of the available buttons on the wireless key, enter the 2-digit number corresponding to the selected function. See “Wireless Key Function Key Options” on page 17 for a list of function key options. 5. Record all programming choices in the worksheets in the back of the manual. 6. To exit press [#]. For more information on programming wireless key function buttons, refer to the wireless key installation sheet. 4.
PAGE 13
Section 5: Testing & Mounting 5.1 Test the Reception of Wireless Devices Testing the proposed placement of each wireless device before it is mounted is very important. Following these steps tests the signal strength between the TR5164 and the wireless devices. All wireless devices can be tested together (global placement testing) or individually. NOTE: After the wireless devices are enrolled, Installer Programming must be exited and then re-entered at least once before performing a placement test.
PAGE 14
Testing Individual Wireless Keys Do not use the individual device test described above to test wireless keys. To ensure that the TR5164 is receiving transmissions from these devices, use the function keys on the wireless keys at several different points throughout the installation. NOTE: Two-way wireless keys must be activated by pressing any key before they become functional. 5.
PAGE 15
Section 6: Additional Notes 6.1 Trouble Conditions AF T The control panel constantly monitors for possible trouble conditions. If a trouble condition is detected, the keypad beeps and the “Trouble” light turns on. Press [,][2] to display trouble conditions. The following trouble conditions apply to the TR5164 and/or any enrolled devices. • RF Jam Detected (on Power panels v.2.01 and below) - This trouble is generated when the TR5164 detects an RF Jamming condition.
PAGE 16
Section 7: Troubleshooting D R AF T 1. When I enter the 3-digit zone number for adding a wireless device, the keypad gives me a long beep. ESNs can be entered only when a TR5164 wireless receiver is connected to the Keybus. See Section 2.3, page 5 for instructions on setting up and wiring the TR5164 module. 2. I have entered the ESN for the device but when I activate it, the zone does not show open on the keypad. Check the following: • Ensure the ESN has been entered correctly.
PAGE 17
Section 8: Programming Worksheets TR5164 Wireless Programming Use the following worksheets to record wireless device programming options for future reference. [804] Zone Serial Numbers (for wireless devices, repeaters and keypads) Wireless keypads 1-4 must be enrolled into zones 29-32 respectively. All other wireless devices may be enrolled into any of the remaining 60 zones.
PAGE 18
[804][081] Wireless Supervisory Window (Default = 96) The window is programmed in 15 minute increments. The default programming is: • 96 (x15minutes), which is equal to 24 hours (NA), or • 8 (x15minutes), which is equal to 2 hours (EU). Valid entries are (004) to (096), equal to 1 to 24 hours. [804][082]-[089] Zone Transmitter Supervision Options 3 4 5 6 7 8         [086] Opt 1 2 3 4 5 6 7 8 Def.                 Zones 9-16 [084] Def.
PAGE 19
[804][101]-[116] Wireless Key Serial Numbers [101] [109] [102] [110] [103] [111] [104] [112] [105] [113] [106] [114] [107] [115] [108] [116] Wireless Key Function Key Options Entry Key Description T Key Description Null Key 17 [,][1] Activate Stay/Away For Future Use 18 Global Away Arm Stay Arm 19 [,][7][3] Command Output #3 Away Arm 20 For Future Use [,][9] No-Entry Arm 21 [,][7][4] Command Output #4 [,][4] Chime ON/OFF 22 Global Disarm [,][6][code][4] System Test 23-26 For Future Use F
PAGE 20
[804][141]-[156] Wireless Function Key Options Function 1 Function 2 Function 3 Function 4 Function 5 Function 6 Default 03 Default 04 Default 27 Default 30 Default 13 Default 14 [141] Key 1 [142] Key 2 [143] Key 3 [144] Key 4 [145] Key 5 [146] Key 6 [147] Key 7 [151] Key 11 [152] Key 12 [153] Key 13 [154] Key 14 [155] Key 15 AF [150] Key 10 D R [149] Key 9 T [148] Key 8 [156] Key 16 NOTE: Functions 5 and 6 are for WT4989 only.
PAGE 21
[804][181]-[182] Enable/Disable 2-Way Wireless Keys 1-16 Opt Def. ON OFF Opt Def.
PAGE 22
[804][900] General Wireless Options Opt Def 1 2 3  4 5  6 7  8 ON         Def OFF Future Use Future Use Wall Tamper Disabled EN Case Tamper Disabled EN Wireless Delinquency Disabled EN    Wall Tamper Enabled  RF Jam Enabled Case Tamper Enabled Wireless Delinquency Enabled Future Use EN RF Jam Disabled Future Use T [904] Wireless Device Placement Test See “Testing Individual Devices” on page 11 for details. AF 8.
PAGE 23
FCC Compliance Statement +HUHE\ '6& GHFODUHV WKDW WKLV GHYLFH LV LQ FRPSOLDQFH ZLWK WKH HVVHQWLDO UHTXLUHPHQWV DQG RWKHU UHOHYDQW SURYLVLRQV RI 'LUHFWLYH (& 7KH FRPSOHWH 5 77( 'HFODUDWLRQ RI &RQIRUPLW\ FDQ EH IRXQG DW KWWS ZZZ GVF FRP OLVWLQJVBLQGH[ DVS[ &=( '6& MDNR Y¿UREFH SURKODģXMH ŀH WHQWR Y¿UREHN MH Y VRXODGX VH YģHPL UHOHYDQWQ¯PL SRŀDGDYN\ VPÝUQLFH (& '$1 '6& HUNO¨UHU KHUYHG DW GHQQH NRPSRQHQWHQ RYHUKROGHU DOOH YLNWLJH NUDY VDPW DQGUH EHV