VOYAGER Manual April 2019
VOYAGER User Manual Table of Content Voyager App Technical specs What is in the Box: Interface WiFi Control Client status via Bluetooth Charging/StandBy WiFi reset 3 4 5 6 8 10 11 12 2
VOYAGER User Manual Voyager App The Voyager Smart Light is a fixture combining light source, battery, and remote control into one. All that is required is a smartphone, tablet or computer to act as interface. Voyager App To control Voyagers, it is necessary to download the Voyager app available on Google Play Store, Apple App Store or www.digitalsputnik.com Opening the latest release of the app will cause all connected Voyagers to update automatically. This user manual covers features up until v1.3.
VOYAGER User Manual Technical specs Technical specs 4 ft. Dimensions: 1226x62x50mm (44"x 2.5"x 2") Resolution: 83 pixels Weight: 2.2kg (4.86lbs) Power draw: 40W Battery: 90Wh 2 ft. Dimensions: 610x62x50mm (24"x 2.5"x 2") Resolution: 42 pixels Weight: 1.1kg (2.43lbs) Power draw: 20W Battery: 45Wh Input on light: 19VDC 4.74A Input on charger: 100-240VAC 50/60Hz Voyagers are fully submersible down to 33ft/10m.
VOYAGER User Manual What is in the Box What is in the Box: 2’/4’ Voyager Light Tube - The Complete All in one Light Tube System. • The Voyager has a clear plastic diffusion sheath that comes off completely and has a lip inside the rim to hold cut diffusion. • The provided diffusion sheath comes with a Rosco E400 ROLUX filter. • Quick attach rail system on the back of the Voyager supports the DS Voyager Mount. DS Voyager Mount - Claw type mount that can attach itself to the back of the Voyager.
VOYAGER User Manual Interface Interface Front button: Power button Charging/Data port Side button: Program button When booting unit ON for the first time after unboxing, the unit must be connected to the power adapter*. * All units are delivered in shelf mode to extend battery life. If you plan to store your units for longer periods of time, or to prepare them for air travel, hold down both buttons for +- 10 seconds. This is also the factory reset procedure.
VOYAGER User Manual Interface 1st led: Power Mode 3rd led: WiFi Mode Green: Voyager is ON and fully booted. Blue: Voyager is booting (takes about 40 seconds). Red: Voyager has been switched off. Yellow: Voyager is charging/StandBy. 1st led: Power Mode 3rd led: WiFi Modes (please see the WiFi Control section below for more detailed information) Yellow: Master (default mode). Unit is creating its own WiFi network, and can be connected to a remote device. Blue: Router.
VOYAGER User Manual WiFi Control WiFi Control To toggle between WiFi modes, use the program button. Pressing the program button for 8 seconds will cause the Voyager to toggle between Master, Router and Client modes. Modes will always cycle in this order: MASTER > ROUTER > CLIENT. The unit must first be allowed to fully boot in order to toggle between WiFi modes. When using a single Voyager, make sure the unit is in Master mode -identifiable by a Yellow third diode when briefly pressing the power button-.
VOYAGER User Manual WiFi Control When working with more than 7 Voyagers, you will need to connect to them using an external router. For that, all Voyagers must be connected to the external router’s network. This can be achieved using the Voyager App. In the Setup tab > Lamp Settings > Select lamp/lamps* to be made into clients > Choose a Network from the available network list displayed in the app OR type in the network name>Password>Connect. Then, connect your device to the same router.
VOYAGER User Manual Client status via Bluetooth Client status via Bluetooth It is also possible to verify a Voyagers WiFi connection when in "Client" mode via Bluetooth. For this, open your device’s Bluetooth list and lamps in client mode will show up: Lamps SSID (DS026XXXXXXXXXX)-> Connected SSID (VoyagerRouter) If there is an issue with the password, it will show "PASS" and if there is no WiFi to connect to, it will show "SSID".
VOYAGER User Manual Charging/StandBy Charging/StandBy A Voyager can be charged while being actively used. Plugging a powered-off Voyager to a charger will cause it to start charging and enter standby mode. The StandBy mode is indicated by a yellow first diode when checking the Voyager’s status. A Voyager in StandBy mode will be fully active (including WIFi module and animation engine), with the exception of the light output being turned down.
VOYAGER User Manual WiFi reset WiFi reset It is recommended to be performed when encountering errors in communication. To perform a WiFi reset, press the side button for +- 10 seconds. The 3rd diode becoming white will indicate the WiFi reset has been registered.
