Quick Start Guide

ManualsBrandsDigital Watchdog ManualsBullet Cameras5 Megapixel Outdoor IR Bullet Camera, 2.8mm Lens

Quick Start Guide Quick Start Guide

1. The mounting surface must withstand three times the weight of your camera.

2. Do not let the cables get caught in improper places or the electric line cover

can be damaged. This may cause a short or re.

3. Using the mounting template sheet or the camera itself, mark and drill the

necessary holes in the wall or ceiling.

6. Mount the rubber plug to the gap of the mounting base. Then secure the

mounting base with camera to the wall with screws.

7. Adjust the camera to obtain an optimum angle by using the camera’s

bracket. The camera’s max angles are:

Pan: 0°~ 360°

Tilt: 0°~ 90°

When the proper view has been achieved, tighten the xed screws to nish

the installation.

8. If your camera supports a varifocal lens (DWC-B8563TIR models only), you

can adjust the camera’s zoom and focus from the camera’s OSD menu via

UTC. See the user manual for more information.

9. Remove the protection lm softly to nish the installation.

4. Pass the wires through the mount bracket and make all necessary

connections. Connect the BNC cable and power cables to the camera.

STEP 1 – PREPARING TO MOUNT THE CAMERA

STEP 4 – INSTALLING THE CAMERA

STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES

NOTE: Download All Your Support Materials and Tools in One Place

1. Go to: http://www.digital-watchdog.com/support-download/

2. Search your product by entering the part number in the ‘Search by Product’ search

bar. Results for applicable part numbers will populate automatically based on the

part number you enter.

3. Click ‘Search’. All supported materials, including manuals and quick start guide

(QSGs) will appear in the results.

Tel: +1 (866) 446-3595 / (813) 888-9555

Technical Support Hours:

9:00AM – 8:00PM EST, Monday thru Friday

digital-watchdog.com

Attention: This document is intended to serve as a quick reference for initial

set-up. It is recommended that the user read the entire instruction manual for

complete and proper installation and usage.

DWC-B8553TIR DWC-B8563TIR

Template

Sheet

Rubber

Plug

WHAT’S IN THE BOX

QSG Manual 1 Set

Tapping

Screws PA

3x25 – 3pcs

1 Set

Mounting

Template

1 Set

Plastic Plugs

– 3pcs

1 Set

Rubber Plug 1 Set

Machine

Screw PWM

3x5 – 1pc

1 Set

Video Output

Video Switch Cable

Power Cable

Power Cabl e

V i deo Output

V i deo Swi tch Cable

Rotation: 0° ~ 360°

Tilt: 0° ~ 90°

Rev Date: 11/18

Specications and pricing are subject to change without notice.

STEP 3 – CHANGING SIGNAL IN THE CAMERA

The camera supports three analog signals: HD-Analog, HD-TVI, HD-CVI and

analog signal up to 960H.

5. In order to swith the camera’s signal between the available options, locate

the button switch on the signal cable. The video outputs will recycle by

holding and pressing the button in the video switch cable for 5 seconds.

Power Requirements Power Consumption

12VDC ONLY!

CAUTION! The camera supports DC power supply only

IR on: < 4W

IR off: < 1W

NOTE: The camera’s factory default resolution is 4MP at 30fps. However, the camera

can display video up to 5MP resolution at 20fps. In order to change the camera’s

resolution, go to the camera’s OSD menu > ADJUST > OUTPUT MODE.

1. AF MODE SEMI

2. ONE SHOT AF

3. TDN AF OFF

4. LENS INIT

5. RETURN RET