Quick Start Guide

NOTE: Download All Your Support Materials and Tools in One Place
1. Go to: http://www.digital-watchdog.com/support-download/
2. Search your product by entering the part number in the ‘Search by Product’ search
bar. Results for applicable part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals, Quick Start Guides
(QSG), software and rmware will appear in the results.
WHAT’S IN THE BOX
QSG Manual 1 Set
Mount Bolt &
Nut – 2pcs
1 Set
L-W r e n c h 1 Set Mount Plate 1 Set
Template
Sheet for
installing by
Bolt & Nut
1 Set
Screw &
Plastic Anchor
– 3pcs
1 Set
Template
Sheet for
installing by
Plate
1 Set
Waterproof
Cap
1 Set
Test Monitor
Cable
1 Set
1. The mounting surface must bear ve times the weight of your camera.
2. Do not let the cables get caught in improper places or the electric line cover
to be damaged. This may cause a breakdown or re.
3. For the installation process, remove the dome cover from the camera module
by loosening the three (3) screws on the dome. Use the wrench provided with
the camera.
4. Using the mounting template sheet or the camera itself, mark and drill the
necessary holes in the wall or ceiling.
6. Attach the main body to the mount bracket by tightening the lock screw
using the six-angle wrench.
7. For soft installation surfaces, use the included metal mount plate. Fix the
mount plate on the mounting surface using the included screws. Then, press
the bottom case onto the mount plate. The three bezels on the case will align
and snap lock onto the plate.
8. To use the camera’s water proof wiring:
(1). Install the LAN cable into .
(2). will be assembled to with a 1/4 turn.
(3). Thread tightly to .
9. Use the camera’s 3-Axis gimbal to adjust the camera’s tilt and angle. The
camera’s maximum tilting angle is 70°.
10. Assemble the dome cover over the camera body and detach the protecting
lm from the dome bubble.
5. Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE Switch, connect the
camera using an Ethernet cable for both data and power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch, connect
the camera to the switch using an Ethernet cable for data transmission
and use a power adapter to power the camera.
Power Requirements Power Consumption
DC 12V
PoE IEEE 802.3af / PoE Class 2
LED Off: 3W, 250mA
LED On: 4W, 330mA
POWER
NETWORK
1
2
3
5
4
Template
Sheet
Reset
Button
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday thru Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
DWC-MF4Wi4
DWC-MF4Wi6
DWC-MF4Wi8
Quick Start GuideQuick Start Guide
Default Login Information
Username: admin Password: admin
STEP 1 – PREPARING TO MOUNT THE CAMERA
STEP 3 – INSTALLING THE CAMERA
STEP 2 – CABLING THE CAMERA TO EXTERNAL DEVICES
Resetting the camera: To reset the camera, use the tip of a paper clip
or a pencil and press the reset button. Pressing the button for ve (5)
seconds will initiate a camera-wide reset of all the settings, including
network settings.
a
b
c
a
a
b
b
c
8
NOTE: To ensure moisture seal, make sure the o-ring is in place between
and . In extreme environments use of an outdoor rated
sealer is recommended.
a
b
NOTE: When using the waterproof cap, crimp the RJ45 connector after
passing the cable through the waterproof cap.