Quick Start Guide

STEP 3 – INSTALLING THE CAMERA
DWC-MVA2WiAT
STEP 1 - PREPARING TO MOUNT THE CAMERA
1. The mounting surface must withstand five times the camera weight.
2. Do not let the cables get caught in improper places or the electric line
cover can be damaged. This may cause a short or fire.
3. For the installation process, remove the dome cover from the camera
module by loosening the three (3) screws on the dome. Use the
wrench provided with the camera.
4. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
Quick Start Guide
Quick Start Guide
WHAT’S IN THE BOX
Torx®
wrench
1
Mounting
template
1
Screws and
plastic
anchors –
2pcs
1 set
Quick setup
guide
1
Waterproof
cap and
gasket
1
Tel: [phone]
Technical Support Hours:
9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for the initial
set-up. It is recommended that the user read the entire instruction manual for
complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Screw &
Plasc Anchor-3pcs
Template Sheet
for installing by Plate
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut Mount Plate Torx Wrench
Waterproof cap & Gasket
Quick Manual &
Download Guide
Moisture absorber
& Absorber Guide
Test Video Cable
Screw &
Plasc Anchor-3pcs
Template Sheet
for installing by Plate
Template Sheet
for installing by Bolt & Nut
Mount Bolt & Nut Mount Plate Torx Wrench
Waterproof cap & Gasket
Quick Manual &
Download Guide
Moisture absorber
& Absorber Guide
Test Video Cable
Ethernet
Cable
1
Pass the wires through the mount bracket and make all necessary
connections.
1. NETWORK CONNECTIONS – If you are using a PoE Switch, connect
the camera using an Ethernet cable for both data and power.
2. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power requirements Power consumption
DC 12V, PoE (IEEE 802.3af Class 3).
(Adapter not included)
DC12V: max 6.4W
PoE: max 7.6W
Power
Ethernet
Cable
2
a
b
c
1. To use the camera’s waterproof wiring:
a. Install the LAN cable into .
b. will be assembled
to with a 1/4 turn.
c. Thread tightly to .
a
a
b
bc
Panning
360°
Rotation
360°
Tilting 90°
Mounting
template
2. Once all cables have been connected, use the screws included with
the camera to properly mount and secure the camera to the
mounting surface.
NOTE: To ensure moisture seal, make sure the o-ring is in place
between and . In extreme environments use of an
outdoor rated sealer is recommended.
a
b
NOTE: When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
3. Adjust the camera’s pan, tilt and
position to achieve the desired view.
The cameras’ max angles are:
Pan: 0° ~ 360°
Tilt: 0° ~ 90°
Rotation: 0° ~ 360°
3. Once the installation is complete,
tighten the pan/tilt/rotation screw
until it’s secure.
Default Login Information: admin | admin
When logging into the camera for the first time, you will be prompted
to set up a new password. You can set the new password using the
DW® IP Finder™ software or directly from the camera’s browser menu.
Resetting the camera: To reset
the camera, detach the ball
module from the base by rotating
it counter-clockwise. See the
diagram on the bottom right.
Do not touch any other parts of
the camera.
Press the reset button on the
base of the camera’s lens module.
Pressing the button for five (5)
seconds will initiate a camera-wide
reset of all the settings, including
network settings.
When replacing the camera’s
ball module back into place,
make sure no cables are caught
or got disconnected. Rotate the
ball module clockwise until it is
secured in place.