Quick Start Guide

Quick Start Guide
Tel: [phone]
Technical Support Hours:
9:00 AM – 8:00 PM EST, Monday through Friday
digital-watchdog.com
DWC-PVF9Di2TW
WHAT’S IN THE BOX
Quick setup and
download guides
1 set
Mount bolts
and nuts –
2pcs
1 set
Metal mounting
plate
1
Screws and
plastic anchors
– 3pcs
1 set
Mounting
template for bolt
and nut
installation
1
Waterproof
cap
1 set
Mounting
template for metal
plate installation
1
Hex Allen
wrench
1
Pass the wires through the mount bracket and make all necessary
connections.
a. NETWORK CONNECTIONS – If you are using a PoE switch,
connect the camera using an Ethernet cable for both data and
power.
b. NETWORK CONNECTIONS – If you are using a non-PoE switch,
connect the camera to the switch using an Ethernet cable for data
transmission and use a power adapter to power the camera.
STEP 2 – CABLING THE CAMERA TO
EXTERNAL DEVICES
Power Requirements Power Consumption
DC12V, PoE IEEE 802.3af
Class 3 (Adapter not
included)
DC12V: max 8.5W
PoE: max 10W
POWER
NETWORK
Mounting template
a
b
c
1. Once all cables are connected, secure the camera to the mounting
surface using the included screws.
2. For soft installation surfaces, use the included metal mount plate. Fix
the mounting plate on the mounting surface using the
included screws. Then, press the bottom case onto
the mounting plate. The three bezels on the case will
align and snap lock onto the plate.
3. To use the camera’s waterproof wiring:
(1). Install the LAN cable into .
(2). will be assembled to with a 1/4 turn.
(3). Thread tightly to .
STEP 3 – INSTALLING THE CAMERA
a
a
b
b
c
NOTE: When using the waterproof cap, crimp the RJ45
connector after passing the cable through the
waterproof cap.
1. The mounting surface must bear five times the weight of your
camera.
2. Do not let the cables get caught in improper places or the electric line
cover to be damaged. This may cause a breakdown or fire.
3. Using the mounting template sheet or the camera itself, mark and drill
the necessary holes in the wall or ceiling.
STEP 1 – PREPARING TO MOUNT THE CAMERA
NOTE: To ensure moisture seal, make sure the o-ring is in place
between and . In extreme environments use of an
outdoor rated sealer is recommended.
a
b
4. Re-attach the camera’s gasket ring and dome to the
camera module by aligning the screw holes. Be sure
to align the wedge on the side of the camera with
the one on the mounting bracket.
Installation using mount bolt and screws:
1. Using the template sheet for the nuts and bolts
installation, mark and drill the holes on the mounting
surface.
2. Secure the two long mounting screws to the
camera’s base.
3. Pass the wires through the mount bracket and make
all necessary connections.
4. Mount the camera to the mounting surface by using
the 2 mounting nuts. Rotate the locking discs over
the screws until the camera is held tightly from the
mounting surface.
5. Re-attach the camera’s gasket ring and dome to the
camera module by aligning the screw holes. Be sure
to align the wedge on the side of the camera with
the one on the mounting bracket.
Attention: This document is intended to serve as a quick reference for the
initial setup. It is recommended that the user read the entire instruction manual
for complete and proper installation and usage.
NOTE: Download all your support materials and tools in one place
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the
‘Search by Product’ search bar. Results for applicable
part numbers will populate automatically based on the
part number you enter.
3. Click ‘Search’. All supported materials, including manuals
and quick start guide (QSGs) will appear in the results.
Reset Button
Resetting the camera: To reset the camera, use the tip of a
paper clip or a pencil and press the reset button. Pressing the
button for five (5) seconds will initiate a camera-wide reset of
all the settings, including network settings.
Default Login Information: admin | admin
When logging into the camera for the first time, you will be prompted
to set up a new password. You can set the new password using the
DW® IP Finder™ software or directly from the camera’s browser menu.