Setup guide

Please refer to the table below for the default camera settings.
You can reset the camera’s settings to its default color settings by
pressing the ‘Default’ button at the bottom of the screen.
DWC-MF21M4TIR
DWC-MF21M8TIR
IP 2.1MP Low Profile Vandal Dome IR Camera
Recommended Settings
Camera Default Color Settings
Adjusting the Camera’s Angle
Installation Using Mount Plate
1. Detach the camera’s cover dome
from the camera’s module by
unscrewing the three cover dome
screws.
2. Using the metal mount plate, mark
and drill the necessary holes in the wall
or ceiling.
3. Pull wires through and make
connections.
4. Using the three (3) included screws,
mount and secure the camera to the
wall or ceiling.
5. Attach the camera base to the metal
mount by snapping it into place using
the two metal handles.
6. Secure the camera’s cover dome
onto the camera base to complete the
installation.
Easy Camera Installation
INSTALLATION
Network Connection
There are two options.*
Using a Non-PoE Switch
!
Frequent use may cause a System Error
Using a PoE-Enabled Switch
The MEGApix Camera is PoE-compliant, allowing transmission of power
and data via a single ethernet cable. Follow the illustrations below to
connect the camera to a PoE-enabled switch using an ethernet cable.
If a PoE-enabled switch is not used, use a power adaptor to connect the
MEGAPIX Camera to a Non-PoE switch.
5
7 8
Parts and Description
Pressing the reset button on the camera’s control board for five (5) seconds will
initialize all environmental variables to factory default. Previous setup for IP default,
time, etcetera will be deleted. If a system IP address is lost, reset the camera back
to factory default.The following are the default network settings:
IP Mode DHCP
IP Address 192.168.1.123
Subnet Mask 255.255.255.0
Gateway 192.168.1.123
Command Port 7000
HTTP Port 80
Live Port 7001
Resetting the Camera
NETWORK
ENVIRONMENTAL
Frame Rate Up to 30fps at All Resolutions
Video Compression Type H.264, MPEG4, MJPEG (Super Fine~Low)
IP IPv4, IPv6
Protocol TCP/IP, HTTP, DHCP, PPPoE, ICMP, ARP, RARP,
RTSP, NTP, UDP, Multicast
LAN 802.3 Compliance 10/100 LAN
Web Viewer OS: Windows XP / Vista / 7, MAC OS
Browser: Internet Explorer, Chrome, Firefox, Safari
Video Management Software NxMS, DW Spectrum, Pivot
ONVIF Conformance Yes
Streaming Capability Dual-Stream at Different Rates and Resolutions
Power Requirement DC 12V, PoE (IEEE802.3af Class 2)
Power Consumption 3.6W, 300mA / LED ON: 4.3W, 360mA
Operating Humidity Less than 90% (Non-Condensing)
Operating Temperature/ Humidity -10
o
C ~ 50
o
C (14
o
F ~ 122
o
F)
Other Certifications CE, FCC, RoHS
Memory Slot 24 hours recording to Micro SDHC Card (4GB-32GB)
Card Not Included*
Dimensions 125 x 74.3 mm (4.9 X 2.9 in)
Material Aluminum Housing
Weight 1.0 lbs
Maximum User Access 5 Users
MECHANICAL
ELECTRICAL
Resolution 1920X1080 (16:9) ~ 320X240 (4:3)
IP Rating IP66 (Protects against dust and high pressure water)
LENS
IMAGE
Image Sensor 1/2.8” Sony CMOS Sensor
Effective Pixels 1920 (H) X 1080 (V)
Minimum Scene Illumination F2.0 (30IRE): 2.4 Lux [Color], F2.0 (30IRE): 0.5 Lux [B/W]
Zoom 12x Digitzl Zoom
Lens Type Fixed Lens
Focal Length 4.0mm [DWC-MF21M4TIR] / 8.0mm [DWC-MF21M8TIR]
Angle of View Horizontal: 42
o
Wide Angle
IR Distance 30ft Range IR
Quick Setup Guide
1. Detach the camera’s cover dome from the
camera’s module by unscrewing the three
cover dome screws using the L-Wrench.
2. Use the camera or mounting template to
mark and drill the necessary holes in the
wall or ceiling.
3. Pull wires through and make connections.
4. Using three (3) included screws mount
and secure the camera to the wall or ceiling.
5. Secure the camera’s cover dome onto the
camera base to complete the installation.
Installation Using Mount Bolt & Nut
1. Detach the camera’s cover dome
from the camera’s module by
unscrewing the three cover dome
screws.
2. Using the camera or mounting
template, mark and drill the necessary
holes in the wall or ceiling.
3. Secure the two long mounting
screws to the camera’s base.
4. Pull wires through and make
connections.
5. Mount the camera to the mounting
surface using the 2 mounting nuts.
6. Secure the camera’s cover dome
onto the camera base to complete the
installation.
Reset Button
DC Power Cable
Lens
Tilt Stopper Screw
Reset Button
RJ-45 Cable
Micro SD Card Slot
To adjust the camera’s orientation:
1. Loosen the tilt stopper screw at the
base of the camera’s Gibmal by
rotating it counter clock-wise.
2. Move the camera to the desired
angle.
3. Secure the camera’s lens position by
screwing the tilt stopper screw
clock-wise.
Template Sheet
Template Sheet
Thank you for purchasing Digital Watchdog’s MEApix Flat Vandal Dome Camera.
Before installing the camera, please verify your model and read this guide carefully.
20140122
The following items are included with your MEGApix Camera
L-Wrench
Low Profile Vandal
Dome IR Camera
- 12VDC Power
- RJ45 Network
PREPARATION
TEL: [phone]
www.Digital-Watchdog.com / [e-mail]
Technical Support Hours: Monday-Friday 9:00AM to 8:00PM EST
INSTALLATION
2 Mounting Nuts
& 2 Mounting
Screws
Metal Mount Plate
Quick Start
Guide
Mounting
Template for
Camera and
Metal Mount
Plate
CD
(Manual &
Software)
1
2
2 3 4
6
SPECIFICATIONS
Camera Specifications
3 Screws & 3
Dry Wall
Anchors
DWC-MF21M4TIR
DWC-MF21M8TIR
IP 2.1MP Flush Mount Vandal Dome IR Camera
Quick Setup Guide
22