Service Maintenance Manual MCS LOGISTICS ENGINEERING PRIORIS XL Server K-MN-SD00000-05-JG00.
November 1995 The information in this document is subject to change without notice and should not be construed as a commitment by Digital Equipment Corporation. Digital Equipment Corporation assumes no responsibility for any errors that might appear in this document. The software, if any, described in this document is furnished under a license and may be used or copied only in accordance with the terms of such license.
Digital PRIORIS XL Server Table of Contents Table of Contents PREFACE ............................................................................................................................................................. 9 CHAPTER 1 PRODUCT DESCRIPTION .................................................................................................... 11 PRODUCT INTRODUCTION .............................................................................................................................
Table of Contents Digital PRIORIS XL Server CHAPTER 3 SERVICE PROCEDURES ...................................................................................................... 35 P R I O R I S X L SAFETY REQUIREMENTS ..................................................................................................................................... 35 RECOMMENDED TOOLS .......................................................................................................................................
Digital PRIORIS XL Server Table of Contents CHAPTER 4 TROUBLESHOOTING............................................................................................................ 71 INITIAL TROUBLESHOOTING ............................................................................................................................... 71 POST AND BOOT MESSAGES .............................................................................................................................. 72 BEEP CODES ..........
Digital PRIORIS XL Server Table of Figures Table of Figures Figure 2 - 1 SCU Main Menu Options .............................................................................................................. 19 Figure 3 - 1 Unlocking and Removing the Side Panel ..................................................................................... 37 Figure 3 - 2 Server Components ........................................................................................................................
Digital PRIORIS XL Server Preface Preface The Digital PRIORIS XL Server Service Maintenance Manual is a troubleshooting guide that can be used for reference when servicing the PRIORIS XL Server series. Digital Equipment Corporation reserves the right to make changes to the Digital PRIORIS XL Server without notice. Accordingly, the diagrams and procedures in this document may not apply to the computer(s) you are servicing since many of the diagnostic tests are designed to test more than one product.
Digital PRIORIS XL Server Chapter 1 Product Description Product description Product Introduction All PRIORIS XL Servers are industry-standard, Intel microprocessor-based servers using a versatile tower enclosure. The server also features several modular CPU board designs that allow for easy server upgrades to the latest available CPU technology. The Intel i486-based CPU module employs an Intel Pentium OverDrive Ready ZIF socket to allow CPU upgrades to future Intel Pentium microprocessor technologies.
Product Description Digital PRIORIS XL Server Product Models Information PRIORIS XL 466d2 Model FDD FR-791WW-A9 1.44MB FR-791WW-XA 1.44MB FR-791WW-XC 1.44MB HDD Memory Cache Options 535MB SCSI-2 8MB 1.05GB SCSI-2 16MB 128KB 128KB 128KB CD-ROM CD-ROM HDD Cache Options 128KB CD-ROM Cache Options 535MB SCSI-2 16MB 1.05GB SCSI-2 16MB 256KB 256KB 256KB CD-ROM CD-ROM HDD Cache Options 1.
Digital PRIORIS XL Server Product Description PRIORIS XL 590DP Model FDD FR-796WW-A9 1.44MB FR-796WW-XC 1.44MB HDD Memory 1.
Digital PRIORIS XL Server Chapter 2 Utilities & Configuration Server Utilities & Configuration Server Utilities The following sections provide detailed instructions on running the MS-DOS utilities contained on the supplied CD-ROM startup diskette and CD-ROM. Note that these utilities can be copied to the hard disk drive. Refer to the operating system documentation for information on copying files. UPGRADE.EXE All servers have BIOS software in a read-only, non-volatile memory (ROM) chip.
Utilities & Configuration Digital PRIORIS XL Server Creating a Recovery Diskette A recovery diskette should always be prepared before attempting to upgrade the BIOS. This diskette contains a BIOS image and a program to load the image into flash memory. If a problem occurs while loading the BIOS into flash memory, a beep sounds when the server is turned on. Insert the recovery diskette into drive A or B and the original BIOS is put back in flash memory.
Digital PRIORIS XL Server Utilities & Configuration Upgrading The Server's BIOS Perform the following steps to update the server's BIOS in the flash memory and compare the BIOS image file to the flash memory: 1) 2) 3) 4) 5) 6) 7) 8) Perform steps 1 through 4 from "Creating a Recovery Diskette." Ιf the BIOS resides on a diskette, you need to use that diskette to upgrade the BIOS. Select the Upgrade Flash from Image File menu option.
Utilities & Configuration Digital PRIORIS XL Server To access SETUP.EXE: 1) 2) 3) 4) 5) 6) 7) 8) Insert the CD-ROM startup diskette into drive A. Boot the server. Allow the POST to complete. If POST detects a configuration error(s), refer to Chapter 4, “Troubleshooting” for possible causes and suggested solutions. Highlight Modify BIOS setup from the main menu, and then press [Enter]. Page 1 of Setup appears. Press the right arrow key to move the cursor to the ROM Based Setup option.
Digital PRIORIS XL Server Utilities & Configuration The SCU The SCU enables you to setup and configure the server using the menu driven items shown in figure 2-1. Depending on the installed hardware and level of server security required, you might have to access one or more of these items to properly configure the server.
Utilities & Configuration Digital PRIORIS XL Server Before Using the SCU When familiar with utility programs and their uses, refer to the appropriate sections in this chapter to setup or update the server’s configuration. Otherwise, carefully read and understand this chapter before attempting to modify the server’s configuration settings. Read any README files contained on the System Configuration Utility diskette for additional information.
Digital PRIORIS XL Server 3) Utilities & Configuration Insert the backup System Configuration Utility diskette into drive A and then soft boot (reset) the server. The SCU introductory screen appears. NOTE The SCU contains help pop-up screens for any selected menu item. Press [F1] at anytime to display a help screen. Press [Esc] to remove a help screen. 4) Press [Enter] to display the SCU Welcome screen. If no configuration errors appear, the Welcome screen displays information about the SCU.
Utilities & Configuration Digital PRIORIS XL Server The SCU automatically detects any EISA expansion boards installed on the server and configures the server accordingly. The SCU does not automatically detect ISA expansion boards. Step 3: View or Edit Details This menu item allows to examine and change the setting of each function and the resource allocated for those functions. When editing a function or resource in this step, you might have to change the switch or jumper setting.
Digital PRIORIS XL Server Utilities & Configuration SCU and Setup Options (continued) Menu Fields Settings Comments System time System date Language Current time Current date English Français Deutsch Italiano Español Nederlands 3.5", 1.44 MB 3.5", 2.88 MB Not Installed 5.25", 360 KB 5.25", 1.2 MB 3.5", 720 KB Drive types 1 through 49 Displays the current time. Displays the current date. Sets the desired language.
Utilities & Configuration Digital PRIORIS XL Server SCU and Setup Options (continued) Menu Fields Settings Comments Video card VGA or EGA CGA 40 Column CGA 80 Column Monochrome Not Installed Enabled at: 3F8h-3FFh (IRQ4) Enabled at: 2F8h-2FFh (IRQ3) Enabled at: 3E8h-3EFh (IRQ4) Enabled at: 2E8h-2EFh (IRQ3) Disabled Enabled at: 2F8h-2FFh (IRQ3) Enabled at: 3E8h-3EFh (IRQ4) Enabled at: 2E8h-2EFh (IRQ3) Disabled Enabled at: 3F8h-3FFh (IRQ4) Enabled Disabled Disabled Enabled Disabled Enabled Enabled Disabl
Digital PRIORIS XL Server Utilities & Configuration SCU and Setup Options (continued) Menu Fields Settings Comments Keyboard Installed Not Installed NumLock at boot Password On Off System only Setup only System and setup Not Installed Enabled Disabled Enables or disables the keyboard when using the server as a network server. Note: You must initially setup the server with a keyboard. Enables or disables the NumLock feature each time the server boots.
Utilities & Configuration Digital PRIORIS XL Server SCU and Setup Options (continued) Fields Settings Comments Large drive addressing Standard The drive’s cylinder/head/sector values are used by the BIOS and operating system. Allows the server’s BIOS to convert the logical cylinder/head/sector used by the operating system to the drive’s cylinder/ head/ sector value. Enables or disables drive A as the logical boot device.
Digital PRIORIS XL Server Utilities & Configuration SCU and Setup Options (continued) Fields Settings Comments AT bus space Disabled Memory hole not available. Upper memory is contiguous. F00000h, 1MB Sets the memory hole at address F00000 with 1 MB memory available. E00000h, 1MB Sets the memory hole at address E00000 with 1 MB memory E00000h, 2MB available. C00000h, 4MB Sets the memory hole at address E00000 with 2 MB memory available.
Utilities & Configuration Digital PRIORIS XL Server SCU and Setup Options (continued) Fields Settings Comments PCI arbiter System default Use system default according to host/EISA bridge used. priority(7) The priority rotates for all PCI devices. Pure rotating EISA bridge has highest priority. EISA slot Onboard SCSI has highest priority. External onboard SCSI Onboard SCSI CPU has highest priority. CPU PCI slot 3 has highest priority. PCI slot 3 PCI slot 2 has highest priority.
Digital PRIORIS XL Server Utilities & Configuration SCU and Setup Options (continued) Fields Settings Comments PCI device(8) Enable device: Enabled Disabled Allows to individually enable or disable each PCI slot and onboard SCSI.
Utilities & Configuration Digital PRIORIS XL Server ROM Based Setup This option is often used by educational facilities that have public access to their servers. Disabling this option prevents unauthorized personnel from changing any server’s configuration parameters. Parallel Port and Serial Ports The server logically assigns LPTx and COMx names to: ♦ ♦ Parallel ports in the address order 378h and 278h. Serial ports in the address order 3F8h, 2F8h, 3E8h, and 2E8h. This occurs during each boot process.
Digital PRIORIS XL Server Utilities & Configuration CPU Speed This option determines the speed used by the server each time you turn it on or reboot it: ♦ ♦ Fastis the normal speed and causes the CPU to run at its rated speed. Slow(equivalent to 8 MHz) is used to reduce the effective CPU speed to be compatible with some speeddependent application programs. If an application program does not run correctly at full speed, try disabling all caches or changing the CPU speed to slow.
Utilities & Configuration Digital PRIORIS XL Server Cache BIOS ROM This option allows the server’s BIOS to be cached in the primary cache and secondary cache (if installed). This increases server performance because BIOS instructions are fetched from cache instead of RAM. Shadow Video ROM The main logic board reserves an area of DRAM for a copy of video BIOS ROM. This DRAM (called "shadow memory") is write-protected and has the same addresses as the video BIOS ROM locations.
Digital PRIORIS XL Server Utilities & Configuration PCI Device This option allows to configure the PCI slots on the server’s main logic board when adding PCI expansion boards. CAUTION The PCI Device selections for factory installed PCI expansion boards should stay at the factory default settings. Modifications can cause server failure.
Digital PRIORIS XL Server Chapter 3 Service Procedures Service Procedures Safety Requirements WARNING Static electricity collects on non-conductors such as paper, cloth, or plastic. A static discharge can be damaging even though you often cannot see or feel it.
Service Procedures Digital PRIORIS XL Server Recommended Tools The following tools will be needed for servicing Digital PC systems. Note that test equipment must be calibrated: ♦ ♦ ♦ Multimeter (4 1/2 digit) A philips screwdriver An antistatic wrist strap Other Needed Materials Cleaning agent should be an all purpose cleaner that is used in-house. Required Special Tools None. Remedial Diagnostic Test Software ♦ P R I O R I S X L QAPLUS/fe , PC Advanced Diagnostic Software, latest version.
Digital PRIORIS XL Server Service Procedures Removing the Side Panel Before removing the side panel, perform the following: 1) 2) 3) 4) Turn off power to all external devices connected to server. Turn server off. Unplug power cord from wall outlet. Disconnect power cord and monitor cord from server. WARNING You might injure yourself or damage the server when attempting to remove the side panel before unplugging the ac and monitor power cords.
Service Procedures Digital PRIORIS XL Server Server Components Legend Component A B Power supply 5 EISA and 2 PCI 32-bit local bus expansion slots or 4 EISA and 3 PCI 32-bit local bus expansion slots CPU module Main logic board 3½-inch diskette drive (or internal device in place of) Front access 5¼-inch half-height drive bays Internal 3½-inch drive bays C D E F G F A D P R I O R I S C B E X L G DEC00242-2 Figure 3 - 2 Server Components 38 MCS Logistics Engineering - Nijmegen
Digital PRIORIS XL Server Service Procedures Expansion Slots The PRIORIS XL Server contains eight slots for installing up to seven EISA or PCI expansion boards. Five of the slots support industry-standard 32-bit EISA expansion boards. The remaining three expansion slots support 32-bit PCI local bus expansion boards. This enables the server to deliver maximum performance by using a faster data path for greater computing speed. It also improves the expandability of the server.
Service Procedures Digital PRIORIS XL Server Main Logic Board Jumpers Jumper pins allow to set specific server parameters. They are set by changing the pin location of jumper blocks. A jumper block is a small plastic-encased conductor (shorting plug) that slips over the pins. To change a jumper setting, remove the jumper from its current location with the fingers. Place the jumper over the two pins designated for the desired setting. Press the jumper evenly onto the pins. Be careful not to bend the pins.
Digital PRIORIS XL Server Service Procedures Main Logic Board Jumper Locations J24 1 2 3 J22 J25 J27 P R I O R I S J38 J39 J17 J9 J37 J50 X L J41 DEC00230-2 Figure 3 - 4 Main Logic Board Jumper Locations MCS Logistics Engineering - Nijmegen 41
Service Procedures Digital PRIORIS XL Server Computer Memory Configurations Adding more memory allows the server to run larger, more complicated software and run it quicker. The amount of memory the server supports depends on the installed type of CPU module. ♦ ♦ When the i486 PCI Series CPU module is installed, the server will support up to 128 MB using SIMM banks 0 through 3. When the Pentium 560/566 CPU module is installed, the server will support up to 256 MB using SIMM banks 0 through 5.
Digital PRIORIS XL Server Service Procedures PRIORIS XL466 and 4100 Memory Configurations ♦ ♦ ♦ Standard configuration of 8 MB Maximum 128 MB Only the configurations listed below are allowed.
Service Procedures Digital PRIORIS XL Server PRIORIS XL560, 566 and 590 Memory Configurations (continued) P R I O R I S X L Bank 0 / 1 Bank 2 / 3 2 x 4 MB 2 x 8 MB 2 x 8 MB 2 x 4 MB 2 x 4 MB 2 x 8 MB 2 x 16 MB 2 x 16 MB (ECC) 2 x 32 MB 2 x 32 MB (ECC) 2 x 4 MB 2 x 4 MB 2 x 4 MB 2 x 8 MB 2 x 8 MB 2 x 4 MB 2 x 8 MB 2 x 16 MB 2 x 16 MB (ECC) 2 x 16 MB 2 x 16 MB (ECC) 2 x 4 MB 2 x 8 MB 2 x 32 MB 2 x 16 MB (ECC) 2 x 16 MB 2 x 32 MB (ECC) 2 x 4 MB 2 x 8 MB 2 x 16 MB 2 x 16 MB (ECC) 2 x32 MB 2 x 32 MB (ECC)
Digital PRIORIS XL Server Service Procedures Part Removal and Replacement Removing the 3½-Inch Diskette Drive To remove the 3½-inch diskette drive: 1) 2) 3) 4) 5) 6) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Disconnect power and ribbon cables. Remove two screws securing drive to chassis. Slide drive forward out of server.
Service Procedures Digital PRIORIS XL Server Removing a 5¼-Inch Device (Front Access Drive Bay) To remove a 5¼-inch device from one of the front access drive bays: 1) 2) 3) 4) 5) 6) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Disconnect power and ribbon cables. Remove two screws securing device to chassis. Slide 5¼-inch device forward out of drive bay.
Digital PRIORIS XL Server Service Procedures Removing a 3½-Inch Mass Storage Device (Internal Drive Bay) To remove a 3½-inch mass storage device from the internal drive bay: 1) 2) 3) 4) 5) 6) 7) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Disconnect power and ribbon cables. Remove mounting screws. Pull drive from internal drive bay. Remove expansion brackets.
Service Procedures Digital PRIORIS XL Server Removing Fan Pipe To remove the fan pipe: 1) 2) 3) 4) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Unhook plastic fan pipe from lower fan assembly and remove.
Digital PRIORIS XL Server Service Procedures Removing Upper Fan Assembly To remove the upper fan assembly: 1) 2) 3) 4) 5) 6) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Remove fan connection from main logic board. Press in on retaining clips. Tilt assembly away from front panel and remove.
Service Procedures Digital PRIORIS XL Server Removing Fan/Speaker Assembly To remove the fan/speaker assembly: 1) 2) 3) 4) 5) 6) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Remove fan and speaker connections from main logic board. Press down on the two retaining clips. Tilt assembly away from front panel and remove.
Digital PRIORIS XL Server Service Procedures Removing Main Logic Board To remove the main logic board: 1) 2) 3) 4) 5) 6) 7) 8) 9) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Remove all connectors. Remove CPU module retaining bracket and CPU module. Remove all expansion boards. Remove upper fan, fan pipe, and fan/speaker assembly. Remove mounting screws.
Service Procedures Digital PRIORIS XL Server Removing Power Supply To remove the power supply: 1. 2. 3. 4. 5. 6. 7. 8. Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Disconnect power cord. Pull off Power On/Off button from switch at front panel. Remove two screws securing On/Off switch to chassis. Remove four screws securing power supply to rear panel. Remove power supply from server.
Digital PRIORIS XL Server Service Procedures Removing CPU Module CAUTION Before installing a new CPU module, update the server BIOS. Do not wait to update the BIOS until after installing a new CPU module. 1) 2) 3) 4) 5) Turn off external devices and server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Remove CPU module retaining bracket. Carefully remove CPU module from main logic board.
Service Procedures Digital PRIORIS XL Server Installation Procedures Installing Additional Secondary Cache Memory (i486 CPU Modules) The CPU module is equipped with 128 KB direct-mapped adaptive write-back secondary cache memory. This secondary cache memory is designed to improve the performance of the installed CPU. An additional 128 KB cache memory option is available to increase secondary cache memory to 256 KB. This kit consists of four 32 KB × 8 SRAM chips installed in DIP sockets on the CPU module.
Digital PRIORIS XL Server 7) 8) Service Procedures Set all appropriate cache jumpers. Install and secure the CPU module to the main logic board.
Service Procedures Digital PRIORIS XL Server Installing Video Memory The server comes standard with 512 KB of video memory. this amount can be increased to 1 MB by installing a 512 KB video memory DRAM chip in the designated socket on the main logic board. To install the video memory upgrade chip, perform the following: 1) 2) 3) 4) 5) 6) 7) Turn off the server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Install video memory DRAM chip.
Digital PRIORIS XL Server Service Procedures Upgrading Procedures Upgrading the CPU Module Installing a higher-performance CPU module increases the capabilities of the server. It also allows to upgrade with future CPUs as technology becomes more advanced. To upgrade the CPU module: 1) 2) 3) 4) 5) 6) 7) If necessary, update the computer's BIOS. Remove the CPU module's retaining bracket. Grasping both ends of the CPU module, carefully remove it from the main logic board.
Service Procedures Digital PRIORIS XL Server Upgrading the i486 CPU module The CPU module is equipped with a Pentium OverDrive Ready ZIF socket. The socket is capable of supporting faster i486 CPUs and OverDrive CPUs (including future 3.3 V dc CPU technology). To install a higher performance CPU: 1) 2) 3) 4) Remove the CPU module. Place the CPU module on an anti-static surface. Lift up on the lever to release the CPU. Remove the CPU noting its pin 1 location.
Digital PRIORIS XL Server Service Procedures i486 CPU Module Jumper Settings Figure 3- 21 shows the CPU module’s jumper location as well as secondary cache memory upgrade sockets. (Figure 3 - 21, A). The following table lists the factory default settings. If necessary, refer to Chapter 5 “Device Mapping” for memory mapping information.
Service Procedures Digital PRIORIS XL Server Upgrading the 560 / 566 CPU module. The 560/566 CPU module is equipped with a ZIF socket (Socket 4 type) capable of supporting Intel OverDrive CPUs. To install a higher performance CPU: 1) 2) 3) 4) 5) 6) 7) 8) Remove the CPU module. Place the CPU module on an anti-static surface. Lift up on the release lever to release the CPU. Remove the CPU, noting its pin 1 orientation. Install the new CPU. Make sure pin 1 on the CPU is aligned with pin 1 on the ZIF socket.
Digital PRIORIS XL Server Service Procedures 560/566 CPU Module Jumper Settings Figure 3 - 24 shows the CPU module’s jumper location. The following table lists the factory default settings. If necessary, refer to Chapter 5 “Device Mapping”, for memory mapping information.
Service Procedures Digital PRIORIS XL Server Upgrading the 590 CPU module The CPU module might be equipped with a 90MHz Pentium processor installed in a CPU ZIF socket (socket 5 type). A second CPU ZIF socket is available for future Pentium OverDrive processors. The Pentium processor(s) and related high-performance caching circuitry are located on a CPU module connected to the main logic board inside the computer.
Digital PRIORIS XL Server Service Procedures 590 CPU Module Jumper Settings Figure 3 - 26 shows the jumper pin locations as well as the location of the CPU module's secondary cache memory upgrade socket (A, Figure 3 - 26). The following table lists the factory default settings. If necessary, refer to “Device Mapping” for memory mapping information.
Service Procedures Digital PRIORIS XL Server Upgrading Secondary Cache Memory The Pentium CPU module comes with standard or burst secondary cache memory in the form of a single in-line cache module. Secondary cache memory is designed to greatly improve the performance of the installed CPU(s). Note that “standard” cache refers to asynchronous cache and “burst” cache to synchronous (higher performance) cache.
Digital PRIORIS XL Server Service Procedures Replacement Procedures Replacing the Server Battery/Real Time Clock (RTC) The server's battery runs the server clock and retains any setup information when it is turned off. To replace the battery, perform the following: 1) 2) 3) 4) 5) 6) 7) 8) 9) Record server configuration settings. Turn off the server. Disconnect external devices, ac power, and monitor power. Unlock and remove side panel. Remove battery. Install new battery. Replace and lock side panel.
Service Procedures Digital PRIORIS XL Server Connecting Procedures Connecting Diskette and IDE Devices To connect diskette and IDE devices, perform the following: 1) 2) P R I O R I S Connect supplied ribbon cable to appropriate device as shown. Make sure cable is connected with correct orientation. Most cables and sockets are keyed so they cannot be connected backwards. If the cable or device is not keyed, you must connect pin 1 of cable to pin 1 of device's socket.
Digital PRIORIS XL Server Service Procedures SCSI Configuration Guidelines The PRIORIS XL Server includes an onboard Adaptec AIC-7870 SCSI controller. The AIC-7870 connects directly to the PCI local bus and supports up to seven SCSI devices installed within the server enclosure. Additional SCSI devices can be added to the server by using an EISA- or PCI-based SCSI controller installed in an available expansion slot in conjunction with an external SCSI expansion box.
Service Procedures Digital PRIORIS XL Server Connecting SCSI Devices To connect SCSI devices, perform the following: 1) 2) 3) Connect supplied ribbon cable to appropriate device as shown. Make sure cable is connected with correct orientation. Most cables and sockets are keyed so they cannot be connected backwards. If the cable or device is not keyed, you must connect pin 1 of cable to pin 1 of device's socket. Pin 1 of cable is on edge with colored stripe.
Digital PRIORIS XL Server Service Procedures Connecting an External SCSI Bus You can use the wide (68-pin) or narrow (50-pin) SCSI connector on the main logic board to connect external SCSI devices to the server. NOTE The External Onboard SCSI field in the BIOS Setup must be set to Enabled. To connect an external SCSI bus, follow these instructions: 1) 2) 3) 4) 5) 6) 7) 8) Connect the 68-pin or 50-pin cable connector to the corresponding connector on the main logic board.
Service Procedures Digital PRIORIS XL Server External SCSI Bus Guidelines 1) 2) 3) 4) Make sure that the selected SCSI addresses for the external SCSI devices do not conflict with other devices in the server. Make sure that the external SCSI bus is terminated properly. For proper operation, the length of the SCSI cable must not exceed 1 meter (3.28 ft). Use only a high-density external connector.
Digital PRIORIS XL Server Chapter 4 Troubleshooting Troubleshooting The following pages provide initial troubleshooting procedures and tables listing specific problems, probable causes, and recommended actions to take if the computer fails after it has been configured or after installing optional hardware or software. Refer to the documentation supplied with additional options when experiencing problems with specific installed options.
Digital PRIORIS XL Server Troubleshooting POST and Boot Messages The POST displays messages to alert to errors in hardware, software, and firmware or to provide operating information about the computer. Each time the POST displays a message on the screen, the computer's speaker beeps twice. If an error occurs before the monitor is initialized, specific beep codes sound to alert to a problem. The table below lists a general grouping of system messages arranged by the POST countdown number.
Digital PRIORIS XL Server Troubleshooting POST and Boot Messages (continued) POST Countdown Number Message Number Message Solution 080 0016 Hard disk 0 failure 060 0021 xxxx0h optional ROM bad checksum = xx 050 0019 Time-of-day not set 040 020 010 000 0020 — — — Keyboard is locked Enable NMI Enable cache Boot Run the SCU. Check all connections. If the problem persists, replace the hard disk. Correct the address conflict. If the problem persists, replace the ROM chip. .
Digital PRIORIS XL Server Troubleshooting Beep Codes for fatal Errors (continued) P R I O R I S X L Beep Code Error Message 2-1-1 2-1-2 2-1-3 2-1-4 2-2-1 2-2-2 2-2-3 2-2-4 2-3-1 2-3-2 2-3-3 2-3-4 2-4-1 2-4-2 2-4-3 2-4-4 3-1-1 3-1-2 3-1-3 3-1-4 3-2-1 3-2-3 3-2-4 4-2-1 4-2-2 4-2-3 4-2-4 4-3-1 Bit 0 1st 64 KB RAM failure Bit 1 1st 64 KB RAM failure Bit 2 1st 64 KB RAM failure Bit 3 1st 64 KB RAM failure Bit 4 1st 64 KB RAM failure Bit 5 1st 64 KB RAM failure Bit 6 1st 64 KB RAM failure Bit 7 1st 64 KB R
Digital PRIORIS XL Server Troubleshooting Beep Codes for Nonfatal Errors The table below lists the beep codes when it encounters a nonfatal error. This table lists nonfatal errors that do not lock up the computer. Fatal errors that lock up the computer are listed in a separate table.
Digital PRIORIS XL Server Troubleshooting Server Troubleshooting (continued) P R I O R I S X L Problem Possible Cause Action Server operates incorrectly after installing optional system memory (SIMMs) Server does not boot from an IDE hard disk drive SIMMs have failed. Replace SIMMs. Operating system soft-ware is not installed on the IDE hard disk drive. Install the appropriate operating system. IDE hard disk drive is not correctly formatted or requested partition does not exist.
Digital PRIORIS XL Server Troubleshooting Server Troubleshooting (continued) Problem Possible Cause Action Server does not recognize an external SCSI device SCSI device jumpers incorrectly set. Refer to the supplied kit installation instructions. Server does not boot from an internal SCSI hard disk drive Refer to the supplied kit installation instructions. SCSI ID conflicts. Remove terminating resistors. Refer to the supplied kit installation instructions.
Digital PRIORIS XL Server Troubleshooting Server Troubleshooting (continued) Problem Possible Cause Action No response to mouse commands Mouse is password protected. Enter the keyboard and mouse password. Mouse is connected to the keyboard port. Power down the server and connect the mouse to the mouse port. Mouse driver not installed. Install the appropriate mouse driver. Refer to the supplied application software documentation. Refer to the application software documentation.
Digital PRIORIS XL Server Troubleshooting Monitor Troubleshooting Problem Possible Cause Action Monitor power indicator is not on. No screen display. Monitor is turned off. Turn on the monitor. Power indicator is defective. Configuration error Replace Monitor (power indicator). Run the SCU to configure the server for VGA operation. Set the jumper for VGA operation. Monitor brightness and contrast controls are incorrectly set. Monitor type incorrectly set.
Digital PRIORIS XL Server Troubleshooting QAPlus/FE Error Messages Component Messages Solution CPU Arithmetic Function Failed General Functions Failed Exception Interrupt in Protected Mode Refresh Failure Logic Functions Failed Butterfly Cylinder Access Test Failed Cylinder 0 Errors Random Cylinder Access Failed Linear Cylinder Access Failed Controller Diagnostic Test Failed Reset CPU Replace CPU Questionable Controller Card Reset controller, Replace controller, Hard drives failed Media Mismatch
Digital PRIORIS XL Server Device Mapping Chapter 5 Device Mapping This section provides a series of tables listing mapping and address information related to computer memory and various main logic board devices (keyboard controller, interrupt controller, DMA controller, etc.). The computer's memory and address locations are allocated at the factory to operate within a standard PC environment.
Device Mapping Digital PRIORIS XL Server CPU Memory Address Map (Full Range, 560/566 CPUs) Range Function Notes 0 KB to 512 KB 512 KB to 1024 KB Main memory Main memory 1 MB to 16 MB Main memory Memory space gap PC compatibility range PC compatibility range (EISA/ISA memory lower limit) EISA/ISA memory upper limit PCI memory hole (16 MB max. size)(2) 16 MB to 192 MB(1) 192 MB to 4 GB(1) Main memory Pentium processor upper limit PCI memory (1) 128 MB max. for DECpc LPx 560/566 (1) 512 MB max.
Digital PRIORIS XL Server Device Mapping CPU Memory Address Map (PC Compatibility Range) Address Range Function Size 0000 to 7FFFF 80000 to 9FFFF A0000 to BFFFF Main memory Main/PCI/ISA memory PCI/ISA video buffer memory Video memory BIOS PCI/ISA card BIOS and buffer memory ISA/PCI adapter RAM after POST Used by BIOS Setup during POST SCSI BIOS (if enabled) Planar BIOS memory 512 KB 128 KB 128 KB C0000 to C7FFF C8000 to DFFFF E0000 to EBFFF EC000 to EFFFF F0000 to FFFFF (1) 32 KB 96 KB 64 KB (48 K
Device Mapping Digital PRIORIS XL Server Computer Interrupt Levels Interrupt Number Interrupt Source IRQ1 IRQ3 IRQ4 IRQ6 IRQ7 IRQ12 IRQ13 IRQ14 Keyboard controller COM2 (if enabled) COM1 (if enabled) Diskette drive (if enabled) LPT1, LPT2, LPT3 (if enabled) Mouse interrupt Math co-processor Hard disk drive (if enabled) DMA Channel Assignment P R I O R I S X L Channel Controller Function 0 1 2 3 4 5 6 7 1 1 1 1 2 2 2 2 Refresh Not used Diskette controller (if enabled) Not used Cascade DMA Not us
Digital PRIORIS XL Server Chapter 6 Pass / Fail Criteria Pass / Fail Criteria As Final Acceptance Test the following tests should be run to meet the Pass/Fail criteria: As Final Acceptance Test’ the following tests should be run to meet the Pass/Fail criteria: 1) Successful completion of the POST tests.
Digital PRIORIS XL Server Appendix A Service Notes Service Notes This appendix contains the current Service Notes for the PRIORIS XL product line. Known Server limitations. ♦ ♦ ♦ ♦ Do not install a 5¼-inch diskette drive in the top drive bay. EMI shielding might cause elecrical shorts to the etch on the diskette drive’s circuit board. Due to the length of the IDE cable, make sure IDE drives are installed in drive bay slots 1 and 2. Otherwise, the IDE cable will not reach the IDE drive’s connector.
Device Mapping Digital PRIORIS XL Server Remedial Diagnostic Test Software. ♦ QAPLUS/fe , PC Advanced Diagnostic Software, latest version. Partnumber : 22-00908-06 Recommended Virus Detection and Cleanup Software ♦ F-PROT, Virus Detection and Cleanup Software, latest version. Network locations: North America, South America, Australia and New Zealand: MINOTR::USER6:[VIRUS.F-PROT} Europe, Africa, Middle and Far East: VARDAF::EUROPUB:[VIRUS_SCANNER.F-PROT] ECO/FCO Information. BIOS version information.
Digital PRIORIS XL Server Useful Information Appendix B Useful Information Related documentation Order Number Description. K-MN-PRIORIS-XL-JG01 ER-791WW-IA ER-791WW-UA ER-78XWW-CA PRIORIS XL Quick Reference Guide PRIORIS XL Server Quick Setup Guide PRIORIS XL Server User’s Guide Pentium CPU Modules On-Line Bulletin Boards The most current product information and technical support is also available on line.
Digital PRIORIS XL Server Document Feedback Document Feedback If you have comments on the contents or layout of this document we highly appreciate you feedback. We will do our best to make this document a valuable support to your service effort for Digital. Please fill -out the reader feedback form and send or fax it to: Digital Equipment Parts Center b.v. Att: MCS Logistics Engineering Call Desk P.O.