User Guide

Amp Footswitch
From the factory,the Amp Footswitch changes between the Green and the Red Amp Channels. However,the GNX1
allows you to select the function of the Amp Footswitch.The procedure for assigning the function of the Amp
Footswitch is as follows:
1.Press the Effect Select button until the Exp Assign row has been selected.
2.Press the Status button until the Display reads AMP FS (Amp Footswitch).
3.Rotate the Number 1 Knob to select the desired function of the Amp Footswitch.Your choices include:
G-R - Switches between the Green and Red Amp Channels.
G-Y - Switches between the Green and Yellow (Warped) Channels.
R-Y - Switches between the Red and Yellow (Warped) Channels.
G-R-Y - Switches between the Green,Red,and Yellow (Warped) Channels.
4.Store your Amp Footswitch assignment to your Preset.See page 17 for more information on the storing procedure.
Expression Parameter Assignment List
The following Parameters can be assigned to the any of the 3 Expression Pedal links, LFO 1, or LFO 2.
NOLINK (No Link) - No Parameter is assigned
VOLPRE (Volume Pre) - Controls the Volume after the Amp Modeling but before the Effects.
VOLPST (Volume Post) - Controls the Volume at the end of the Effects chain.
A WARP (Amp Warp) - Warps the Green and Red Amp Models.
C WARP (Cabinet Warp) - Warps the Green and Red Cabinet types.
WARP (Warp) - Warps the Green and Red Channels.
CMPATK (Compressor Attack) - Controls the Compressor’s Attack time.
CMPRTO (Compressor Ratio) - Controls the Compressor’s Ratio.
CMPTHR (Compressor Threshold) - Controls the Compressor’s Threshold.
CMPGAN (Compressor Gain) - Controls the Compressor’s Gain.
AMOUNT/SHIFT (Parameter 1) - Controls the interval for the IPS module.
WHMPDL (Whammy™ Parameter 2) - Controls the pitch bend when Whammy™ is engaged.
SCALE (IPS Parameter 2) - Controls the scale when the IPS module is engaged.
KEY (IPS Parameter 3) - Controls the key type when the IPS module is engaged.
IPSMIX/IPSLVL (IPS Mix/Level) - Controls the wet/dry mix or Level for the IPS module.
AMPCHN (Amp Channel) - Switches Amp Channels.
G GAIN (Green Gain) - Controls the Amp Gain for the Green Channel.
G LEVL (Green Level) - Controls the Volume of the Green Channel.
R GAIN (Red Gain) - Controls the Amp Gain for the Red Channel.
R LEVL (Red Level) - Controls the Volume of the Red Channel.
GATTHR (Gate Threshold) - Controls the Noise Gate’s Threshold.
GATATK (Gate Attack) - Controls the Noise Gate’s Attack time.
PLKSNS (Gate Pluck) - Controls the Noise Gate’s Pluck Sensitivity.
Modulation Effects Parameters
Active Effect
Chorus SPEED DEPTH PREDLY MODBAL MODLVL
Flanger SPEED DEPTH REGEN MODBAL MODMIX
Phaser SPEED DEPTH REGEN MODBAL MODMIX
Triggered Flanger SPEED SENSTV LFO ST MODMIX
Triggered Phaser SPEED SENSTV LFO ST MODMIX
Tremolo SPEED DEPTH
Panner SPEED DEPTH
Vibrato SPEED DEPTH
Rotary Speaker SPEED DEPTH DOPPLR XOVER MODBAL MODMIX
Auto Ya™ SPEED DEPTH RANGE MODBAL MODMIX
YaYa ™ YA PDL DEPTH RANGE MODBAL MODMIX
SynthTalk ATTACK RELEAS VOX MODBAL SENSTV
33
SECTION FIVE - OTHER FUNCTIONS