JamMan Express XT S t e r e o L o o p e r w /J a m S y n c Owner’s Manual
Warranty We at DigiTech® are very proud of our products and back-up each one we sell with the following warranty: 1. Please register online at digitech.com within ten days of purchase to validate this warranty. This warranty is valid only in the United States. 2. DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
Table of Contents Overview ���������������������������������������������������������������������� 1 Introduction ��������������������������������������������������������������������������������1 Features ����������������������������������������������������������������������������������������1 9V Battery Installation ����������������������������������������������� 1 The User Interface & Connectors ����������������������������� 2 The User Interface ����������������������������������������������������������
Overview Introduction The JamMan Express XT is a versatile, yet simple to operate stereo looper. With stereo inputs/outputs, three LEDs to indicate looping status, and true bypass operation, the JamMan Express XT allows you to record mono or stereo loops with ease and without compromising your tone when bypassed.
The User Interface & Connectors The User Interface 1. LOOP LEVEL Knob This knob controls the output level of the loop. 2. Status LEDs These LEDs indicate the status of the pedal as shown in the below table. LED 1 2 Status REC Loop is being recorded. PLAY Loop is playing. DUB Overdub is being recorded. 3 DUB REC DUB PLAY Overdub is being undone/redone. Pedal is in standby (recording/playback stopped). Loop is being cleared (footswitch held).
4 Connectors 2 4. Power Jack Connect an optional PS0913DC power supply to this jack. 9 10 5. JAMSYNC OUT Connect this jack to the JAMSYNC IN jack on another JAMSYNC compatible device for master3control over loop playback and stop functions. 4 6. JAMSYNC IN Connect this jack to the JAMSYNC OUT jack on another JAMSYNC compatible device to slave loop playback and stop functions to a master device. 9 5 5 6 7 7.
Connection Diagrams Standard Looping HARMAN PS0913DC POWER SUPPLY AMP 1 GUITAR IN OUT IN OUT IN OUT IN Out 1 (Mono) In 1 (Mono) Out 2 In 2 IN OUT AMP 2 Optional Multi-Track Looping Using JamSync AMP 1 OUT JAMSYNC IN HARMAN PS0913DC POWER SUPPLIES GUITAR IN OUT IN OUT IN OUT IN OUT IN OUT IN Out 1 (Mono) Out 2 MASTER AMP 2 4 SLAVE OUT In 1 (Mono) In 2 IN JamSync Optional
Multi-Player/Multi-Track Looping Using JamSync HARMAN PS0913DC POWER SUPPLY AMP 1 OUT JAMSYNC IN OUT IN OUT IN OUT IN Out 1 (Mono) Out 2 In 1 (Mono) In 2 IN OUT MASTER GUITAR PLAYER GUITAR AMP 2 HARMAN PS0913DC POWER SUPPLY AMP 1 IN OUT IN JAMSYNC OUT IN OUT Out 1 (Mono) OUT BASS PLAYER BASS In 1 (Mono) IN SLAVE 1 OUTPUT OUT HARMAN PS0913DC POWER SUPPLY IN INPUT IN KEYBOARD OUT IN OUT To PA Mixer (Right) DI 2 OUTPUT OUT OUT OUT IN INPUT IN SLAVE 2 KEYBAORD P
Operation The JamMan Express XT was designed to be very simple to use right out of the box. This section of the manual describes how to perform the basic looping functions. Recording a Phrase The JamMan Express XT records a single phrase and then plays it back as a continuous loop. To record a phrase: 1. Press the FOOTSWITCH and begin playing to start recording. The REC LED will light solid red and recording will begin. 2. When finished recording, press the FOOTSWITCH once to set the loop end point.
Recording Overdubs Once a phrase has been recorded, overdubs can be added on top of the phrase. To record overdubs: 1. Press the FOOTSWITCH to start loop playback. The PLAY LED will light solid green and the phrase will begin playing. 2. Press the FOOTSWITCH again to begin overdub recording. The DUB LED will light solid yellow and audio will be recorded on top of the phrase. 3. When done overdub recording, press the FOOTSWITCH to end the overdub recording session.
Using JamSync Connection & Record Sequence JamSync allows you to synchronize multiple JamSync compatible devices using optional 1/8” mini stereo (TRS) cables (see below cable diagram). This allows a JamSync master to control the loop playback and stop functions for all connected JamSync slaves, providing multi-track 1/8” multiple Stereo Cable (TRS) looping capabilities.
record to the slave and instead wish to record to the slave at a later time in the song. When using this method, you must arm the slave to record before the master device reaches its loop start point. It’s at this loop start point that the master will send the record command to the slave device(s), so the slave device must be armed in advance to receive the record command.
4. Play your part. 5. When finished recording to the slave, press the slave’s FOOTSWITCH once to set the loop end point. The phrase will automatically begin playing back along with the master loop and the PLAY LED will light solid green. 6. Press the FOOTSWITCH on the master device 2 times quickly to stop loop playback on both devices.
Specifications DIGITAL A/D/A Conversion: Max. Individual Loop Time: 24-bit 10 minutes (stereo) LEFT(MONO)/RIGHT INPUTS Connector Type: Input Impedance: Unity Gain Input to Output: Max Input Level at Unity: Left and Right Audio Paths: ¼” Unbalanced (Tip-Sleeve) 550 kΩ Mono/1.
PHONE: (801) 566-8800 WEB: digitech.com SUPPORT: digitech.com/en-US/support JamMan Express XT Owner's Manual 5038282-B © 2015 Harman. All rights reserved. DigiTech is a registered trademark of Harman.
