Supernatural AMBIENT VERB
DECLARATION OF CONFORMITY Manufacturer’s Name: Harman Signal Processing Manufacturer’s Address: 8760 S. Sandy Parkway Sandy, Utah 84070, USA declares that the product: Product name: Supernatural Product option: all (requires Class II power adapter that conforms to the requirements of EN60065, EN60742, or equivalent.
If you want to dispose of this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery, and recycling. Private households in the 25 member states of the EU, in Switzerland and Norway may return their used electronic product free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
WARRANTY: We at DigiTech® are very proud of our products and back-up each one we sell with the following warranty: 1. Please register online at www.digitech.com within ten days of purchase to validate this warranty. This warranty is valid only in the United States. 2. DigiTech warrants this product, when purchased new from an authorized U.S. DigiTech dealer and used solely within the U.S., to be free from defects in materials and workmanship under normal use and service.
Congratulations! You have just purchased a DigiTech® digital effect pedal. Unlike many analog pedals, the number of hours digital pedals can be powered with 9-Volt alkaline batteries is limited due to the constant draw which digital signal processors require. Until battery technology advances to meet the requirements of digital pedals, we suggest that a battery be used mainly for demonstration and practice purposes.
Introduction More than a remarkable achievement, DigiTech’s HardWire® series represents a collection of significant improvements in guitar effects pedals. The HardWire series pedals provide a suite of well-known effects, each with superior tone and control.
Pedal Interface 1 2 3 MIX 4 LIVELINESS D E C AY 11 12 8 5 6 Supernatural AM BIENT VER B 7 8 9 10 2
What Does This Do? 1. Mix Knob - Controls the reverb level. Turn this knob clockwise to increase and counter-clockwise to decrease the reverb level. 2. DC Adapter Jack - Connect the optional power supply to this jack. Use the proper supply for your area’s mains line voltage. 3. Liveliness Knob - Controls the amount of high frequency response in the Reverb’s effect signal. Turn this knob clockwise to increase and counter-clockwise to decrease the high frequencies. 4.
supernova - Deep space reverb with twisting flange and pitch shifting. • shine - Shimmer reverb with a thick lush chorus added. • pherb - Rich Lexicon Hall reverb with a hint of phasing. • spring - The unmistakable classic ‘surf’ reverb. 6. Input 1 (Mono) - Connect your instrument, the output of a pedal, or an amp effects send to this jack. Signals are heard at both outputs when only the Input 1 (Mono) jack is used. This jack enables battery power to the pedal when connected.
8. Foot Switch Release Pins - These two pins are spring loaded hinges that hold the Foot Switch in place. See page 10 for information on accessing and changing the battery. See page 6 for more information about using and changing the Tails Switch settings. 9. Indicator LED - Lights when the effect is turned on. When battery power is low (approximately 15 minutes), the Indicator LED begins to dim giving you advanced warning that very shortly you will need to replace the battery. 10.
Tails Switch The Supernatural features a switch that allows the reverb signal to continue being heard after the effect is bypassed. When the Tails Switch is set ON, the Supernatural does not utilize true hardwire bypass. If you always want to use true hardwire bypass, set the Tails Switch to OFF. When the Tails Switch is OFF, reverb signal is cut off immediately when the effect is bypassed.
7
Amplifier Setup Optional Power Supply MIX LIVELINESS D E C AY Supernatural A M B I E NT 8 V E R B or
Effects Setup AMP RETURN Optional Power Supply MIX LIVELINESS AMP SEND D E C AY Supernatural A MB IE NT VE RB Note: If the amp effects loop has a mix control, set the mix to 100% full wet.
Battery Operation 10 In the event that battery power is completely depleted, HardWire pedals automatically switch into bypass. This eliminates the need to remove the pedal from your pedal chain if the battery is dead. To replace the battery, do the following: 1. Using the tip of a 1/4” guitar cable, push one of the Release Pins in on either side of the Foot Switch, and remove it from the pedal chassis. 2. Remove the battery from the battery compartment and disconnect the battery cable. 3.
into place over the depressed pin. Release the pin. When the Foot Switch is properly fastened, both release pins are flush with the outer side of Foot Switch the pedal.
Performance Accessories The performance accessories make integrating a HardWire pedal into any pedal board a snap.
Hook-and-loop Pedalboard Pad To attach the Pedalboard Pad, do the following: 1. Peel off the existing rubber skid pad from the bottom of the pedal. 2. Peel the adhesive protector from the back of the Pedalboard Pad. 3. Apply the Pedalboard Pad to the bottom of the pedal.
Foot Switch Glow Sticker To attach the Foot Switch Glow Sticker, do the following: 1. Peel the adhesive backing from the Foot Switch Glow Sticker. 2. Apply the Glow Sticker to the top of the Foot Switch.
StompLock To place the StompLock over the pedal knobs, do the following: 1. Set the knobs to your preferred setting. 2. Gently push the StompLock over the top of the knobs. 3. To remove the StompLock, gently lift one side and then the other.
Specifications Controls: Level, Liveliness, Decay, Type, On/Off Pedal Jacks: Input 1 (Mono), Input 2, Output 1 (Mono), Output 2 Input Impedance: >1 MΩ (stereo), >500 kΩ (mono) - effect on Output Impedance: 1 kΩ - effect on Input Impedance: True hardwire bypass - effect off Output Impedance: True hardwire bypass - effect off Power Supply: 9 V Alkaline Dry Battery or Harman 9 VDC power supply Current Draw: 75 mA (typical at 9 VDC) Power Consumption: 675 mW (typical w/optional power supply) D
8760 South Sandy Parkway Sandy, Utah 84070 PH (801) 566-8800 FAX (801) 566-7005 DigiTech® and HardWire® are registered trademarks of Harman Designed in the USA Copyright - Harman Printed in China HardWire® Supernatural Owners Manual 5020843-B Please visit our website at: www.digitech.
