Instructions

ManualsBrandsDigitus ManualsComputing & OfficeDigitus DN-13023 Wi-Fi USB multifunction print server 150 Mbps

Multifunction USB Network

Server Series

Quick Installation Guide

DN-13023

 Introduction

This document describes the steps for installing and configuring the

Multifunction USB Network Server as a USB device server in the

Windows environment.

 Package Contents

If any item is missing, please contact the shop where you bought this

product.

- One Multifunction USB Network Server (x1)

- One Quick Installation Guide (x1)

- One Control Center Software CD (x1)

- Power Adaptor (x1) DC IN 12V/2A

 OS Supported

 Windows XP, Windows Vista, Windows 7, Windows 8, Windows 10

 Mac OS X 10.6 Snow Leopard, Mac OS X 10.7 Lion, Mac OS X 10.8

Mountain Lion, Mac OS X 10.9 Mavericks, Mac OS X 10.10 Yosemite,

OS X 10.11 El Capitan

 Physical Description

1. Power Adaptor Connector: for DC IN 12V/2A power adaptor

2. Init Button: for restoring the configurable parameters to the default

values

3. Wireless Station: IEEE 802.11 b/g/n wireless station with antenna

4. Ethernet Connector: connected to a twisted pair category 5 cable

5. USB Host Ports: USB 1.1/2.0 low, full, and Hi-Speed compliant

Summary of content (7 pages)

PAGE 1
Multifunction USB Network Server Series Quick Installation Guide DN-13023  Introduction This document describes the steps for installing and configuring the Multifunction USB Network Server as a USB device server in the Windows environment.  Package Contents If any item is missing, please contact the shop where you bought this product.
PAGE 2
6. Indicators  Power Indicator is lit while power is applied. If it is not lit, or if it blinks, there is a problem with the USB device server or Power Adapter.  LAN Indicator blinks to indicate wired network activity. If it is lit, it indicates the wired network is applied. If it is not lit, it indicates that the server does not connect to the wired network.  WLAN Indicator blinks to indicate wireless network activity. If it is lit, it indicates the wireless network is applied.
PAGE 3
 Install Utility I. Insert the included CD-ROM into the personal computer. The Autorun screen should appear. II. Click Install Product button. III. Click Next, if you see any Next button in installation windows. IV. Click Finish.  Configure Server with Utility Using the Control Center Software (Fig1): 1. Run the Control Center. It will automatically search the existing servers and display their status. Figure 1 Control Center 2. Select the server that you want to configure.
PAGE 4
TCP/IP Setting 5. Set up wireless configuration (only for wireless model): - Set SSID, Channel, and Security according to the table below Infrastructure Mode SSID Must match the Access Point. Channel Access Point sets the Channel used. Wireless stations automatically locate the correct channel. Security Settings Must match the Access Point.
PAGE 5
F. Click the “Connect” button. Then the message “Manually Connect by your_computer_name” will be shown, as Fig5. Figure 5 Device Connected G. Now, the installation program will detect the USB device and continue to install driver. H. After the installation is completed, click the USB device in the Control Center and then click the “Disconnect” button to disconnect the USB device.  Use the USB Device A. In the Control Center, click the USB device server that has the desired USB device attached. B.
PAGE 6
Figure 6 The Disconnect Button  An Example of USB Storage If you connect a USB storage, like Fig 7, your PC will have a new disk. If the USB storage is a flash drive, the new disk is a “removable disk”. Figure 7 The USB Storage You can see the storage icon in the system tray, as Fig8.
PAGE 7
Then just use the new disk as a general disk. After you finish the disk operations, click the storage icon in the system tray and choose “Safely remove USB Mass Storage Device” to remove the USB storage, as Fig9. Figure 9 Removing the USB Storage Then, in the Control Center, click the USB storage device and click the “Disconnect” button to disconnect the USB storage device.  Default Parameters Some of the important default parameters are shown below.