® DIGIUS TFT Console User Manual
INTRODUCTION ........................................................................................................................... 3 FEATURES ................................................................................................................................... 4 PRODUCT TYPE .......................................................................................................................... 5 VIEW OF PRODUCT ............................................................................
INTRODUCTION A KVM control platform integrates a multiple-port KVM switch into a 1U height. It controls multiple PCs from only one platform (keyboard, mouse and monitor). A KVM switch can control 8/16 PCs by direct connection and 256 PCs by 2 level cascade connection. It is easy and quick to install. Just connect the wire to the correct port without software configuration. So, there is no difficulty in installation and incompatibility.
FEATURES Control Platform Control platform with LCD, keyboard, mouse and multiple ports KVM switch 1U height, suitable for 19’’ standard cabinet installation and metal structure 17/19’’ LCD screen with high brightness, high clear and high resolution Control platform can be totally pulled out from the cabinet and the LCD screen can be turned on to 120 degrees Ultra thin keyboard with keypad Mouse touch board with two function button Front panel with lock to prevent damage by accident Built-in
PRODUCT TYPE Type DS-72001GE/US OSD Function No DS-72002GE/US DS-72003GE/US DS-72011GE/US Yes DS-72012GE/US DS-72013GE/US Yes No Note 17 inches LCD screen, keyboard and mouse 17 inches LCD screen, keyboard, mouse and 8/16 ports USB KVM 19 inches LCD screen, keyboard and mouse 19 inches LCD screen, keyboard, mouse and 8/16 ports USB KVM 5
VIEW OF PRODUCT FRONT VIEW 1 2 3 9 4 5 7 6 8 1. Front Panel 2. Handle 3. LCD screen 4. Keyboard 5. Mouse touch board 6. Rear hang ear channel 7. Guide 8. Front hang ear 9.
REAR VIEW 1 2 3 DS-72001GE/US – DS-72011GE/US (1) DC 12V 1000Ma power socket (2) USB keyboard & mouse port (3) PC connecting port DS-72002GE/US – DS-72012GE/US DS-72003GE/US – DS-72013GE/US 1 2 3 (1) DC 12V 1000Ma power socket (2) USB keyboard & mouse port (3) PC connecting port 7
DIMENSION 8
PACKING LIST Type Name Num/Uni t DS-72001GE/US DS-72002GE/US DS-72003GE/US KVM Control Platform 1 DS-72011GE/US DS-72012GE/US DS-72013GE/US KVM Control Platform 1 KVM Connecting Cable Power Cable User Manual 1/8/16 Cable AC Power User Manual 1 1 Note 17 inches LCD screen, keyboard and mouse control platform integrated KVM switch with multiple ports (8/16ports). 19 inches LCD screen, keyboard and mouse control platform integrated KVM switch with multiple ports (8/16ports).
KVM CONTROL PLATFORM CONNECTING WIRE Cable Type USB and PS/2 Connecting Cable KVM Port PC, or Server Port VGA port (Keyboard, mouse and monitor) VGA, Keyboard, Mouse (Standard USB & PS/2 Interface) USB and PS/2 Connecting Cable KVM CONTROL PLATFORM POWER WIRE Wire Type AC Power Wire Note 3 Plugs of National Standard Voltage Range 100~230V Machine Type All AC Power Wire 10
OPERATION CONNECTION OF KVM SIGNAL WIRE Connect the end with 8 sockets to the KVM control platform, and the other one to the computer. Before Use Make sure all the devices are safely grounded Make sure the KVM wire and power wire are connected correctly During Use Pull the KVM control platform out from cabinet totally, the guide locks automatically and the power turns on Release front lock.
Then open the front panel and the LCD can be turn on to 120 degrees. As shown below: AUTO LOCK UNLOCK Press LCD power key (red), the LCD is on After Use Press LCD power key -> the LCD power turns off Close LCD panel and lock the front panel Release guide lock Push the control panel into the cabinet totally, and then the power turns off Hot Plug The KVM control platform supports hot plug. It can be connected and disconnected without turning power off.
Assembling & Disassembling The device can be assembled and disassembled as follows: 13
STANDARD RACK INSTALLATION 1. Screw the front flange to the rack first. Slide the bars with the rear flange towards the rack until the flanges gets contact with the rack, then screw the rear flanges to the rack. 2. Slide the switch onto the support flanges. Use the screws supplied with this package to loosely attach the front of the switch to the front of the rack. 3. Slide the rear attachment sliding brackets along the slide bars until they contact the rear of the switch.
4. Use the screws supplied with this package to attach the bars to the rear of the switch. SINGLE STAGE INSTALLATION To set up your installation, do the following: 1. Plug your USB / PS/2 keyboard, USB / PS/2 mouse and monitor into the console port section located on the unit’s rear panel 2. Using a KVM cable set, plug the DB 15 connector into any available CPU port on the switch 3. At the other end of the cable, plug the keyboard, mouse, video cables into their respective ports on the computer 4.
CASCADE INSTALLATION To set up cascade installation, do the following: 1. Set up single installation as mentioned in SINGLE STAGE INSTALLATION. 2. Connect one end of HDB15 cable to IN port of upper KVM, and the other end to OUT port of lower KVM. This completes the cascade installation, and you can turn on the power to the PCs. NOTE: The LCD KVM switch initially links to PC connected to the first CPU port.
OSD OPERATION OSD OVERVIEW The On Screen Display (OSD) is used to handle all computer control and switching procedures. All procedures start from the OSD main menu. To pop up the main menu, tap the [Scroll Lock] twice. Note: You can optionally change the hotkey to the Ctrl key, in which case you would tap [ctrl] twice. If OSD menu is set as “console locked”, you must input password each time the main menu appears. If no password has been set, just press [Enter] to show main menu.
OSD MAIN SCREEN HEADINGS Heading PN QV PC NAME Explanation This column lists the port numbers for all the CPU ports on the installation. The simplest method to access a particular computer is to move the highlight bar to it, then press [Enter]. If a port has been selected for Quick View scanning, an arrowhead symbol displays in this column to indicate so. The computers that are powered on and are on line have an arrowhead symbol in this column to indicate so.
Many of the OSD functions only operate on the computers that have been selected for listing on the main screen with this function. The choices and their meanings are given in the table below: Choice Meaning ALL Lists all of the ports on the installation. QVIEW Lists only the ports that have been selected as Quick View Ports. POWERED ON Lists only the ports that have their attached computers powered on.
3 SECOND The tip window lasts for 3seconds. ALWAYS ON The tip window always on the screen. Move the highlight bar to an option and press [Enter] to select it. CHANNEL DISPLAY POSITION: Position of the tip window. A small blue window appears on the screen. Use arrow key to move it, then press [Enter] to specify the position. SCAN DURATION: Duration for scanning one port。 Options are 3 seconds, 5 seconds, 10 seconds, 15 seconds, 20 seconds, 30 seconds, 40 seconds, 60 seconds.
SAFETY GUIDE Please follow the directions below when installing, using and maintaining it in order to guarantee the device to work well. When installing and operating the device, please make sure proper power supply first, and then do other operations after it is initialized. As signal and power transfer need custom cable, please use matched cable, unmatched cable may cause system work improperly or even damage the device. Keep airy during operating to prevent high temperature.