Floor / Pallet Scale DWP-1000R DWP-5500R (Floor Scale) DWP-10000R DWP-102E (Indicator) DWP-11KR User Manual A12-51007 V1.
Content CHAPTER 1 MAIN SPECIFICATION CHAPTER 2 INSTALLATION 2.0 SCALE BASE SET UP 2.1 FRONT AND BACK VIEW OF INDICATOR 2.2 KEY FUNCTIONS 2.3 CONNECTING LOAD CELL TO INDICATOR CHAPTER 3 OPERATION 3.1 POWER ON & ZERO SETTING 3.2 MANUAL ZERO SETTING 3.3 TARE 3.4 ACCUMULATING 3.5 COUNTING 3.6 USER FUNCTION STEETING 3.7 CONNECT SCOREBOARD TO INDICATOR 3.
Chapter 1 Main Specification 1. Model: DWP-5500R Floor / Pallet scale 2. Accuracy: Grade Ⅲ, n=5000 3. Sample Rate: 10 times / second 4. Load cell sensitivity 1.5~3mV / V 5. Scale interval: 1/2/5/10/20/50 for option 6. Display: 6 bits LED,6 state indicating signals 7. Power supply: Battery DC6V/4AH 8. Operating temperature/humidity: 0~40℃; ≤90%RH 9.
Chapter 2 Installation 2.0 SCALE BASE SETUP a. Open the scale base box (Box 1) with a knife very carefully. Sharp blade may scratch the scale surface. b.
c. Screw each foot onto the load cell at each corner of the scale base. d. Take out the indicator from Box 2. Plug the scale serial cable into the socket on the back of the indicator. And use a screw driver to tighten the two screws of the plug. e. Plug in power to recharge the battery for 20 hours (recommended). Turn on the indicator by pressing the ON/OFF button on the front of the indicator. Now your scale is ready to use. For advanced operations, please refer to the following pages. 2.
2.3 CONNECTING LOAD CELL TO INDICATOR 1. The 9-pin socket is used to hook up load cell, please refer to graph 2-3. 2. The 4-pin shielded cable is used, and the indicator does not have the function of long distance compensation. 3. Indicator must be reliably connected to Load cell and shielded-cable of load cell must be reliably grounded. 4. Sensor and indicator are static sensitive devices. Soldering operation is prohibited.
3.4 COUNTING FUNCTION (WHEN F3 KEY=1) Sampling: Tare the weight of any container that is used and leave the container on the scale. Place samples on the scale. The quantity of the samples should match the options for the pre-set values: 10, 20, 50, 100 or 200 pieces. Press [MOD] key and the screen will show “P10”, which means the requirement of the sample size. If the sample quantity on the scale is not 10 pieces, press [TARE] key to select the according sample size. Press [FUN] key to confirm.
the high-limit and the low-limit are set as same value, the indicator will set alarm for one key point. If the high-limit is set higher than the low-limit, the indicator will set alarm for a weighing range. To set check-weighing parameters: when the indicator is off, turn it on and press [ZERO] key when the indicator is still warming up. You will see “F1 CLK” on the screen. Press [TARE] key 3 times and the screen will show “F4 CHK”. Press [FUN] key to enter beep mode setting: Beep 1: No beep.
SLP 5: The indicator will enter sleep mode if it is idle for 5 minutes. SLP 10: The indicator will enter sleep mode if it is idle for 10 minutes. Press [FUN] to select and [TARE] to move to the next parameter. 4.3 “F3 KEY” FUNCTION SWITCH Press [FUN] to enter function select. Press [TARE] key to switch among: Key1: Counting, Gross/Net Weight Display Key2: Accumulation & Print Key3: Weight Holding Key4: Pre-tare Function Key5: Animal Weighing 4.4 “F4 CHK” CHECKING WEIGHING SETTING Options: BEEP 1/2/3 4.
Press [FUN] to confirm and go to label format selection. Options: 1/2 “P11 FL”: Weight adjustment for acceleration of gravity change. “P12 KB”: on: keyboard beep is on; off: keyboard beep is off “P13 UT”: Unit Setting. Default unit: lb/kg Lb on/off U1 on/off U2 on/off (Unit 1 or Unit 2 setting) “P14 Pn”: Password Setting. P1: Enter new password Press [FUN] to confirm. P2: Re-enter the new password Press [FUN] to confirm. Screen will show “done”. Chapter 5 Calibration Enter Parameter setting P8.