Bruksanvisning
1 SÄKERHET Säkerhetsföreskrifter Vänligen läs noga igenom den här guiden innan du ansluter din box. För komplett manual besök www.dilog.se. Spara guiden för senare bruk. Placera alltid boxen på ett platt, rent och torrt underlag. Om boxen på något sätt skadas bör den alltid undersökas av en verkstad innan den tas i bruk igen. Tag för vana att alltid dra ur strömmen till boxen om du skall resa bort eller om det är risk för åska. Eventuell rengöring görs med lätt fuktad trasa och mild tvållösning.
• Anslut först kablar till andra enheter, koppla sedan in strömmen till boxen. • Byt ut urladdade batterier till fjärrkontrollen omedelbart efter att de tagit slut och tag ur batterierna om ni inte tänker använda boxen under en tid. 2 SNABBINSTALLATION 1. 2. 3. 4. 5. 6. Kontrollera innehållet Vänligen kontrollera att leveransen är komplett. I förpackningen skall finnas mottagare, fjärrkontroll, batterier samt användarmanual. Inkoppling av mottagaren till TV.
3 Specifikation • Support för SD / HD (MPEG4 AVC/H.
4 Inkoppling av mottagare OBSERVERA: Signal i HD kvalitet levereras inte via RCA-Video. För bästa bild på både SD och HD kanaler skall mottagaren kopplas in med HDMI kabel om det är möjligt. 4.1 Inkoppling av mottagare till en TV a. Koppla in din antennkabel till uttaget märkt “RF IN“ på mottagarens baksida. b. Koppla en HDMI-kabel mellan HDMI-uttaget på din TV och HDMI uttaget på mottagaren. c.
MENU: Med denna knapp öppnar du boxens huvudmeny. EXIT: Med denna knapp går du ur menyer eller ett steg tillbaka i menyträdet. Pil UPP: Med denna knapp går du en kanal upp eller ett steg uppåt i menyn. Pil Vänster: Med denna knapp minskar du volymen. I huvudmenyn navigerar du till vänster. Pil Höger: Med denna knapp ökar du volymen. I huvudmenyn navigerar du till höger. Pil NED: Med denna knapp går du en kanal ned eller ett steg nedåt i menyn. OK/ ENTER: Med denna knapp bekräftar och sparar du val i menyn.
5.3 Bakpanel Nr. Namn Funktion 1 RF IN Antenningång 2 RF OUT Antennutgång för ev. vidarekoppling 3 USB USB 2.0 Port för inkoppling av minne/HDD 4 HDMI High-Definition Digital Video/Audio utgång 5 L Audio ut.
6 TITTA PÅ TV Detta avsnitt beskriver hur du tittar på TV och lyssnar på Radio med mottagaren. Med dagens teknik finns många extra funktioner i utsändningen, till exempel programinformation och flerspråkig textning. 6.1 Vanliga funktioner • Tryck CH+ respektive CH- knapparna för att byta kanal ett steg uppåt respektive nedåt. • Tryck de NUMERISKA knapparna 1-9 för att gå direkt till ett kanalnummer. • Tryck “RECALL” knappen för att visa den kanal du tittade på tidigare.
I TV-läge, tryck “OK” knappen för att öppna kanallistan. Navigera UPP/ NED I listan med PIL UPP/ PIL NED. Använd ‘ / ’ knapparna för att hoppa 10 kanaler upp/ned i listan. bekräfta och gå till markerad kanal med ”OK” knappen. Stäng listan med “EXIT” knappen. Du kan söka efter en kanal på kanalnamn genom att trycka den “BLÅ” knappen på fjärrkontrollen. Skriv de första bokstäverna i kanalnamnet och tryck “GUL” knapp för att komma till sökresultatet i kanallistan. Kanalerna kan grupperas efter typ.
6.2 Option • Textningsspråk (GRÖN knapp): Här kan du välja mellan olika textningsspråk om detta finns tillgängligt I utsändningen, välj med “PIL UPP/ NED”, bekräfta med “OK” knappen. • Ljudspråk (RÖD knapp): Vissa kanaler har flera ljudspår, till exempel olika språk eller flerkanalsljud AC3. Välj med “PIL UPP/ NED”, bekräfta med “OK” knappen. 6.3 EPG (Elektronisk Programguide) Pågående, Nästa och 7 dagars Programinformation EPG startas genom att trycka på “EPG” knappen då du är i vanligt TV läge.
För mer detaljerad information om markerat program, tryck “i” (INFO) knappen. Notera att den information som visas är beroende av programleverantören. Om du vill spela in ett program direkt från EPG, flytta dig till det program du önskar spela in och tryck på “REC” knappen. Programmet läggs nu in i din inspelningslista med alla inställningar och kommer att automatiskt att spelas in under förutsättning att inspelningsbart media t.ex. hårddisk är ansluten, har ledigt utrymme och korrekt installerad.
6.4 EPG-Timer (Timer programming via EPG) I båda EPG lägena finns möjlighet att reservera en eller flera inspelningar på ett mycket enkelt sätt. Navigera bara till det program du önskar spela in och tryck sedan på ”REC” knappen. Ett nytt fönster kommer nu att öppnas som visar den reserverade inspelningen. Om inspelningsbart media t.ex Hårddisk är ansluten kommer programmet att spelas in. Är inspelningsbart media ej anslutet kommer mottagaren att byta till den aktuella kanalen vid tiden för programmet.
6.6 PVR Funktion Om inspelningsbart media är anslutet och fungerande kan mottagaren användas för att spela in TV program PVR (Personal Video Recorder). 6.6.1 Direktinspelning För att starta en direktinspelning av den kanal som är vald, tryck “REC” knappen, välj inspelningstid med VÄNSTER / HÖGER och bekräfta med „OK“ knappen. 6.6.2 EPG Inspelning Enklaste sättet att spela in är via EPG – vänligen se kapitel 6.4 för mer info. 6.6.
6.6.4 Timeshift-Funktion Under “vanligt TV-tittande” finns möjlighet att trycka “PAUSE” knappen för starta mottagarens Timeshift funktion. Detta under förutsättning att inspelningsbart media är anslutet. Mottagaren kommer nu att pausa bilden och du kan ta en promenad med hunden eller hämta en kopp kaffe. För att återuppta tittandet, tryck ”PLAY” knappen. Informationslisten visar hur mycket tidsskillnad det är mellan Timeshift och “live” sändning.
I FIL listan, tryck höger “PIL” för att navigera till MediaExplorer. Under Mediaexplorer finns andra mediafiler om du lagt detta på USB minnet. Välj den fil du vill spela upp och starta genom att trycka på ”OK” knappen. Notera att inte alla typer av filformat stödjs. . Genom att trycka << eller >> knapparna under uppspelning kan du öka uppspelningshastigheten till 2, 4, 8 eller 16x hastigheten både framåt och bakåt. För att stoppa uppspelningen tryck på “STOP” knappen.
7 MENY NAVIGERING Tryck “MENU” knappen för att öppna mottagarens huvudmeny. Huvudmenyn innehåller viktiga funktioner som är indelade i olika kategorier. Varje kategori har sin egen undermeny med ytterligare funktioner. • Redigera kanaler • Installation • Användarinställning • Multimedia • Programkort • System Navigera i huvudmenyn med “PIL upp/ PIL NED”. Gå in i undermenyer genom att trycka ”PIL HÖGER” och bekräfta med ”OK” knappen. Tryck ”EXIT” för att backa ur menyn.
8 Redigera kanaler 8.1 Redigera kanallista I denna meny kan du sortera kanallistan efter eget önskemål. Tryck “MENU” knappen, välj ‘Redigera kanaler” och tryck på “OK” knappen. Följande funktioner finns: Val Knapp Funktion LÅS RÖD Lås och lås upp kanaler (barn lås) Flytta GRÖN Flytta den markerade kanalen till annan plats I kanallistan. Välj GUL Markera kanaler (t.ex.
8.2 Redigera favoritkanaler I denna meny kan du skapa en lista med dina egna favoritkanaler. Du kan skapa upp till 8st favoritlistor. Tryck “MENY”, välj redigera favoritkanaler genom att trycka “HÖGERPIL” och “PIL NEDÅT”, bekräfta med “OK”. Använd “HÖGERPIL och VÄNSTERPIL” för att hoppa mellan listan alla kanaler och favoritkanaler. För att skapa en favoritlista: Stega till den kanal du vill lägga till med ”PIL UPP/ PIL NED” och tryck ”GUL” för att lägga till en eller flera kanaler.
9 INSTALLATION I installationsmenyn har du fyra val: • Automatisk kanalsökning Kabel-TV • Manuell kanalsökning KabelTV • Automatisk kanalsökning marksänt • Manuell kanalsökning marksänt Sökningstyp: Om du vill söka manuellt och vet frekvenserna välj manuell sökning och ställ in rätt frekvens. Vid Automatisk sökning (standard) söks hela frekvensbandet av. Start av sökning oavsett typ görs med ”RÖD” knapp.
10 ANVÄNDARINSTÄLLNINGAR I denna meny finner du inställningar för: - Språkinställning - Tidsinställning - Föräldrakontroll - A/V kontroll - OSD inställning - Automatisk avstängning. 10.1 Språkinställning • Menyspråk: Välj önskat språk för menyer och information. • Primärt/ sekundärt ljudspråk: Vissa kanaler sänder ut 2st ljudströmmar, t.ex. olika språk. Välj det du önskar som första och andra språk.
10.2 Tidsinställning Denna meny innehåller tidsinställning, justering för sommartid och tidszon. Välj “Manuell” eller “Automatisk” läge med vänster eller Höger (PIL), tryck ”OK” för att bekräfta ditt val. I läget auto tar mottagaren tiden ifrån utsändningen och justerar hela tiden så att klockan är korrekt. Vill du manuellt ställa tiden, välj manuell och justera. Inställningen för sommartid kan justeras manuell/ auto. I läget auto hanteras tiden per automatik. 10.
10.4 A/V Kontroll I denna meny kan du justera inställningar för bild och ljud för att passa just din kringutrustning. • TV-Modell: Välj det videoformat som stämmer med din tv modell. • Bildförhållande: Ställ in vilket bildförhållande din TV-apparat har. Välj mellan Auto, 4:3, 16:9. (Tjock-tv = 4:3, Platt-tv = 16:9). • Visa format: Om du väljer formatet 4:3 finns det möjlighet att välja hur mottagaren skall presentera bilden vid en 16:9 formats utsändning.
10.5 OSD inställning I denna undermeny kan du justera visningstiden för informationsrutor t.ex. den som visas då du byter kanal. Du kan även välja vilken grad av transparens/ genomskinlighet du vill att informationsrutorna skall visas med. 10.6 Automatisk avstängning I denna undermeny kan du välja om du vill att mottagaren skall stänga ned sig själv till standby efter en viss tid av inaktivitet.
11 MULTIMEDIA (Kräver tillkopplat och installerat inspelningsmedia) I denna undermeny kan du göra inställningar för ditt tillkopplade inspelningsmedia (Hårddisk eller minne). I menyn finns även möjlighet att formatera. Det finns följande val: • Inspelningslista (Timer) • PVR Inställningar • HDD egenskaper • Fil-lista 11.1 Inspelningslista (Timer) Inspelningstimern har till uppgift att slå på och av mottagaren på de inställda tiderna och samtidigt byta till den kanal som valts.
11.2 PVR Inställningar I denna undermeny kan du välja förvald inspelningstid för direktinspelning (tryck på ”REC” knappen vid ”vanligt tv-tittande”. Vid direktinspelning visas ett fönster som presenterar den förinställda inspelningstiden. Den förinställda inspelningstiden kan justeras. Det lämpligaste alternativet är att välja att mottagaren stänger av inspelningen då det inspelade programmet är slut, mottagaren tar denna info från EPG informationen.
HDD Information visar filsystem, Total storlek, använt och ledigt utrymme på det tillkopplade inspelningsmediet. HDD Speed Ger dig möjlighet att testa så att prestandan på din hårddisk räcker till det du vill använda den till. - SD: spela in SD kanaler - HD: spela in HD kanaler - HD + Tms: spela in HD kanaler och kunna använda Timeshift Formatera: Efter att du bekräftat med “OK” knappen kommer din hårddisk att formateras.
13.1.1 OTA mjukvaruuppgradering Då ny förbättrad mjukvara finns tillgänglig skickas detta ut via TV-nätet. Mottagaren meddelar vid dessa tillfällen om detta och installerar automatiskt den senaste mjukvaran. 13.2 Fabriksinställning I den här menyn finns det möjlighet att radera kanaler för TV/ Radio. Du kan också välja att göra en fabriksåterställning av mottagaren. För att göra en total återställning, välj Fabriksåterställning och ändra till fabriksåterställning längst ut till höger.
USER’S MANUAL
TABLE OF CONTENTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 SAFETY ADVICE............................................................................... 3 QUICK SETUP .................................................................................. 5 FEATURES ....................................................................................... 7 HOW TO CONNECT YOUR RECEIVER............................................. 8 HARDWARE..................................................................................
1 SAFETY ADVICE This product has been manufactured to comply with international safety standards. Please read the following safety precautions carefully. MAIN SUPPLY: 90-260V AC 50/60Hz Operate this product only from the type of power supply indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your local power company. - Disconnect the product from the mains before you start any maintenance or installation procedures.
- Do not place the product on an unstable cart, stand, tripod, bracket, or table where it can fall. A falling product can cause serious injury to a child or adult, and serious damage to the appliance. LIGHTNING, STORM or NOT IN USE: Unplug the product from the wall outlet and disconnect the antenna during a thunderstorm or when left unattended and unused for long periods of time. This will prevent damage to the unit due to lightning and power-surges.
2 QUICK SETUP 1. Check accessories Please check the gift box for completeness of accessories. Included should be: Receiver, Remote Control, external Power Supply, User Manual, 2 Batteries 2. Connect the Receiver to the TV Set Connect your Receiver with your TV Set. Details can be found in the User Manual under chapter 4. How to connect your receiver. Connect the Receiver with the Coaxial Cable Connect your Receiver with Coaxial Cable from your Terrestrial Antenna or Cable connection.
Information about changes to the channel list please see chapter 8. Edit Channels in the User Guide. Under chapter 5.1, you can make yourself familiar with the functions of your remote control. Under chapter 6, the TV, as well as Recording and Playback functions of your receiver are described.
3 FEATURES • Supports SD / HD (MPEG4 AVC/H.
4 HOW TO CONNECT YOUR RECEIVER Please note: HD Signals are not transferred via RCA-Video – For HDTV Signals and also for the best quality on SDTV, please use an HDMI cable where possible. 4.1 Connecting the Receiver to TV a. Connect the coaxial cable from either your Cable connection or your DVB-T Antenna to the connector marked “RF IN” at the rear of the receiver. b. Connect an HDMI-Cable between the HDMI-ports of your TV Set and your Receiver. c.
5 HARDWARE 5.1 Remote Control POWER. By pressing this button, the receiver will go into standby mode. When the receiver is in standby mode, it can be awakened by pressing this button again. MUTE. By pressing this button, all audio outputs of the receiver are muted. When muted, Audio output can be regained by pressing this button again. RED / AUDIO: By pressing this button you can choose alternative Audio tracks if provided by the channel operator.
MENU: By pressing this button, the user can activate the main menu of the receiver. EXIT: By pressing this button, the user can exit from the menu without saving the made changes or go one step back in the menu structure. cursor UP: By pressing this button, the user can jump to next channel on the channel list. In menu structure, user can move up one row. cursor LEFT: By pressing this button, the user can decrease the audio volume level of the receiver.
5.2 Front Panel 1. FRONT FLAP: - IRDETO SMARTCARD SLOT Above the Common-Interface Slot you’ll find a Slot for an IRDETO Smartcard. Please insert the smartcard with the chip first facing downwards. 2. CHANNEL UP Selecting TV/Radio channels 3. CHANNEL DOWN Selecting TV/Radio channels 4. POWER BUTTON Switch on- and off (Stand-by). 5. VOLUME DOWN Decrease the volume 6. VOLUME UP Increase the volume 7. 7-Segment Display In operation displays the current channel number.
5.3 Rear Panel No. Name FUNCTION 1 RF IN Input for Terrestrial Signal 2 RF OUT Loop-Output for Terrestrial Signal 3 USB USB 2.
6 WATCHING TV This chapter describes how to watch TV and listen to radios using the receiver. Thanks to the advantages of Digital TV transmissions, extra features are added to the broadcast, such as information about the current and next program and extra options such as the ability to choose between different languages for Audio and Subtitling. 6.1 General watching • Use the CHANNEL UP or CHANNEL DOWN keys to go to the next and previous channel respectively. • Use the NUMBER keys to input a channel number.
In Live TV Mode, press the OK key to open the Channel List. Move the cursor key UP / DOWN to move in the List channel-by-channel. Use the ‘< / >’ keys to jump 10 channels forward / backward. Choose your desired channel with the OK key. Exit the List with the EXIT key. Find a specific channel by pressing the BLUE (FIND) key on your remote control/ Enter the first letters of the desired Channel and press the YELLOW key to jump to the search result in the Channel List. Display Channels in Groups.
6.2 Options Subtitling language (GREEN key): The user can select from available subtitle languages, if more than one exists. Selection from the available choices is made with cursor UP or cursor DOWN key and confirmation by OK key. Some broadcasters also provide Subtitles in either, DVB- or Teletext Format. Audio track (RED key): Some TV channels broadcast multiple audio tracks, for example different languages or AC3 Audio tracks.
Move the cursor LEFT or RIGHT to move to another time of the current day. Use the BLUE key to advance to the next day and use the YELLOW key to go back by one day. For your orientation, please also note the timeline indicating the current time in comparison to the programs. For more detailed Information on a program, press the “i” (INFO) key. Please note that not all broadcasters provide EPG or detailed EPG data.
6.4 EPG-Timer (Timer programming via EPG) In the Single- or Multi-EPG Mode, you have the option to reserve programs in the timer. Move the cursor to the desired program and simply press the REC key on your remote control. An additional window is opened, which displays the timer reservations. If a HDD is connected, the recording will be made accordingly to the connected external HDD. If no HDD is connected, the receiver will switch to the according channel at the program time.
6.6.2 EPG Recording Via the EPG, you can program a Timer reservation – Please also see 6.4 for more details. 6.6.3 Timer Recording via manual Record List Alternatively to programming an Event via the EPG, you can also program an Event manually (Start-/End-Time, Channel) via the RECORD List. Open the MENU and open the submenu MULTIMEDIA/ RECORDING LIST and confirm with OK key. Add an Event manually by pressing the YELLOW (ADD) key.
6.6.4 TimeShift-Function During Live TV, you can press the PAUSE key to activate the TimeShift function. Provided you have connected a USB HDD, the Receiver will pause the program. With the PLAY key, you can continue to watch the time shifted program. The Information Bar indicates how much time you are watching time shifted compare to the live program. As with Playback, you can Fast-Forward and Rewind within the TimeShift Mode.
Under FILE LIST, press the RIGHT key to navigate to the MediaExplorer. Here you will find media files that are stored on your USB HDD. Move to the file you wish to play and press the OK key. Note that due to the numerous different file formats that are available, some files couldn’t be played back. By pressing the FAST FORWARD or REWIND keys, you can increase the playback speed to 2, 4, 8 and 16x in both directions. To stop playback press the STOP key.
7 MENU OPERATION The main menu can be activated by pressing the MENU key. Main menu provides access to most important functions and features of the receiver. These are divided into the following Menus. Each Menu contains corresponding sub-menus. The Main Menu consists of: • Edit Channels • Installation • User Setup • Mulimedia • Smartcard • System You can move between the Main Menu by pressing the cursor UP or cursor DOWN key.
8 EDITING CHANNELS 8.1 Create Channel List This menu is used to shape your channel list according to your personal preference. Press the MENU key, select ‘Edit Channels’ by using the RIGHT cursor and press OK. Change between TV and Radio Channels by pressing the TV/RADIO key. The individual functions are: Command Key Function Lock RED Lock and unlock a Channel (i.e.
8.2 Edit Favorite Channels This menu is used to create a list of your favourite channels. Thus you can create up to 8 different Favorite Lists. Press the MENU key, select EDIT FAVORITE CHANNELS by using the RIGHT and DOWN key and confirm using the OK key. Use the RIGHT or LEFT keys to jump between All TV and the chosen FAV List.
9 INSTALLATION This menu contains following items: • • • • Automatic search cable Manual search cable Automatic search terrestrial Manual search terrestrial 9.1 Automatic Search Cable & Manual Search Cable You have two options for the scan of cable channels. If you already know the parameters of the channels you wish to find, use the manual Channel Search and enter the required parameters accordingly. Otherwise use the Automatic Channel Search in which all Frequencies are scanned.
• Network Search: Choose „On“, if your Search is to include all Transponders, that are connected to a certain Network. Use the NAVIGATION Keys LEFT and RIGHT to toggle between „On“ and „Off“. • Search Range: Use the NAVIGATION Keys LEFT and RIGHT to toggle between All Channels, Free-To-Air or Scrambled Channels. • Logical Channel: By setting the option to „On“ the sequence of channels in your channel list changes according to what has been determined by your operator.
9.2 Terrestrial Scan In automatic channel search choose your region, search range and the logical channel (if available), then start the channel search using the RED key. If all values of the channels are known then choose Manual channel search and enter the following values. • Search Mode: Choose Auto for automatical Searching of all available Frequencies. If you prefer to search single Frequencies, choose manual. • Region: With the Regional settings you can change the geographical and cultural value.
10.1 Language Setting • Menu Language: Select the preferred language for the system menus. st nd • Audio Language (1 / 2 ): Some TV programs send multiple audio tracks, for example in two different languages. If there are no audio tracks available that match your settings, another language may be used instead. st nd • Subtitle Language (1 / 2 ): Select the preferred language for the subtitling and Program information. • EPG Language: Select the preferred language for the Electronic-Program-Guide 10.
10.3 Parental Control To use the Parental Control function, you will be asked to enter your access PIN code. All parental control features work on a locking concept with the PIN code as your entrance key. The default PIN code is set to ‘0000’. - Change PIN code: Use this function to change your PIN code to some other four-digit number. - New PIN: Enter a new four-digit PIN code by pressing the OK key and using the number keys on your remote control.
• Aspect ratio: User can inform the receiver about the display aspect ratio of the TV that is connected to the receiver. Possible choices are ‘Auto, 4:3, 16:9’ aspect ratios. • Display Format: If you select the display aspect ratio of TV as “4:3”, then also the preferred aspect ratio conversion scheme for cases in which the transmitted Program is in “16:9” format can be chosen.
10.6 Automatic Power Down In this Submenu, you can choose the time after which the receiver will go into Standby (Sleep-Mode). Provided the receiver is not undertaking any task such as recording, and also provided there is no input via the remote control or the front panel keys, the receiver would go into Standby after the set time. Options are: Off (None), 0:30m ~ 3:00h in 30min.
11.1 Record List (Timer) A Timer is used to program the receiver to switch on and off again at certain times and to tune to a specified channel. Timers are normally used to record a TV program on the video recorder or to pre-program the receiver for other reasons (i.e. wakeup). A set timer causes the receiver to wake up from standby mode at the specified time or change the channel to the specified one. Note: Timer settings that have been programmed in the EPG (see EPG-Timer point 6.
11.2 PVR Settings In this Sub menu, you can select the default duration for direct recordings. For direct recordings, a window appears after pressing the REC key which displays this pre-defined setting. Before beginning the recording, this st can be adjusted. The 1 suggested option is automatically the end time of the current event that the receiver draws from the EPG Information, if provided by the channel operator.
HDD Information displays the File System, the Total-, Used- and FreeSize of the connected USB Hard-DiskDrive. HDD Speed gives you the option to perform a speed test to verify that the speed of your connected USB HardDisk-Drive suits the tasks you wish to perform. - SD: For recording of SD channels - HD: For recording of HD channels - HD + Tms: For recording of HD channels and TimeShift Playback Formatting: After confirming with the OK key, the HDD is formatted.
12 SMARTCARD After opening the smartcard settings, the menu will display details of the inserted CryptoGuard Smartcard. Information includes settings and details on your subscription, age settings and changing of the PINCode of the smartcard. 13 SYSTEM The System Menu has 4 Sub menus: - Information, - Software Upgrade, - Default Setting, - OTA. The Information Sub menu is used to display information about the receiver and its hardware, software and loader. 13.
13.1.1 OTA (or OTC) Software Upgrade The software’s upgrade will be automatically made via OTA or OTC system. 13.2 Default Setting In this menu, you can delete all channels for TV or Radio. Additionally you can perform a factory reset to set back Channels, the Configuration to the original state as well as perform a Default Setting. Note: it is highly recommended not to perform any factory reset without the presence/injunction of a Technical Operator.
14 TROUBLE SHOOTING Problem LED on front panel does not light No picture or sound Possible causes Remedy AC Power cord disconnected Wrong connection of the Video/audio output to TV input terminal Connect power cord properly into the power socket Connect correctly with HDMI cable or RCA Wrong connection of antenna cable Connect the antenna cable correctly No signal or weak signal Check the cable connections and Antenna alignment Wrong setting of channels Information in MENU screen Your TV mode is d
15 TECHNICAL ASSISTANCE Dear Customer, Should you require technical assistance and your dealer or installer was not able to help, please contact our technical support.