Dimension One Spas – @Home Series Owner’s Manual Spa Information My Spa Model Name: Serial Number: Date Purchased: Date Installed: Gallons/Liters: Notes: Dealer Information: Dealer’s Name: Address: City: State, Zip: Telephone: Fax: i
Dimension One Spas – @Home Series Owner’s Manual Table of Contents IMPORTANT SAFETY INSTRUCTIONS..........................................................................................................1 IMPORTANT SAFETY INSTRUCTIONS (CANADA) (CSA SAFETY INFORMATION) ..........................2 HYPERTHERMIA .................................................................................................................................................3 SAFETY DO’S AND DON’TS.................................
Dimension One Spas – @Home Series Owner’s Manual IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY When installing and using this equipment, basic safety precautions should always be followed, including: Risk of Accidental Drowning. Extreme caution must be exercised to prevent unauthorized access by children. To avoid accidents, ensure that children cannot use or approach the spa unless they are supervised at all times. • Risk of Serious Injury or Death.
Dimension One Spas – @Home Series Owner’s Manual IMPORTANT SAFETY INSTRUCTIONS (CANADA) (CSA SAFETY INFORMATION) In addition to the preceding safety instructions, Canadian owners should read and understand the following information from the Canadian Safety Association: READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY • • • • • • • • • • • • • • • • • • • • • • • • • 2 A green colored terminal or a terminal marked G, GR, Ground, Grounding, or the symbol * is located inside the supply terminal box or compartme
Dimension One Spas – @Home Series Owner’s Manual • • • • • • Do not permit electric appliances (such as a light, telephone, radio, television, etc.) within 1.5m of this spa or hot tub. AVERTISSEMENT: NE PAS PLACER D’APPAREIL ÉLECTRIQUE (LUMINAIRE, TÉLÉPHONE, RADIO, TÉLÉVISEUR, ETC.) À MOINS DE 1.5 M DE CETTE CUVE DE RELAXATION. Maintain water chemistry in accordance with manufacturer’s instructions. ATTENTION: LA TENEUR DE L’EAU EN MATIERÈS DISSOUTES DOIT TRE CONFORME AUX DIRECTIVES DU FABRICANT.
Dimension One Spas – @Home Series Owner’s Manual Warning Signs Each spa has been provided with a Warning Sign and an Important Notice label. This label outlines safety precautions. This sign should be permanently placed in a location that is visible to the spa user.
Dimension One Spas – @Home Series Owner’s Manual Initial Startup IMPORTANT: About your GFCI Circuit Breaker — The GFCI (Ground Fault Circuit Interrupter — also called a "circuit breaker") is an electrical safety switch that automatically shuts off power to the spa in case of an electrical malfunction. You must have a GFCI installed according to your local building codes in an electrical power box near your spa. The GFCI should be OFF before you fill your spa.
Dimension One Spas – @Home Series Owner’s Manual 7. Remove the two shipping bolts located on the front of the pump mount (circled in illustration). 8. If your spa has a bleeder valve in the skimmer area (see picture at right) remove it to allow air to escape from the pump(s) while you are filling the spa. To remove the bleeder, unscrew it until it comes all the way out of the spa wall. Note: Don’t forget to replace the bleeder valve later after the pumps are operational. 9.
Dimension One Spas – @Home Series Owner’s Manual function properly. Once the jets are working, be sure to close the bleeder valves (opened when you originally filled the spa) tightly. 12. One minute after the power is turned on, the spa will automatically begin its first one-hour filtration cycle (this cycle may be interrupted if you are turning the Jet pumps on and off at the time, but that’s OK). On twopump models, Pump 2 will operate on high speed for the first minute of each filter cycle.
Dimension One Spas – @Home Series Owner’s Manual Operation You control the functions of your spa using the topside Control Panel. Gain a thorough knowledge of the following information before starting up your spa The Control Panel Control 1 Function 1. Display Window The Display Window shows the current status of the hot tub, its monitoring functions, self-diagnostics, or programming messages. By default it shows the spa water temperature. 2 2.
Dimension One Spas – @Home Series Owner’s Manual Control 4 Function 4. HEAT Indicator Light This light glows when the heater is on. 5 5. JETS 1 Button On American models, pushing the JETS 1 Button once starts the pump on LOW speed. Pushing it a second time turns on HIGH speed. Pushing it a third time turns the pump off. (European models have only one jet speed: High).
Dimension One Spas – @Home Series Owner’s Manual Control 8 Function 8.TEMPERATURE Buttons You control the water temperature with the Up (+) and Down (-) Buttons. Push a button once to change the temperature by one degree, or hold it down to rapidly change it by many degrees. For your safety, the temperature can be set no higher than 104 ° F (40° C).
Dimension One Spas – @Home Series Owner’s Manual Long and/or numerous filter cycles could cause overheating of the hot tub, especially in hot climates. Temperature Unit Selection (°F or °C) Pressing the Program button again brings you to the setting for the Temperature Units. Use the UP or DOWN Buttons to choose Fahrenheit (°F) or Celsius (°C). The factory default setting is Fahrenheit on American models and Celsius on European models.
Dimension One Spas – @Home Series Owner’s Manual Features Unique to Certain Models Jet Zone Selector Water Feature Flow Control NeckFlex Jet Pillow Stereo Sound System If your spa is equipped with the Jet Zone Selector, you can rotate this knob on the topside controls to change the flow of water from one group of jets to another.
Dimension One Spas – @Home Series Owner’s Manual Routine Equipment Maintenance Draining Your Hot Tub Your spa is gravity-drained, without the need for a pump. To drain the spa, locate the hose bib, which you attached to the spa in the Initial Setup operation, on the base near the lower right side of the equipment panel. Remove the cap (if any) from the hose bib.
Dimension One Spas – @Home Series Owner’s Manual Do not attempt to remove the lens without the special tool. If you have lost it, contact Dimension One Spas Service Department to have one sent. Be sure the rubber O-ring behind the lens is undamaged and is properly positioned when replacing the lens. Contact Dimension One Spas if you need a replacement O-ring.
Dimension One Spas – @Home Series Owner’s Manual Special Cold Weather Instructions All Dimension One Spas are designed for year-round use. They are insulated for energy efficiency and to protect the plumbing and equipment when the spa is operational. The spa has a freeze protection mode to circulate water during freezing weather, assuming the spa has electrical power and the proper water level. Therefore, keeping your spa operational is your best defense against freeze damage.
Dimension One Spas – @Home Series Owner’s Manual 12. Remove jet faces and insert the hose of a high-pressure air blower into each jet fitting. Continue this process, until no more water comes out of any jet fitting or drain fitting, and you no longer hear water gurgling within the plumbing. Place all jet faces in a plastic bag and set aside until you are ready to use your spa again. 13. Remove both bleeder valves from the top of the filter canister area.
Dimension One Spas – @Home Series Owner’s Manual • • Put your filter(s) back in. Refill spa and treat chemically as you would during a normal water change. Your system is equipped with automatic freeze protection. However, power outages can cause your system equipment to freeze quickly. During freezing conditions, check your system frequently to ensure proper operation. Always check your system after any power failure to ensure that it is operational.
Dimension One Spas – @Home Series Owner’s Manual Troubleshooting Guide Heating System Symptom Problem Corrective Action Does not heat 1. Temperature setting is too low Dirty filter Pressure switch malfunction 1. Turn up the “set temperature” on the control panel 2. 3. Clean filter. Call your dealer for service. Temperature setting is too high High limit tripped 1. Turn down the “set temperature” on the control panel 2. Call your dealer for service 2. 3. Too hot 1.
Dimension One Spas – @Home Series Owner’s Manual 19
