PARTS AND SERVICE MANUAL FOR DIMPLEX 26” OUTDOOR ELECTRIC FIREPLACE Model DFO2607
TABLE OF CONTENTS OPERATION PAGE 2 PARTS DRAWING PAGE 3 PARTS LIST PAGE 4 WIRING DIAGRAM PAGE 5 FRONT GLASS REMOVAL PAGE 6 UPPER LIGHT REPLACEMENT PAGE 7 LOWER LIGHT REPLACEMENT PAGE 8 MAIN ON/OFF/FLAME CONTROL REPLACEMENT PAGE 9 FLAME ROD AND MOTOR REPLACEMENT PAGE 10 CIRCUIT BOARD REPLACEMENT PAGE 11 AUDIO BOARD REPLACEMENT PAGE 12 1
DFO2607 OPERATION ELECTRIC FIREPLACE MANUAL CONTROL The manual controls for the firebox are located in the upper right hand corner behind the access panel. To access the controls, open the upper access panel by pulling forward and down. To locate controls refer to Figure 3. NOTE: The main on/off switch/flame action and flame brightness controls are always illuminated as long as the unit is plugged in. A. Main On/Off Switch The ON/OFF SWITCH supplies power to the flames and over head lights. B.
12 5 4 3 6 10 2 7 1 9 8 11 3
DFO2607 REPLACEMENT PARTS FIREBOX, 26” – Dimplex CATALOGUE NO. PART NO. DFO2607 6903100200 REPLACEMENT PART 1. MOTOR, ASSEMBLY 2. LED LIGHT, TOP 3. SWITCHBOARD 4. CIRCUIT BOARD 5. MIRROR 6. GLASS FRONT 7. LED LIGHT, BOTTOM 8. TRANSFORMER 9. FLAME ROD 10. BUSHING 11. LOGSET 12.
5 4X "C" TERMINAL SPEAKER TERMINAL 4 X "A" TERMINAL LIGHT WIRE HARNESS REFER TO DWG# 2500420000 2 X "A" TERMINAL 1 WATT LED FLAME LIGHT (BACK SIDE VIEW) AUDIO BOARD 3 WATT LED FLAME LIGHT FLICKER MOTOR P/N 300240200 (HARNESSINCLUDED) 1 WATT LED FLAME LIGHT 4X"A"TERMINAL BLACK WIRE OF CABLE TO LINE UP WITH SQUARE SOLDER PAD OF CONNECTOR BOARD. INCLUDE DIN LIGHT WIRE HARNESS INCLUDED IN LIGHT WIRE HARNESS YELLOW WIREOF CABLE TO LINE UP WITH SQUARE SOLDER PAD OF CONNECTOR BOARD.
DFO2607 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Lights need to be replaced when you notice a dark section of the flame. There are three lights under the log set which generate the flames and embers located under the emberbed. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life.
DFO2607 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Lights need to be replaced when you notice a dark section of the flame. There are three lights under the log set which generate the flames and embers located under the emberbed. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life.
DFO2607 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. Lights need to be replaced when you notice a dark section of the flame. There are three lights under the log set which generate the flames and embers located under the emberbed. It is a good idea to replace all of the lights at one time if they are close to the end of their rated life.
DFO2607 Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. MAIN ON/OFF SWITCH REPLACEMENT 1. 2. 3. 4. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws. Remove the 10 retaining screws and lift the top off of the unit. Locate the main on/off/flame control mounted on the top panel and disconnect the wiring plug noting it’s original location. 5.
DFO2607 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. FLAME ROD AND MOTOR REPLACEMENT 1. 2. 3. 1. 4. 5. 6. 7. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws.
DFO2607 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE CIRCUIT BOARD 1. 2. 3. 4. 5. 6. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws.
DFO2607 If unit was operating prior to servicing allow at least 10 minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons. TO REPLACE THE AUDIO BOARD 1. 2. 3. 4. 5. 6. Remove the front glass as shown on page 6 of this manual. Remove the top trim piece by removing the 3 retaining screws. Remove the 10 retaining screws and lift the top off of the unit.
