Service Manual Mozart Fireplace Model Numbers: CFP3913 REV 00 PCN 11637 DATE Sep 23, 09 Dimplex North America Limited 1367 Industrial Road Cambridge ON Canada N1R 7G8 1-888-346-7539 www.dimplex.com In keeping with our policy of continuous product development, we reserve the right to make changes without notice.
Table Of Contents Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3 Exploded Parts Diagram and Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 4 Wiring Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 5 Light Bulb Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 Mirror Replacement. . . . . . . . .
Operation Figure 2 Electric Fireplace Manual Control The manual controls for the unit are located behind the control panel on the front of the firebox (Figure 1). A switch is in the ON position when the side with the markings on it (i.e. I, or II) is pushed in. Figure 1 On Button Battery Off Button C Control Panel B A Battery Cover Battery Installation/Replacement 1. Depress tab on the battery cover on the back of the remote transmitter and remove battery cover (Figure 2). 2.
Exploded Parts Diagram 15 10 11 1 12 3 9 14 13 2 5 8 7 4 6 Replacement Parts List CFP3913 Part Number 6904890100 Replacement Part: 1. Log set. . . . . . . . . . . . . . . . . . . . . . . . . . . 0439290100RP 2. Flicker Motor. . . . . . . . . . . . . . . . . . . . . . 2000210100RP 3. Flicker Rod . . . . . . . . . . . . . . . . . . . . . . . . 5901110100RP 4. Heater Assembly . . . . . . . . . . . . . . . . . . . 2200491000RP 5. Cutout. . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Diagram Remote Receiver Board Flicker Motor Low Heat Switch High Heat Switch 3 Position On/Off Switch Cutout Cord Set Power Terminal Block Heater Assembly Circuitry Terminal Block Wire # 1. 2. 3. 4. 5. Colour Yellow Grey Grey Grey Blue 6. 7. 8. 9. 10. Red Blue Red Red Black 11. 12. 13. 14. 15. Black Blue Black Blue Blue 5 16. 17. 18. 19.
Light Bulb Replacement Mirror Replacement Allow at least five (5) minutes for light bulbs to cool before touching bulbs to avoid accidental burning of skin. If the fireplace was operating prior to servicing allow at least five (5) minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame. There are two (2) bulbs behind the log set which generate the flames and embers.
Figure 5 Figure 7 Trim Screws to remove (12) Screws (2) Mirror Retaining Bracket Mirror Log Set Do not remove these 2 screws Switch Replacement If the fireplace was operating prior to servicing allow at least five (5) minutes for light bulbs and heating element to cool off to avoid accidental burning of skin. Rear view of firebox Disconnect power before attempting any maintenance or cleaning to reduce the risk of electric shock or damage to persons.
the firebox. Figure 9 11. Pull the Flicker Rod to the far right, towards the Flicker Motor, then bend it gently enough to clear the bracket on the left (Figure 8).
7. Remove the seven (7) screws that attach the Top Panel to the firebox. There are: two (2) Phillips screws along each side at the top edge of the firebox; and three (3) Phillips screws at the back of the firebox, along the top edge (Figure 6, page 7). Remove the Top Panel. Figure 11 8. Remove the two (2) Phillips screws that attach the Mirror Retaining Bracket in place (Figure 7, page 7) and remove. 9. Slide mirror up from within the firebox to remove. 10.
23. Turn firebox on it’s back. Mounting Bracket will separate here as well); two (2) screws along each side; two (2) screws under the front edge of the firebox; and one (1) screw which connects to the Heater Assembly (Figure 10, page 9). The Bottom Panel can now be removed. 24.
vii) From within the firebox, disconnect the two (2) orange wires that connect to the back of the Low Heat Switch and the 3 Position On/Off Switch (there are four (4) wires and four (4) clips in total, but the wires are paired into two (2) piggy-back connections - one (1) per switch) (Figure 13). Figure 14 Cutout Screw Cutout Access to switches viii) Feed all disconnected orange wires through the sheet metal and remove the Cutout and wires from the firebox.
Mirror Retaining Bracket in place (Figure 7, page 7) and remove. to be inserted through the sheet metal of the chassis from the outside). 9. Slide Mirror up from within the firebox to remove. 21. Reconnect the three (3) wire clips from step 18 following Figure 15 as a guide. 10. Remove the Log Set by pulling it straight up and out of the firebox. 22. Follow steps 1 through 17 in reverse order to reassemble the fireplace. 11.
Figure 17 screwdriver, release the two (2) black wires from the Terminal Block (turn the screws of the Terminal Block counter-clockwise) which lead from the Power Cord. Take note of their original positions. Terminal Block Wire with smooth edges leads to narrow blade of plug Black wire leading from firebox 8. Use pliers to squeeze the portion of the Cable Clamp (Figure 17) that sits on the inside of the Access Panel and push cord and clamp through the panel. 9. Release the cord from the clamp. 10.
