Owner’s Manual Model Number: DCF7850 Quality checked by: Serial Number Model Number Part Number Valued Customer, Thank you and congratulations for purchasing a Dimplex electric stove. Over the years, valuable memories will occur around the warmth and comfort of your stove. Thank you for allowing our product to be the backdrop for those special moments.
QUICK REFERENCE GUIDE 1. Prior to the first use of the Corner Standing Stove, verify: • Are the circuit breakers for the stove on? • Are the light bulbs loose? (to check, follow the instructions for replacing the light bulbs under the Maintenance section of this manual) 2. The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by the initial heating of internal heater parts. 3.
CONTENTS Important Instructions . . . . . . . . . . . . . . . PAGE 4 Model and Serial Number Information. PAGE 6 Installation . . . . . . . . . . . . . . . . . . . . . . . PAGE 6 Operation. . . . . . . . . . . . . . . . . . . . . . . . . PAGE 9 Maintenance . . . . . . . . . . . . . . . . . . . . . . PAGE 12 Warranty . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT INSTRUCTIONS Retain this User’s Guide for Future Reference When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using the Corner Standing Stove. 2. The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation.
(one blade is wider than the other). The plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. Avoid the use of an extension cord. Extension cords may overheat and cause a risk of fire. If you must use an extension cord, the cord must be No. 14 AWG minimum size and rated no less than 1875 Watts. 15.
Model and Serial Number Information If you have any questions about our products please have the catalogue/model and serial numbers available upon calling customer service. To locate the catalogue/model and serial number labels see below (figure 1). Figure 1 Model Number Serial Number Rating Label Installation ! NOTE: A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases.
building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. Securing Cord (Figure 2) Figure 2 Power cord Securing Strap View from back Stabilizing Strap The Corner Standing Stove is designed to fit tightly into the corner of a room. This unit should be as close to the wall as possible.
Figure 3 Wall Anchor ⅛” (3mm) hole in wall Safety Strap Bolt Figure 4 Support hole Figure 5 Safety Strap 8
5. Hold strap in your hand with looped end in your palm. Insert free end though support hole and then through loop in the strap (Figure 5). 6. Insert screw through pre-punched hole in strap and screw into wall anchor (Figure 3). 7. Push unit into corner. Operation The controls (Figure 7) are located inside the door panel on the lower side of the Corner Standing Stove (Figure 6). Figure 6 Door Panel EMSC Models DCF7850 Models Figure 7 B A C A. Main On/Off Switch ” and “ Manual ”.
” position is for operating the unit with the provided remote The “ ” position the unit is operated with the ON and control. When in “ OFF buttons of the remote control. When the switch is in the center “ O ”position the unit is off. B. Heater On/Off Switch The Heater On/Off Switch supplies power to the heater element. When the switch is in the ON position the heater operates if the thermostat calls for heat. C.
Remote Control Initialization 1. Place the Main On/Off Switch (Figure 7A) in the OFF (“ O ”) position. 2. Wait a minimum of five (5) seconds and then place the Main On/Off Switch in the Remote Control (“ ”) position. 3. Within 10 seconds of changing the switch position, press the ON button located on the remote control transmitter (Figure 8). This will synchronize the remote control transmitter and the stove receiver. ! NOTE: You will have only 10 seconds to perform this last step.
Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. Light Bulb Replacement Allow at least five (5) minutes for light bulbs and heater to cool off before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears.
Figure 9 Screw Bottom of unit Rear Door Glass Cleaning The front glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the front glass may collect dust particles, these can be removed by dusting lightly with a clean dry cloth. To remove fingerprints or other marks, the glass can be cleaned with a damp cloth. The glass should be completely dried with a lint free cloth to prevent water spots.
Two Year Limited Warranty Products to which this limited warranty applies This limited warranty applies to your newly purchased Dimplex electric stove. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska. This limited warranty applies to the original purchaser of the product only and is not transferable.
What you must do to get service under this limited warranty Defects must be brought to the attention of Dimplex Technical Service by contacting Dimplex at 1-888-DIMPLEX (1-888-346-7539), or 1367 Industrial Road, Cambridge Ontario, Canada N1R 7G8. Please have proof of purchase, catalogue/model and serial numbers available when calling. Limited warranty service requires a proof of purchase of the product.
services. The purchaser is responsible for all expenses incurred for repair or replacement of such product or part including, without limitation, all shipping costs and transportation costs to and from the authorized dealer’s or service agent’s business and all labour costs. Such costs shall not be the responsibility of Dimplex. • On-site or in-home services not provided under this warranty may be performed at the purchaser’s specific request and expense at Dimplex’s then-current rates for such services.
