Owner’s Manual Model DF203A IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage.
Table of Contents Welcome & Congratulations. . . . . . . . . . . . . . . . . 3 Important Instructions . . . . . . . . . . . . . . . 4 Fireplace Installation . . . . . . . . . . . . . . . . . . . . . . . 7 Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . .
Welcome & Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Electalog, the world leader in electric fireplaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.
Important Instructions ① Read all instructions before using this heater. for examination, electrical or mechanical adjustment, or repair. ② This heater is hot when in ⑥ Do not use outdoors. use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.
Important Instructions soft surfaces, like a bed, where openings may become blocked. ⑫All electrical heaters have hot and arcing or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored or where it will be exposed to flammable vapors. ⑬ Do not modify the heater. Use it only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
Important Instructions ! NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Fireplace Installation Unpacking Instructions The fireplace insert is packed with the front glass panel separated and uninstalled from the fireplace. Care must be taken to unpack the fireplace so as not to damage the front glass. 1. Stand the packaged fireplace upright as indicated on the carton (Figure 1). 2. Open the top of the carton and locate which side the glass is placed. 3. Remove remote control and all plastic bags containing hardware etc. 4.
Fireplace Installation ! NOTE: Although the wood frame can be discarded, the screws and washers should be kept to attach the firebox to a Dimplex mantel or surround (if applicable). Fireplace Assembly The only assembly required is to place the front glass assembly onto the fireplace and install hardware to keep it in place. 1.
Fireplace Installation is preferred but not essential in all cases. A dedicated circuit will be required if, after installation, the circuit breaker trips or fuse blows on a regular basis when the heater is operating. Additional appliances on the same circuit may exceed the current rating of the circuit breaker.
Fireplace Installation Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons.Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician Make sure the units MAIN ON/ OFF switch is switched OFF (refer to operating instruction section). Plug the unit into a 15 Amp/120 VAC outlet.
Operation To access the controls, swing down the front cover panel located on the lower front of the fireplace (refer to diagram below). (Figure 8) A. Main ON/OFF Switch The switch has two ON positions marked with and “Manual”. The “Manual“ position is for manual operation. In this position the built-in remote control is bypassed. The position is for operating the unit with the provided remote control. When in position the unit is operated with the ON and OFF buttons of the remote control.
Operation CAUTION: If you need to continuously reset the heater, unplug the unit and call technical support at 1-888-346-7539. ! NOTE: The heater may emit a slight, harmless odor when first used. This odor is a normal condition caused by initial heating of internal heater parts and will not occur again. Remote Operation The fireplace is supplied with an integrated On/Off remote control. ! Note: Ensure that the fireplace 3 position switch is set to the remote control setting.
Operation the hand held transmitter (Figure 9). 2. Correctly install one 12 Volt (A23) battery in the battery holder. 3. Close the battery cover. Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. Light Bulb Replacement Allow at least 5 minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin.
Maintenance 6. Insert new bulb(s). 7. Install the light access cover and install the screws. Glass Cleaning Compact Fireplace Surface Cleaning Use warm water only to clean painted surfaces of the Compact Fireplace. Do not use abrasive cleaners. The glass is cleaned in the factory during the assembly operation. During shipment, installation, Servicing handling, etc.
Warranty One Year Limited Warranty Products to which this limited warranty applies This limited warranty applies to your newly purchased Electralog electric compact fireplace. This limited warranty applies only to purchases made in any province of Canada except for Yukon Territory, Nunavut, or Northwest Territories or in any of the 50 States of the USA (and the District of Columbia) except for Hawaii and Alaska.
Warranty • Electralog will in its sole discretion either repair or replace such defective product or part without charge. If Electralog is unable to repair or replace such product or part, or if repair or replacement is not commercially practicable or cannot be timely made, Electralog may, in lieu of repair or replacement, choose to refund the purchase price for such product or part.
Replacement Parts Log Set Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cutout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Position On/Off Switch. . . . . . . . . . . . . . . . . . . . . . . . Heater On/Off Switch. . . . . . .
