Owner’s Manual Model DFB4047 DF2305 DF2307SS 6901740259 DFB4047-NL IMPORTANT SAFETY INFORMATION: Always read this manual first before attempting to install or use this fireplace. For your safety, always comply with all warnings and safety instructions contained in this manual to prevent personal injury or property damage. To view the full line of Dimplex products, please visit www.dimplex.
Table of Contents Welcome & Congratulations . . . . . . . . . . . . . . . . 3 Important Instructions. . . . . . . . . . . . . . . 4 Site Selection & Preparation . . . . . . . . . . . . . . . . 7 Fireplace Installation . . . . . . . . . . . . . . . . . . . . . 10 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Replacement Parts . . . . . . . .
Welcome & Congratulations Thank you and congratulations for choosing to purchase an electric fireplace from Dimplex, the world leader in electric fireplaces. Please carefully read and save these instructions. CAUTION: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and will void the warranty.
Important Instructions When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: ① Read all instructions before using this appliance. ② The heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. The trim around the heater outlet becomes hot during heater operation.
Important Instructions not block air intake or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. ⑬ All electrical heaters have hot and arching or sparking parts inside. Do not use in areas where gasoline, paint, or flammable liquids are used or stored or where the unit will be exposed to flammable vapours. ⑭ Do not modify the fireplace. Use it only as described in this manual.
Important Instructions WARNING: Remote control contains small batteries. Keep away from children. If swallowed, seek medical attention immediately. WARNING: Do not install battery backwards, charge, put in fire or mix with used or other battery types - may explode or leak causing injury. ! NOTE: Changes or modifications not expressly approved by the party responsible for compliance could void user's authority to operate the equipment.
Site Selection & Preparation This section provides easy step by step instructions for selecting a location and preparing the site to install the fireplace into: • Existing fireplace • New wall construction • Dimplex mantel surround kit or custom made mantel surround ! NOTE 1: A 15 Amp, 120 Volt circuit is required. A dedicated circuit is preferred but not essential in all cases.
Site Selection & Preparation the fireplace insert. Ensure that all four (4) of the insert’s feet rest securely on this surface. Option #1 - The power cord can be lead from behind the fireplace trim and along the wall to an outlet near the fireplace. Option #2 - A new outlet can be installed inside the new frame construction. Figure 1 23 3 8" (594 mm) Option #3 - The power cord can be lead from behind the mantel and along the wall to an outlet near the fireplace. Existing Fireplace Installation 1.
Site Selection & Preparation 4. The power cord can run along the front of the hearth to an outlet near the fireplace. WARNING: To prevent personal injury you should hire a professional to cap the chimney flue or cut a hole in the existing fireplace for wiring. If you return your existing fireplace to its original use (example wood burning), it should be inspected by the local building department prior to use to reduce the risk of fire and personal injury. New Wall Construction 1.
Site Selection & Preparation 5. Assemble the mantel surround kit (refer to the mantel assembly instructions) or construct the custom surround with an opening of 24 inches (610 mm) wide X 23 ¼ inches (591 mm) high X 11 ½ inches (292 mm) deep. WARNING: Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. Fireplace Installation 1.
Operation Figure 3 A A - Three Position On/Off Switch The power switch has two (2) On positions marked with “ I ” and “ II ”. The “ I ” position is for manual operation. In this position the built-in remote control is bypassed. The “ II ” position is for operating the unit with the provided remote control. When in “ II ” position the unit is operated with the ON and OFF buttons of the remote control. When the switch is in the center (“ O ”) position the unit is off.
Operation Figure 4 ON Button OFF Button Battery Battery Cover Resetting the Temperature Cutoff Switch The heater is protected with a safety device to prevent overheating. Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the On/Off Switch to Off and waiting five (5) minutes before switching the unit back on.
Operation Battery Replacement ① Slide battery cover open on the hand held transmitter (Figure 3). ② Correctly install one (1) 12 Volt Battery must be recycled or disposed of properly. Check with your Local Authority or Retailer for recycling advice in your area. (A23) battery in the battery holder. ③ Close the battery cover. Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons.
Maintenance Replacement: 1. Remove the front glass by removing the two (2) outer screws holding the glass clips (Figure 5). 2. Remove the log grate by removing the two (2) mounting screws (Figure 6). 3. Remove the log set by lifting straight up (Figure 7). 4. Slide the light assembly slightly out of the insert approximately one (1) inch. 5. Examine the bulb(s) to determine which bulb(s) require replacement. 6. Unscrew the bulbs counter clockwise. Figure 7 7. Insert new bulbs. 8.
Maintenance Glass Cleaning The glass is cleaned in the factory during the assembly operation. During shipment, installation, handling, etc., the clear door may collect dust particles, these can be removed by dusting lightly with a clean dry cloth. To remove fingerprints or other marks, the clear door can be cleaned with a damp cloth. The clear door should be completely dried with a lint free cloth to prevent water spots.
Warranty how long defect Products covered by this limited warranty have been tested and inspected prior to shipment and, subject to the provisions of this warranty, Dimplex warrants such products to be free from defects in material and workmanship for a period of 12 months from the date of the first purchase of such product.
Warranty CONTRACT, IN TORT, OR ON ANY OTHER BASIS, FOR ANY INDIRECT, SPECIAL, PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR INCIDENTAL LOSS, COST, OR DAMAGE ARISING OUT OF OR IN CONNECTION WITH THE SALE, MAINTENANCE, USE, OR INABILITY TO USE THE PRODUCT, EVEN IF DIMPLEX OR ITS directors, officers, or AGENTS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES, COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS, OR DAMAGES ARE FORESEEABLE.
Replacement Parts Log Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0438200700RP Flicker Motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000220100RP Flicker Rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5900340100RP Heater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2200490800RP 3 Position On/Off/On Switch. . . . . . . . . . . . . . . . . . . . . . . . . .
